Very informative video, thank you. I tried my NutriBullet (new) from Amazon and after 5 seconds of functioning it died. After 2 minutes or so of letting it rest, I tried it again and it worked for a few more seconds. I think I might have the same issue.
Hey Mike. I used the prob leads to sort of pry the plastic wire sheathing closest to the switch. You could also skin a tiny section from the wire. Good luck.
Hi Miro. I had already fixed before I did the guide. Taking for granted you have experience with soldering, simply melt the solder on the two leads of the old part, then solder in the new. Try not to keep the soldering iron on the new part too long.
Mi procesador no es marca nutribuler es faberware , y al accionarla hace ruido el motor pero no funciona. creo que esta amarrado el motor , Como la arreglo?
At the end of the vid I show the brand and part number. I would Google or search Amazon. I show my invoice as well if you want to use the same company I did. Good luck.
Hello Joe, I have a question if you don’t mind giving a tip or tell me what might be the issue. My Nutribullet when turn on first goes fast then slow and sometimes it stops working , do you think it might the same issue ? Thanks in advance.
Hey ElChilie. Do this. Try using with a half a cup of water. If the issue still happens, sounds like something internal to the motor is the issue. That’s bad. 😬 If it works fine with the water, then you are probably over filling the cup. There is a larger cup you can get. The limiter is designed to shut the motor down when it overheats so sounds like that is working properly. I believe the instructions say not to run for more than a minute continuously. Hope that helps.
![ฉันจะ "แพรี่" ให้หมด - ผู้แข็งแกร่งที่สุดในโลกอยากจะเป็นนักผจญภัยให้ได้ - ตอนที่ 04 [ซับไทย]](http://i.ytimg.com/vi/PvmuP8y9IPk/mqdefault.jpg)
Very informative video, thank you. I tried my NutriBullet (new) from Amazon and after 5 seconds of functioning it died. After 2 minutes or so of letting it rest, I tried it again and it worked for a few more seconds. I think I might have the same issue.
Hey Mike. I used the prob leads to sort of pry the plastic wire sheathing closest to the switch. You could also skin a tiny section from the wire. Good luck.
Very informative!
PLEASE HELP ME, , WHERE TO FIND A VIDEO THAT SHOWS HOW Base Disassembly OF THE Ninja Nutry Slim QB3000 SERIES. PLEASE HELP TO FIND
Really struggling to get my meter probes into the actuator to test. Is there a trick to this?
just what i was looking for where can i get the thermal protector
Very helpful.., thank you
You didn't show us how to replace the thermal
Hi Miro. I had already fixed before I did the guide. Taking for granted you have experience with soldering, simply melt the solder on the two leads of the old part, then solder in the new. Try not to keep the soldering iron on the new part too long.
Thank you sir.. I will try that
How to get the power chord replaced.
Mi procesador no es marca nutribuler es faberware , y al accionarla hace ruido el motor pero no funciona.
creo que esta amarrado el motor ,
Como la arreglo?
At the end of the vid I show the brand and part number. I would Google or search Amazon. I show my invoice as well if you want to use the same company I did. Good luck.
Hello Joe, I have a question if you don’t mind giving a tip or tell me what might be the issue. My Nutribullet when turn on first goes fast then slow and sometimes it stops working , do you think it might the same issue ?
Thanks in advance.
Hey ElChilie. Do this. Try using with a half a cup of water. If the issue still happens, sounds like something internal to the motor is the issue. That’s bad. 😬 If it works fine with the water, then you are probably over filling the cup. There is a larger cup you can get. The limiter is designed to shut the motor down when it overheats so sounds like that is working properly. I believe the instructions say not to run for more than a minute continuously. Hope that helps.
Joe Bailey
Thanks.I will try that and I ‘ll let you know what happens.
It might be the brushes. There is black dust coming out from the bottom. Can they be replaced ?
what's the part number for that thermal switch
Google search 7am026a5 Thermal Switch.
Joe Bailey is this for all nutra bullets or just the majority. Should they all have the same components
❤