Stihl MS260 Pro Chainsaw Cylinder and Piston Replacement
ฝัง
- เผยแพร่เมื่อ 21 ส.ค. 2024
- UPDATE: the farmertec rebuild kit in this video did not work out. The piston wrist pin was loose and generated ~125psi (seen in the video) compared to the original cylinder/piston/wrist pin that generates ~145psi (even using farmertec rings!)
Stihl MS260 Pro chainsaw that would not start. Diagnosed it and saw a scored piston so I replaced the cylinder and piston.
Disclaimer:
Due to factors beyond the control of this video and/or TH-cam channel In-depth DIY, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. In-depth DIY assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. In-depth DIY recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of this channel, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained
I could kiss you. The kit I got didnt come with directions and couldnt find a video! Thank you!!
Your lucky to catch it in time to clean it up and new ring 😊
I saw where you said the rings compress by hand and go in easily. I thought you might have left that part out on purpose to keep the secret. That's actually the part I was looking for and wondering about. It would have been nice to see that critical part. That said, Great video, most informative and easiest to follow of all I've seen. I need to do a 362 but it wasn't worth $600 at the shop for a $900 saw. Thx
In my newer video rebuilding the Dolmar 7300, right at the 40 minute mark, I show pinching the ring and sliding the cylinder on. I usually angle it slightly away from the ring gap so I can continue to pinch the ring until the cylinder slides over on its own.
Good video. Nice tip on piston direction. I just tore down my 193t and I rubbed off the Stihl logo when cleaning and it does not have an arrow (I'm trying to re-use my factory cylinder and piston before I give up on them and buy a new kit). I also have a 026 and that is a very nice saw.
Why'd you skip showing how you got those C clips out?? With all the good info in this video, getting those clips out is the one thing I can't figure out. That's the reason I got on this video. I can't believe nobody else commented on this.
T-27 on the cylinder bolts.
I thought that was odd. Should be T-27 on the most Stihl units.
Any time a Stihl saw rolls over, immediately move it up to half choke and pull it over until it starts. If you pull it over after it rolls over, you will flood the saw.
This is true. Once it almost rolls over, move it up to half choke. Starts next pull. I had my own lawn care and have used a ton of Stihl equipment, had great success with their higher end units and have heard even the lower end works well.
@@NONO-hz4vo not always does it crank with one additional pull, but usually. Most of my saws average out at 3,2P but occasionally I get a 1,1P and have even had a 1,0P in real cold weather. 1,1P tells me the carb is only tuned for the temperature that day but it sure does help my arm and shoulder.
@John Clarke In good weather I can pull on full choke and quickly reach down and switch it to half and get her started. Always fun.
Excellent video. Keep up the good work.
I have the same chainsaw ... it has less than 10 hours of use. I have had to replace the piston twice for same issue, scored piston. Stihl is refusing to repair or replace the saw. It will cost me $275 to have a local Stihl dealer replace the piston. Obviously a defective lemon. I will never own another Stihl. Any suggestions or recommendations would be greatly appreciated.
Just get a poulan 4218 and you’ll be happy 😊
Not the saw. It's your oil and mixture. Use 32:1 and use amsoil. dominator.
I have a strimmer and unbolted the cylinder housing but it’s still stuck tight. Any tips ?
possibly from not being warmed up cold start and wot
Failure to let it ideal and warm up 😢😢
Who ranned this? I saw that kind of damage on the piston and I may have an idea of what happened.
In most cases, you see that stuff when the user jumps on it while it's cold.
Yep its cold damage, piston expands faster but cylinder isnt warming up that fast so the piston makes contact with cylinder
You miss how to compress ring into the vlinder
China cylinders and pistons mean huge power loss. Id of used the oem cylinder with a Meteor piston and caber rings. In fact thats what i did with mine!
I think there t 27s
What did you use as a ring squzeer to get piston in jug ? /
They can be squeezed by hand while sliding the jug on.
How did you compress the piston rings to get the piston back into the cylinder?
By hand. Small engine rings compress easy enough by hand and slip in on their own most the time. It's not as intense as a car engine.
@@in-depthdiy2123 oil mix 1:33 is ok ?
Cylinder bolts are T27.
They are 25 I just took one out
Didn’t use a torque wrench on the head bolts ?
I tighten the head bolts to snug-enough ft-lbs.
The torque on a small 2t engine like this is going to be a lot lower than the capacity of the bolts. Just snug them up as he did and you will be past the required torque.
What rebuild brand did you go with?
It's shown in the video around 6:35, it's farmertec.
@@in-depthdiy2123 thank you! Are you happy with the build quality of their aftermarket product?
@@Lauterbach24 It appeared to be good quality, but with only two tanks of gas through it I can't comment on the longevity. It assembled and fit well and runs as I expect it to.
@@in-depthdiy2123 thank you for the information.
@@Lauterbach24 I want to follow up and say the farmertec kit didn't work out in the end. It kept pushing around 125psi and it never generated enough power to be useful long term. After disassembly the piston wrist pin was loose. I used the farmertec piston rings on the original piston/cylinder/wrist pin and it's now at 145psi and plenty of power.
The heading said Stihl Pro chainsaw. Is a 260 Stihl Pro
Fat fingers. Is the 260 in Stihl Pro line?
@@ronkolb1335 It is a pro saw or if you wanna be accurate, it was.
No longer in production.
Toko seher 260
💯💯💯💯👍👍👍🤝🤝🤝
Are the parts from china