Thanks dude Ive been struggling with another video for days until I got fed up, found yours and got in 20 mins brilliant. Good to see a fellow countryman doing vids. Im in Mayo
A company wants to implement a large number of WAPs throughout its building and allow users to be able to move around the building without dropping their connections Which of the following pieces of equipment would be able to handle this requirement? (A). A VPN concentrator (B). A load balancer (C). A wireless controller (D). A RADIUS server Could you please help me find the correct answer to the question above?
Hi Birol, have you looked up info regarding the Wireless LAN controller(WLC). These typically control many lightweight WAP(wireless access points). WLC are also responsible for Radio Frequencies management, association and roaming management (devices moving from one AP to another). Hope this helps!
Hi Raju, I haven't created one like this before in Packet Tracer. I'm not sure if you've already tried this but I'll keep this in mind when I'm creating new content though.
This is very specific tutorial I stumbled across seems very well done, originally I was looking for general wireless lan controller info because I wanted to buy some second hand cisco access points from an auction at a university, however i really enjoyed this tutorial so my question is how do I start learning about this stuff is their a class you recommend and can I get certified in this field?would
Hi @Joshua, glad the videos helped. If you're looking to learn more on Wireless and other networking technologies - a great first step in my opinion would be to check out the various free resources located at www.netacad.com/
I configured DHCP pools in a L3 Switch.. but hosts connected to APs, cannot get the right IP addresses! In simulation mode, I saw that switch ports that are connected to APs are blocked by STP!
please i am having a very serious challenge. I am learning cisco networking with packet tracer. So, i was building a topology which was connecting just fine with trunks created, vlans created etc. But now i wanted to add wireless capabilities to the network, when i introduced a wireless controller to the network with ip address and gateway still yet i can't either ping to the controller or log into it from a p.c weither connecting directly to the controller or through a switch
Hi @Chukwuma, as you are using VLANs you will need to add additional configuration to your network - for example, wherever you connect up your WLC to your switch - good practice to make this port a trunk port (to allow more than one VLAN) to cross this. Also, you will likely need to add more config to your WLC - such as new WLANs (mapping back to a wired VLAN) - a gotcha here is to ensure when you create a new wlan that you remember to enable each (there's a checkbox to do this). Finally, on the WLAN controller interface, the tabs I would recommend you explore are: WLANs & Controller (Internal DHCP Server is on the left within Controller interface). One last tip i would give you is to get used to using the fast forward time button whilst you navigate and make changes in your WLC. Good luck with your network config! Thanks, Greg
Hi Dawood, I've just done a quick test on PT 8.1.1 on MacOS and it works (using the WLC 2504). Couple of things to check: After you have connected for the first time and completed setup initial configuration parameters. Do you ensure to add the IPADDRESS - note the s for security is important here. By trying to connect using HTTP it will no longer work and you get server reset connection. Also, during the initial configuration - did you ensure to put in the correct Management IP address of the WLC (important that this is checked/correct also). All the best, Greg
Hey do you know if there's a limit to how many APs you can connect to the same WLC? I have a total of 8, only 7 registered, they are all in the same vlan.
Hi @TheBoostedDoge - i don't believe i've tested this many APs before. As good as Packet Tracer is, at the end of the day it's a simulator and I've come across different limitations with some protocols in the past. The next time I'm configuring wireless I'll experiment. Perhaps someone else watching may add in here their own experience too - all the best with the labbing...
Hi, the WLC device that I used in the video is the WLC-2504 - this can be found in the menu by selecting wireless devices and by picking the 2504 in this case. All the best, Greg
🔰 Hiya Greg, Can I provide a tidbit of constructive criticism...You video here, sounds like you’re in an empty room. I’d get an area rug or hang some sound absorption materials on your walls... @Greg South
![ออกพรรษาน้ำตาหล่น - แอน อรดี [OFFICIAL MV]](http://i.ytimg.com/vi/PFZtOcY9ONA/mqdefault.jpg)
Thanks dude Ive been struggling with another video for days until I got fed up, found yours and got in 20 mins brilliant. Good to see a fellow countryman doing vids. Im in Mayo
Great stuff! Glad the video helped. Mayo is a great spot
Your way of teaching is Awesome, Thanks
Thanks for the feedback @Hasan
I found your video very helpful thanx a lot bro keep it up!!!
Pleased that it helped Kirubel! Thanks for viewing, Greg
Great video, well Explained!!!
Glad it helped!
thanks a lot, you are the best I'm studying IT ENGINEERING you did help me a lot
Thank you, a lot, for the experience.
You're welcome
nice video
Thanks for the visit
This video was mush helpful to my studies bro
Thanks for the feedback Muhammad. Glad the video helped, Greg
Thank you so much.. I hv got many answers and solutions..
Great Muhammad👍
great teaching thanks you
Glad the video helped
Great!!! well done!
Thanks Justine
Great tutorial, and very well explained.
Glad it was helpful Paul!
great, keep going)
Thanks @Abdurahim for the feedback - hoping to do more videos soon!
Grey big 👍
A company wants to implement a large number of WAPs throughout its building and allow
users to be able to move around the building without dropping their connections Which of the
following pieces of equipment would be able to handle this requirement?
(A). A VPN concentrator
(B). A load balancer
(C). A wireless controller
(D). A RADIUS server
Could you please help me find the correct answer to the question above?
Hi Birol, have you looked up info regarding the Wireless LAN controller(WLC). These typically control many lightweight WAP(wireless access points). WLC are also responsible for Radio Frequencies management, association and roaming management (devices moving from one AP to another). Hope this helps!
Hi Greg- Could you please share one with multi sites (With Different Network) with centralised WLC.
Hi Raju, I haven't created one like this before in Packet Tracer. I'm not sure if you've already tried this but I'll keep this in mind when I'm creating new content though.
This is very specific tutorial I stumbled across seems very well done, originally I was looking for general wireless lan controller info because I wanted to buy some second hand cisco access points from an auction at a university, however i really enjoyed this tutorial so my question is how do I start learning about this stuff is their a class you recommend and can I get certified in this field?would
Hi @Joshua, glad the videos helped. If you're looking to learn more on Wireless and other networking technologies - a great first step in my opinion would be to check out the various free resources located at www.netacad.com/
I configured DHCP pools in a L3 Switch.. but hosts connected to APs, cannot get the right IP addresses! In simulation mode, I saw that switch ports that are connected to APs are blocked by STP!
good job
Thanks so much budy. I have a question, we can conect other device direct on the WLC by wifi ? like you did with access point ?
please i am having a very serious challenge. I am learning cisco networking with packet tracer. So, i was building a topology which was connecting just fine with trunks created, vlans created etc. But now i wanted to add wireless capabilities to the network, when i introduced a wireless controller to the network with ip address and gateway still yet i can't either ping to the controller or log into it from a p.c weither connecting directly to the controller or through a switch
Hi @Chukwuma, as you are using VLANs you will need to add additional configuration to your network - for example, wherever you connect up your WLC to your switch - good practice to make this port a trunk port (to allow more than one VLAN) to cross this. Also, you will likely need to add more config to your WLC - such as new WLANs (mapping back to a wired VLAN) - a gotcha here is to ensure when you create a new wlan that you remember to enable each (there's a checkbox to do this). Finally, on the WLAN controller interface, the tabs I would recommend you explore are: WLANs & Controller (Internal DHCP Server is on the left within Controller interface). One last tip i would give you is to get used to using the fast forward time button whilst you navigate and make changes in your WLC. Good luck with your network config! Thanks, Greg
after securing the http to https, i still have server reset connection? im using 8.1.1 on macOS
could you help pls
Hi Dawood, I've just done a quick test on PT 8.1.1 on MacOS and it works (using the WLC 2504). Couple of things to check: After you have connected for the first time and completed setup initial configuration parameters. Do you ensure to add the IPADDRESS - note the s for security is important here. By trying to connect using HTTP it will no longer work and you get server reset connection. Also, during the initial configuration - did you ensure to put in the correct Management IP address of the WLC (important that this is checked/correct also). All the best, Greg
Hey do you know if there's a limit to how many APs you can connect to the same WLC? I have a total of 8, only 7 registered, they are all in the same vlan.
Hi @TheBoostedDoge - i don't believe i've tested this many APs before. As good as Packet Tracer is, at the end of the day it's a simulator and I've come across different limitations with some protocols in the past. The next time I'm configuring wireless I'll experiment. Perhaps someone else watching may add in here their own experience too - all the best with the labbing...
how can i get the wlc image sir ??
Hi, the WLC device that I used in the video is the WLC-2504 - this can be found in the menu by selecting wireless devices and by picking the 2504 in this case. All the best, Greg
256 likes, per subnet lol
🔰 Hiya Greg,
Can I provide a tidbit of constructive criticism...You video here, sounds like you’re in an empty room. I’d get an area rug or hang some sound absorption materials on your walls... @Greg South
Thanks CiscoLadder! I'll keep an eye out for a rug - Hope you found the content useful. Thanks, Greg
Great video, well Explained!!!