Thank you very much for your video, it is simple and perfect to understand. That's exactly what I needed. Recently my rear controller burned out, I ordered new controllers that I was told would be the new version 2 model, which comes equipped with the TF-100 display. I bought turn signals that have brake flashes and I would like to add the brake light from a mercedes and give me a night light as well. I would like to ask you how many devices I can connect with just one cable that comes out of the controller for the brake signals, and how can I do that, since the voltage of the lamps is the same but it won't have enough power to power all those lights... Thank you for teaching me with all your videos
Keep in mind the brake lights line only comes on when you pull one or both brake levers. If the lights you add are LED, it likely will handle a few extra as LEDs generally don’t draw much power.
I assume you mean the LED driver harness for the tail lights and front running lights. I couldn’t find them on-line but I have one I can give you for $20 to cover shipping. If interested, email me: maikemarx@gmail.com. U could also try to email Laotie at: support@laotie.zone
Muchas gracias por tu tutorial explicativo.¿Que ocurre si le coloco al ti30 un converter DC-DC 60V-12V-5A max para ue todo el circuito electrico funcione a 12?.¿tendria que anuar alguna placa de circuito del tentaculo de cables?..yo creo haber visto en algun video de "pirate" escooters donde al colocar un converter identico crei aver comprendido que se tenia que anular esa placa circuito plana..Te lo pregunto porque estoy en ese punto donde le puse todo tunig y ahora es momento de conectar todo y me falta tener claro ese punto. En el video e "PIRATE" no se ve claro ni el como ni el donde..¿podrias hacer un video explicativo dobre este asunto?.gravis por tu canal .pasa un buen dia
The flat circuit board is not a converter, it’s just a distribution board. The stock lights all run off of the battery voltage. Yes you could connect up a dc to dc converter to run some other 12v lights. I installed a dc to dc (5v) converter to run some RGB LED lighting on mine. Just connect the dc to dc converter input to the same place as the input to the lighting cable (orange/black 2 pin female) as shown in the video. Make sure the dc to dc converter can accept an input up to 67.2v which is the battery voltage when fully charged.
3pin male red/blue/black from switch module to 3 pin Female red/blue/black from scoot harness (Octopus cable). 2pin M green/black to left turn signal. 2pin M brown/black to right turn signal. 2pin M with one yellow(may be red on some scoots) and two black wires goes to one of the 2pin F red/black from the Yunli controller harness.
Hi, I’m having a problem with my display when I connect the battery I hear baby noise on the alarm, but the power doesn’t turn on on the display. Do you have any idea where it could be the problem?
I would definitely not connect up a reverse cable. Why would you ever want the motors to go in reverse? I went away from the Qiewa controllers years ago. Not sure what they’re selling now.
I haven’t installed mine yet in my ti-30. Want to test the stock ones first so I can compare the difference. Probably will be another month or so. However, with the controllers and display all being swapped, you definitely need to check the P settings. It should be functional without doing that but maybe the speed setting might not be set for 100 or full speed etc. once I swap mine I’ll do a video on the hookup and p settings.
@@Desert-Ecruising Im asking this because i burnt 2 controllers 🥹, the laotie support team sent me 2 videos and i followed the connections right, i just didnt check the p settings, i didnt change the magnets settings etc, so idk what was the cause, i will wait for one of your videos in case you change to yunli controllers
I do have the yunli controllers and will definitely be installing them and doing a video. There is nothing in the P settings that could cause you to burn the controllers regardless of the settings. The magnet setting does nothing more than adjust the displayed speed and mileage on the display.
No, you need two good controllers. For ultimate performance, I recommend replacing the JP controllers with the Yunli sinewave controllers paired with the Yunli DS20 throttle.
Witam mam pytanie o kontrolery. Czy lepiej działają niż oryginał? Oryginalny jak dla mnie działa tak 0 albo 1, brak płynności podczas dodawania gazu. Czy nowe kontrolery działają lepiej? Bardzo proszę o odpowiedź
I have not yet installed the Yunli controllers but they are supposed to be more linear since they are sine wave controllers. I’m testing out the stock controllers now and will swap them out in a few weeks.
Myślałem że masz już zainstalowane nowe kontrolery sinusoidalne, dlatego pytałem. Aktualnie jest spora obniżka na banggood. Prawdopodobnie kupię je ...
@@Gumis2323I have them but have been modifying the scoot since I got it. Have only ridden it one time. Want to test the stock controllers awhile before I swap them so I can compare the differences.
Dzisiaj zamontowałem nowy sterownik.... Działa lepiej niż oryginalny, na razie testuję. Reakcja na przepustnicę jest opóźniona, dziwne uczucie puszczasz akcelerator a hulajnoga dalej jedzie... Nie wiem jakie mają być optymalne ustawienia P- setings, Jak masz jakieś porady proszę o pomoc
Yes, that’s two different, unrelated things. The controllers are rated in Amps “A” and a 35A controller will push a max of 35A to the motors. The battery is rated in amp hours “Ah” which is just the capacity of the battery. The bigger the Ah rating, the more capacity the battery has. Think of it like the gas tank in a car. A bigger tank gives you more range.
Is there anybody here that knows of any videos that are this easy to follow but just for one rear running motor and the lighting and throttle braking singal lights and horn wiring setup? If anyone can help thank you
Thank you very much for your video, it is simple and perfect to understand. That's exactly what I needed. Recently my rear controller burned out, I ordered new controllers that I was told would be the new version 2 model, which comes equipped with the TF-100 display. I bought turn signals that have brake flashes and I would like to add the brake light from a mercedes and give me a night light as well. I would like to ask you how many devices I can connect with just one cable that comes out of the controller for the brake signals, and how can I do that, since the voltage of the lamps is the same but it won't have enough power to power all those lights...
Thank you for teaching me with all your videos
Keep in mind the brake lights line only comes on when you pull one or both brake levers. If the lights you add are LED, it likely will handle a few extra as LEDs generally don’t draw much power.
You are a genius, thank you very much
1:45 where can find this?? because my crashed...😢😢
Contact Ordospeed on Ali-Express. They are the factory store for the Yunli controller setup.
a.aliexpress.com/_msU1O48
Hello , nice info, where do you buy that circuit board for led lights from ? Thanks
I assume you mean the LED driver harness for the tail lights and front running lights. I couldn’t find them on-line but I have one I can give you for $20 to cover shipping. If interested, email me: maikemarx@gmail.com.
U could also try to email Laotie at:
support@laotie.zone
Muchas gracias por tu tutorial explicativo.¿Que ocurre si le coloco al ti30 un converter DC-DC 60V-12V-5A max para ue todo el circuito electrico funcione a 12?.¿tendria que anuar alguna placa de circuito del tentaculo de cables?..yo creo haber visto en algun video de "pirate" escooters donde al colocar un converter identico crei aver comprendido que se tenia que anular esa placa circuito plana..Te lo pregunto porque estoy en ese punto donde le puse todo tunig y ahora es momento de conectar todo y me falta tener claro ese punto. En el video e "PIRATE" no se ve claro ni el como ni el donde..¿podrias hacer un video explicativo dobre este asunto?.gravis por tu canal .pasa un buen dia
The flat circuit board is not a converter, it’s just a distribution board. The stock lights all run off of the battery voltage. Yes you could connect up a dc to dc converter to run some other 12v lights. I installed a dc to dc (5v) converter to run some RGB LED lighting on mine. Just connect the dc to dc converter input to the same place as the input to the lighting cable (orange/black 2 pin female) as shown in the video. Make sure the dc to dc converter can accept an input up to 67.2v which is the battery voltage when fully charged.
Hello dear. Where did you bought this led driver harness? I tried to look everywhere but I couldn't find it.
They came with the scoot. I have an extra one if you’re interested since I removed mine: maikemarx@gmail.com
@@Desert-Ecruising ok thank you I will email you
Need explanation with headlight switch to yunli controllers please
3pin male red/blue/black from switch module to 3 pin Female red/blue/black from scoot harness (Octopus cable).
2pin M green/black to left turn signal.
2pin M brown/black to right turn signal.
2pin M with one yellow(may be red on some scoots) and two black wires goes to one of the 2pin F red/black from the Yunli controller harness.
Hi, I’m having a problem with my display when I connect the battery I hear baby noise on the alarm, but the power doesn’t turn on on the display. Do you have any idea where it could be the problem?
Email me and I’ll try and help you.
maikemarx@gmail.com
On new controllers there is a reverse cable where does it go?
I would definitely not connect up a reverse cable. Why would you ever want the motors to go in reverse? I went away from the Qiewa controllers years ago. Not sure what they’re selling now.
hey, im trying to connect the yunli controllers on my laotie es19, do i have to change the p settings after plugging everything?
I haven’t installed mine yet in my ti-30. Want to test the stock ones first so I can compare the difference. Probably will be another month or so. However, with the controllers and display all being swapped, you definitely need to check the P settings. It should be functional without doing that but maybe the speed setting might not be set for 100 or full speed etc.
once I swap mine I’ll do a video on the hookup and p settings.
@@Desert-Ecruising Im asking this because i burnt 2 controllers 🥹, the laotie support team sent me 2 videos and i followed the connections right, i just didnt check the p settings, i didnt change the magnets settings etc, so idk what was the cause, i will wait for one of your videos in case you change to yunli controllers
I do have the yunli controllers and will definitely be installing them and doing a video.
There is nothing in the P settings that could cause you to burn the controllers regardless of the settings. The magnet setting does nothing more than adjust the displayed speed and mileage on the display.
@@Desert-Ecruising thank you!, i will be waiting then
@UnboxWave For reference, if you don’t mind, send me those videos from Laotie. maikemarx@gmail.com
Thenks
Olá tudo bem.
Tenho um controlador queimado posso por a funcionar só com um?
No, you need two good controllers. For ultimate performance, I recommend replacing the JP controllers with the Yunli sinewave controllers paired with the Yunli DS20 throttle.
@@Desert-Ecruising ola muito obrigado,pelo excelente video e dica sobre o controlador
@@Desert-Ecruising hello
One controler One motor
And I wave error E10
Can you help me pls
Hello. Can you help me connect an alarm on my electric scooter?
What scooter do u have?
@@Desert-Ecruising angwatt T1
Did it come with an alarm module?
@@Desert-Ecruising yes. The supplier said yes.
I don’t understand. It came with an alarm module installed but it doesn’t work? Is that what you mean? You can email me at: maikemarx@gmail.com
Witam mam pytanie o kontrolery. Czy lepiej działają niż oryginał?
Oryginalny jak dla mnie działa tak 0 albo 1, brak płynności podczas dodawania gazu. Czy nowe kontrolery działają lepiej?
Bardzo proszę o odpowiedź
I have not yet installed the Yunli controllers but they are supposed to be more linear since they are sine wave controllers. I’m testing out the stock controllers now and will swap them out in a few weeks.
Myślałem że masz już zainstalowane nowe kontrolery sinusoidalne, dlatego pytałem. Aktualnie jest spora obniżka na banggood. Prawdopodobnie kupię je ...
@@Gumis2323I have them but have been modifying the scoot since I got it. Have only ridden it one time. Want to test the stock controllers awhile before I swap them so I can compare the differences.
Dzisiaj zamontowałem nowy sterownik.... Działa lepiej niż oryginalny, na razie testuję. Reakcja na przepustnicę jest opóźniona, dziwne uczucie puszczasz akcelerator a hulajnoga dalej jedzie...
Nie wiem jakie mają być optymalne ustawienia P- setings,
Jak masz jakieś porady proszę o pomoc
If my scooter is 35ah controllers is it ok to get a 25ah battery?
Yes, that’s two different, unrelated things. The controllers are rated in Amps “A” and a 35A controller will push a max of 35A to the motors.
The battery is rated in amp hours “Ah” which is just the capacity of the battery. The bigger the Ah rating, the more capacity the battery has. Think of it like the gas tank in a car. A bigger tank gives you more range.
Ok thank u 🙏
If you buy a display with 6 pins, it works
@@marcopeixoto85 es português
Is there anybody here that knows of any videos that are this easy to follow but just for one rear running motor and the lighting and throttle braking singal lights and horn wiring setup? If anyone can help thank you