Interesting video sir, sometimes the technician suspects the led strips and disarms all the equipment to access them. The deduction based on your analysis is very professional. Thank you for your time and for sharing it. 👏👍🙏🙋♂️
I am very impressed, the way you trace the problem, in a series very carefully, keep up the good work. Thank you for the instructions, greetings from Indonesia
Regularmente entiendo sus métodos de reparación, pero hoy la verdad no comprendí la solución al problema. No supe como llego a solucionar el problema. Acaso desactivo o puenteo alguna etapa de protección de Backlight? ... Saludos desde Nuevo León, México.
Great video. But I have a specific issue. I changed my board TP.sis231.p83 with the board TP.vst59.p818 because I couldnt get my oriiginal one firmware dump and the tv rarely passes logo screen from bootloop to hdmi or other source. Almost all connectors are plug and play but the only difference the new boards and this new one has a dual 2 pin led driver inlet while the old one had a 12 pin connector. Do I need a voltage regulator board as a bridge in between or I can rewire it directly? Cable for led backlight shows 105 v. Thanks
Hi Mr dear T as you showed the 2 mosfet which seemed had enough voltage even when plugged the cable in and I did not understand how you said they donot!!!!! Will. you please explan about that and clear it more? Thanks a lot and so glad having you in troubles time!
I’m watching all your videos but I have this same problem on my 58” skyworth android tv but don’t know what the volts are supposed to be, do you know where I can get a proper readout or schematics for that tv I can’t find one anywhere online? Or is there other cheap TVs that are basically same as the skyworth?
@@tevzTVTevatronics OK thanks anyways... can you make a video and explain from where the power goes in the border and where it runs from the plug in to the led panel and where or what the normal volts are supposed to be for capacitors and diodes and the bigger transistors ? I'm trying to figure out how or where to find the drivers for led are by just looking at the power board... I'll watch them again and try to figure out the volts.. I just with there was a video on tvs that explain what each section or part does and how to find them... but thanks keep the videos Coming I like them....cheerz
Hi Mr T. Can you please confirm that some tvs have type A and B strips inside due to centre strip being less brightness. I checked each strip to see centre strip is less bright and takes half the current . This is normal right?
Hello sir i have an lg 49 inch nanocell tv, it has standby light but no response from the power button, sometimes after a few minutes of pressing the tv tries to turn on and the standby light flashes and goes out like the tv is on, but no backlight , no image, no 5v usb output , the 13v from the psu is there and 3.3v is there on the main board and theres voltage on most of the inductors on the main board , the cpu is the only thing warming up, it gets hot as soon as i plug the power cable in , theres no shorts on the main , how else can i diagnose the problem ? Thankyou for any help sir. Reace , UK
Hi Tevz, I’ve one small question about backlight section of LCD, LED Tv or Monitors. I’ve seen many people ignore the DIM/Adjustable pin connection while they’re adding an Inverter Board (External) they just use Vcc, Gnd & Enable connection. So I’m very much curious to know about that DIM connection like from where this signal is coming from, which IC generates DIM singal and why we do not use it while adding inverter module. Thank you very much 🙏🏻
An SLC2013M driver IC is about a half-USD (50 cent) part, why not fix it the right way? There must be electronic stores there, or if you fix this many TVs you should have one in stock or lying around on a donor board. Except with companies such as Apple for which parts are not available, a patch job like this is not an acceptable repair and certainly not guaranteed to last for long.
@@tevzTVTevatronics I was thinking that myself and have been looking for a cheap one. The digital multimeters are not able to pick up those quick changes. I thought I was mistaken for thinking this but now your video has confirmed my thoughts.
Interesting video sir, sometimes the technician suspects the led strips and disarms all the equipment to access them. The deduction based on your analysis is very professional. Thank you for your time and for sharing it. 👏👍🙏🙋♂️
Another TV saved! Great job. Thanks for sharing.
I needed this video about a week ago when I ordered backlights for no reason pmsl
I still trying to figure out some of the work you did like this very one, but you create a solution out there keep it up sir.
I love your kitty cat😘😍😋
Very complex fix, way beyond me but loved the kitty cat at the end
I am very impressed, the way you trace the problem, in a series very carefully, keep up the good work. Thank you for the instructions, greetings from Indonesia
Thank you very much!
Круто! Наконец то новое видео от Tevz 👍👍👍 Лайки!
Maraming salamat po Sir tevz s pagbabahagi ng karanasan at kaalaman nyo. God bless po sa inyong sambahayan.
Good great best job thanks for sharing ❤️👌👍🏾👍🏾👍🏾👍🏾👍🏾👍🏾👍🏾🙏
Supper
Cat is very nice sir
Good job
and best new cat guest
Excellent sir , knowledgeable video thanks for sharing
Well done maestro. congratulations. Greetings from Serbia
Thank you very much!
Ótima solução, parabéns Tevz 👏
my great master ❤❤❤❤❤❤❤❤❤
sir exelint information
Nice one...
Great technique's...
God bless for sharing
I saved your video
Good boy
Hello ,from Pakistan
Buenas tarde Colega excelente trabajo saludos desde Argentina
well explained. thanks, please how do you solve line on LG 32INCHES SCREEN? THANKS
Very nice your video sir 🌹❤️
Hello..very mix
Hi thank you so much plz videos more
Good morning Ji sir Ji good job
Same to you
Nicely done
seguimos adelante, saludos.
Nice idol
Watching sir
Good job thank's❤❤
Good job
Very nice job ❤🥰🥰
Ikut nyimak pak...
Very useful in my life your TH-cam channel
It's my pleasure
Thanks sir
This repair is a bit hard for me 😂 i don’t really know where to where those wires are being connected to 😢
I think it was 13 volts path.
🧿👍
Indonesia hadir 🖐️☕
Good day
👌👍👍👍
Regularmente entiendo sus métodos de reparación, pero hoy la verdad no comprendí la solución al problema. No supe como llego a solucionar el problema. Acaso desactivo o puenteo alguna etapa de protección de Backlight? ... Saludos desde Nuevo León, México.
Very interesting video. There are a lot to learn from you.
Good work ❤️.
Say hello for me to little 😺 kitten.
Thank you! 😊
@@tevzTVTevatronics you are most welcome 😊
Great video. But I have a specific issue. I changed my board TP.sis231.p83 with the board TP.vst59.p818 because I couldnt get my oriiginal one firmware dump and the tv rarely passes logo screen from bootloop to hdmi or other source. Almost all connectors are plug and play but the only difference the new boards and this new one has a dual 2 pin led driver inlet while the old one had a 12 pin connector. Do I need a voltage regulator board as a bridge in between or I can rewire it directly? Cable for led backlight shows 105 v. Thanks
Hi Mr dear T as you showed the 2 mosfet which seemed had enough voltage even when plugged the cable in and I did not understand how you said they donot!!!!!
Will. you please explan about that and clear it more?
Thanks a lot and so glad having you in troubles time!
they dont turn on, boost, oscillate, step up.
I already face this foult this foult came from 12v small tramsformer supply..two capcitor for aux supply or supply voltages of primary small caps
I’m watching all your videos but I have this same problem on my 58” skyworth android tv but don’t know what the volts are supposed to be, do you know where I can get a proper readout or schematics for that tv I can’t find one anywhere online? Or is there other cheap TVs that are basically same as the skyworth?
Sorry, I have none.
@@tevzTVTevatronics OK thanks anyways... can you make a video and explain from where the power goes in the border and where it runs from the plug in to the led panel and where or what the normal volts are supposed to be for capacitors and diodes and the bigger transistors ? I'm trying to figure out how or where to find the drivers for led are by just looking at the power board... I'll watch them again and try to figure out the volts.. I just with there was a video on tvs that explain what each section or part does and how to find them... but thanks keep the videos Coming I like them....cheerz
Sir, will you make me your Disciple
Pls response me God bless you
Hi Mr T. Can you please confirm that some tvs have type A and B strips inside due to centre strip being less brightness. I checked each strip to see centre strip is less bright and takes half the current . This is normal right?
Class A B Im not sure
@@tevzTVTevatronics my guess is different strips at different locations to even out brightness on some designs. Keep happy MR T.
Hello sir i have an lg 49 inch nanocell tv, it has standby light but no response from the power button, sometimes after a few minutes of pressing the tv tries to turn on and the standby light flashes and goes out like the tv is on, but no backlight , no image, no 5v usb output , the 13v from the psu is there and 3.3v is there on the main board and theres voltage on most of the inductors on the main board , the cpu is the only thing warming up, it gets hot as soon as i plug the power cable in , theres no shorts on the main , how else can i diagnose the problem ? Thankyou for any help sir. Reace , UK
Hi Tevz, I’ve one small question about backlight section of LCD, LED Tv or Monitors.
I’ve seen many people ignore the DIM/Adjustable pin connection while they’re adding an Inverter Board (External) they just use Vcc, Gnd & Enable connection. So I’m very much curious to know about that DIM connection like from where this signal is coming from, which IC generates DIM singal and why we do not use it while adding inverter module.
Thank you very much 🙏🏻
Dim is for the adjustment of the led brightness. It's important to connect it. DIM, BL adjust are similar.
May musang
Ua40h5303ar samsung 40 inch tv led drivers cannot find the problem thanks
how much for cat? :)
Hi mister tevez can please you give us the link where to get schematic diagram for this model and also why you didn't change the IC
I don't have.
POR QUE NO CAMBIASTE EL DRIVER?
No available IC driver. IF there is a way to make it works without replacing the damaged component. Do it.
رغم انني لا افهم اللغة الانجليزية ،لقد تبين لي بانك قمت بعمل دكي جدا
اما سؤالي الان هو:
هل بدا عملك انطلاقا من datasheet اولا؟؟
و شكرا من المغرب
Too complicated repair this one. Well done Sir
Yes, thanks
@@tevzTVTevatronics can you please make another video with more detailed information to solve this kind of problem
@@daba06 count me on.
An SLC2013M driver IC is about a half-USD (50 cent) part, why not fix it the right way? There must be electronic stores there, or if you fix this many TVs you should have one in stock or lying around on a donor board. Except with companies such as Apple for which parts are not available, a patch job like this is not an acceptable repair and certainly not guaranteed to last for long.
Yes it's a very cheap ic, the problem is not available in my area, if I buy online it's take 3 months to arrive.
10R0 smd resitor foulted
Why did he switch to an analogue multimeter?
Other than that I don't have a balls what's going on here.
Measuring on to off voltage. Analog meter is the right tool.
@@tevzTVTevatronics I was thinking that myself and have been looking for a cheap one. The digital multimeters are not able to pick up those quick changes. I thought I was mistaken for thinking this but now your video has confirmed my thoughts.