Growatt hybrid inverter has the RJ45 port and no RJ45 in the solar inverter. However, and it will be fine if you can split the Ethernet cable, and connect the 485A and 485B to corresponding ports of the solar inverter.
I have three SPH hybrid single phase inverters, one on each phase of three phase network. can one TPM be used to connect to all 3 inverters or do I need 3 separate TPM for each inverter, obviously all wired in series.
Hello, for technical support, please contact our service team at service@ginverter.com, or you can call our service hotline at +86 755 2747 1942. Thank you!
@@nicklasfisker196 their answer should have been yes, you cannot get the communication to all 3 since you can't just go split the signal and as far as I know there is no option to connect them together. Next time just buy a 3 fase inverter for a 3 fase grid connection
@@mikeg197 there is a wifi modbus solution based on sv611 Modbus can usually only provide a 1:1 communication but with 4 of these tiny boards I can use 1 smartmeter to provide the date for the SPH inverter and also a pulsar plus wallbox, so a 1 to 2 connection.
Hello, for technical support, please contact our service team at service@ginverter.com, or you can call our service hotline at +86 755 2747 1942. Thank you!
Hello, for technical support, please contact our service team at service@ginverter.com, or you can call our service hotline at +86 755 2747 1942. Thank you!
Growatt Mic TeX 600, Europe. For Sdm 630v2 set B to 8, A to 7. Adress in Growatt to 002.
Great, and where does the Growatt get hooked up? The Growatt has no RJ45 What are they showing?
Growatt hybrid inverter has the RJ45 port and no RJ45 in the solar inverter. However, and it will be fine if you can split the Ethernet cable, and connect the 485A and 485B to corresponding ports of the solar inverter.
I have three SPH hybrid single phase inverters, one on each phase of three phase network. can one TPM be used to connect to all 3 inverters or do I need 3 separate TPM for each inverter, obviously all wired in series.
Hello, for technical support, please contact our service team at service@ginverter.com, or you can call our service hotline at +86 755 2747 1942. Thank you!
What was their answer?
@@nicklasfisker196 their answer should have been yes, you cannot get the communication to all 3 since you can't just go split the signal and as far as I know there is no option to connect them together. Next time just buy a 3 fase inverter for a 3 fase grid connection
@@mikeg197 there is a wifi modbus solution based on sv611
Modbus can usually only provide a 1:1 communication but with 4 of these tiny boards I can use 1 smartmeter to provide the date for the SPH inverter and also a pulsar plus wallbox, so a 1 to 2 connection.
Can use with CTs?
Hello, for technical inquiries and support, please feel free to contact our service team at service@ginverter.com. Thank you!
With this configuration, how do you read the meter from a device/computer that is connected to the same network?
Hello, for technical support, please feel free to contact our service team at service@ginverter.com. Thank you!
What is the differences between Growatt SMD630 Modbus V3 and Eastron SMD630V2. Will Eastron units work as well?
Can I also control the export of the Growatt Min 3000 TL-XE 1 PH with the SDM630 3 PH?
Hello, for technical support, please contact our service team at service@ginverter.com, or you can call our service hotline at +86 755 2747 1942. Thank you!
did you get a reply? i have the same question. Would be a great solution.
How can I connect a smart meter to a heatpump ?
Hello, for technical support, please contact our service team at service@ginverter.com, or you can call our service hotline at +86 755 2747 1942. Thank you!
not working with 5000TL3 S
Hello, for technical support, please feel free to contact our service team at service@ginverter.com. Thank you!
Tell us the message??