Muy bien 👍 un consejo dirige la salida del vapor hacia arriba 🔼 para que nadie que pase por cerca por donde expide el vapor caliente, no pase un accidente, después que ya hizo su trabajo el vapor dirigelo con el tubo doblalo para arriba ⬆️ si no es inconveniente a tu invento. Felicidades!
Teve um Brasileiro que teve essa mesma idéia, criou uma carrocinha com motor a vapor e ele dirigiu por vários km inclusive fazia até comida com a lenha que ele abastecia o veículo, parabéns pela criatividade.
Muito bem, tenho um equipamento a vapor que trabalha com velocidade 110 giros e produz 20 cv de força, toca uma moeda de cana de açúcar, comprei já usada com 40 anos trabalhando com o antigo dono e comigo mais 20 anos e só gastou graxetas, e o vapor era gerado como próprio bagaço da cana. Hoje está parado pois à idade chegou para mim e não encontrei ninguém para dar continuidade, fabricava cachaça. Parabéns pelo trabalho.
Se ele criasse um jogo de engrenagens em vez de ligar diretamente o eixo da roda ao eixo do gerador, conseguiria aumentar a rotação do dínamo, embora precisasse aumentar um pouco a potência do motor também. Uma boa ideia também seria usar o motor acoplado a uma pequena bomba hidráulica para bombear água.
Since i started watching people trying to create generator for years this is the one that have really caught my attention. keep it up dont stop upgrading soon the world will need you to buy it in large quantity
condensors serve no purpose on reciprocating piston engines intended for running on high pressure steam. one. they produce a VACUUM in the cylinder. rather than a force PUSHING on it, you have a mere 14.7 psi at best of atmospheric pressure acting on the other side of the piston. aka "newcommen" or "watts" atmospheric steam engine... extremely inefficient. very low power outputs. two, by producing a vacuum in the cylinder, on the exhaust stroke, rather than compress the remaining contents, to fill the clearance volume, so fresh entering steam isnt wasted in filling it, theres nothing in there to compress... so on every stroke, a large proportion of steam is wasted in doing nothing but filling this clearance volume. leaving the fins on the cylinder just promotes condensation in the cylinder, with inevitable loss of power... the standard method is to at least insulate them, better yet, steam jacket them, or place them within the boiler/furnace itself. its called "rejected heat". and finally, steam itself is a dead-end of inherent inefficiencies, mostly due to the latent heat of phase change. the energy required to take it from boiling to actual steam cannot be recovered. yes, you can preheat the feed water to a degree, yes, you can preheat the air for the furnace, but you still can never reclaim 80% of the energy used in boiling that water. its gone. no matter what you do. thats ignoring the losses in the boiler, in the pipework, etc... no steam engine can ever beat 12% efficiency, give or take. on a small scale, with plenty of alternatives, steam is a dead end, a waste of time. better to look at ericsson/brayton cycles, far superior implementations of the "stirling engine". i give credit for trying, and getting one to run, but really, if you had any idea about teh physics of steam, you would know its utterly pointless. unless you are trying to drive a 5MW+ generator... in which case its main benefit is that its relatively compact as compared to anything relying on hot air... at that point, its about the only reasonable solution.
Parabéns pelo magnífico conteúdo. Tenha uma vida repleta de bênçãos e muitas conquistas! Que a mente continue sempre criativa e ativa. Felicidades sempre!!
Maestro fue una excelente clase de fisica, lastima que en las escuelas no dan la,parte practica, tambien aprendi areutilizar metales, cortar y soldar, sin olvidar el diseño para replicar un equipo clasico, BRAVO
vc podia ajudar pessoas que não tem acesso a energia fabricando algum desses seus inventos, que por sinal são bem interessantes e parecem bem construídos.
Genialidad Pura..!! Sos un capo mi amigo, ojalá tuviera un vecino como vos. Tengo como meta de vida fabricar un motor que entregue al menos 5 hp con una buena caldera de 1 metro cúbico para empezar. Tienes como proyecto crear algo más grande y potente..? Se que cuesta dinero. Si esa es tu intención, espero que lo logres porque me encantaría verlo..❤
Parabéns ótimo trabalho se for possível fazer um vídeo daquela valvula onde entra e sai o ar eu ainda não consegui entender apesar de que você explica em outros videos
Мужик ничего не изобрёл. Рукастый, головастый, не спорю. Но он просто воссоздал принципиальную схему парового двигателя. Молодец. А про котел - для такой схемы и этого хватит. А понадобится - заморочиться и многотрубный сделает.
Professor, e se voce usar uma lente de tela de tv para gerar o calor necessário? O canal manual do mundo ja fez uma experiência com uma lente gigante, o calor chega a 600 graus, tem ate que usar oculos de proteção... Mas dá para fazer também com uma parabólica com espelhos, o calor grado é grande também... Aí não precisaria ir atrás de lenha, seria um upgrade na engenhoca 😉
Felicidades profesor y gracias por compartir este lindo video, solo una consulta; por favro me puede explicar qué es lo que exactamente hace el aceite? es decir, que papel juega y porque esta en serie con el vapor de agua?? no entiendo eso.
Good job man i loved it so much and i loved its sound i imagine if i beside it and feel bored i stand beside it and say tooot like the train i would laugh and my sadness will go away and that a great benifit beside electricity 😂❤❤❤❤❤ Good luck go ahead bro
Ótimo projeto, você já testou usar condensador? Com isso consegue-se reduzir a perda de água, e opcional: o calor residual poderia alimentar motores stirling.
Your design of a single-piston steam engine is awe-inspiring. Everything was carefully thought out and checked, you even installed a safety valve and lubrication of the cylinder, piston and timing mechanism. You have soldered six rectifier diodes correctly and constructed a three-phase rectifying bridge, because the BLDC motor generates three phases in the generator function. Congratulations and best regards 😀.
Sempre veio aquela pergunta, se o motor de movimento perpétuo já existiu onde ele está? Quem inventou? Por que não foi utilizado para contornar a situação do desequilíbrio das forças da natureza? Pois é rapaz, vivemos em uma sociedade onde você apresenta o melhor mas a ganância sempre fala mais alto A construção do dispositivo é possível 🦅
I want to see the actually Voltage/Amperage/Wattage that something like this produces. Still, really nice work! I think I'd want the heaviest flywheel possible to keep the power a little more even but if you're hooking up anything that needs clean power you'll probably have to add a battery of some kind into the mix- maybe it doesn't matter. I love any form of DIY energy production! I think hydroelectric is my favorite means of producing power in a 'green' way, though it requires being near a continuous flow of water, or tide/wave generators which requires being on the Coast, preferably in a place where the tides are more pronounced than average.
In a cabin in the woods type situation thus would be great. You could make it a permanent installation by placing a boiler in the house (fireplace) obviously with the right precautions like a blow off valve or two, directed outside set for a safe pressure. And place your little genny in the shed. I recon it would work very well supplying light and charging small batterys ect, all while keeping the cabin warm.
Agora acopla um aquecedor solar tipo raio do sol esquentando a panela.e aí..elimina o fogo....uma antena de parabólica cheia de pequenos cacos de espelhos direcionando o raio solar para o centro, esquentando uma pequena panela ..seria melhor q fofo..pois os sol e gratis...lógico q a noite teria de ter uma bateria..mais seria legal...valeu...parabéns
Es un buena idea ,lo único que yo trataría de hacer es buscar la forma de multiplicar la fuerza del motor a vapor ,no sé si con una caja de marchas o algo ya que para avanzar más en el proyecto poder trasladar toda esa fuerza a la casa . A si como está sirve para cuatro lámparas y se ve como va perdiendo la fuerza a medida que las va prendiendo
Fiquei pensando e com esse torque ,poderia usar o aro da roda como polia e fazer a transmissão por correia....ia multiplicar a rotação e aumentar a voltagem, com o mesmo sistema
link stirling
s.click.aliexpress.com/e/_Dk5bgfD
mercadolivre.com/sec/1F8Ccxn
❤
ХАТЮ!!!😢😢😢(😍👍💋)
Muy bien 👍 un consejo dirige la salida del vapor hacia arriba 🔼 para que nadie que pase por cerca por donde expide el vapor caliente, no pase un accidente, después que ya hizo su trabajo el vapor dirigelo con el tubo doblalo para arriba ⬆️ si no es inconveniente a tu invento. Felicidades!
9 06
😅tb8@@gheorghepirtia7689
Ssiiip
Teve um Brasileiro que teve essa mesma idéia, criou uma carrocinha com motor a vapor e ele dirigiu por vários km inclusive fazia até comida com a lenha que ele abastecia o veículo, parabéns pela criatividade.
É o mesmo brasileiro
E esse cara do vídeo aí 😅😅😂😂
É ele mesmo kkkk
😂😂😂😂😂😂😂 viva brazil caraiii😅😅😅
É o mesmo Senhor 🙂
Muito bem, tenho um equipamento a vapor que trabalha com velocidade 110 giros e produz 20 cv de força, toca uma moeda de cana de açúcar, comprei já usada com 40 anos trabalhando com o antigo dono e comigo mais 20 anos e só gastou graxetas, e o vapor era gerado como próprio bagaço da cana. Hoje está parado pois à idade chegou para mim e não encontrei ninguém para dar continuidade, fabricava cachaça.
Parabéns pelo trabalho.
Onde vc mora ?? Podemos negociar ela
@@rafael32912 Ivaiporã Pr. Ela produz 900 litros aguardente por hora. Vou vender sim.
A idade chega, aí hora de tirar o pé. DEUS abençoe vc guerreiro
faz um video ai pra nos
TÔ IMPRESSIONADO PR PARDAL PARABÉNS MAS UMA VEZ NOS SURPREENDEU 😃👍👍👍👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏
PROFESSOR PARDAL BRASIL, vc é um genio(criativo), tá de parabéns. Obrigado por compartilhar a suas ideias.....
Maquina a vapor ou locomotiva. Uma engenharia de respeito parabéns
Se ele criasse um jogo de engrenagens em vez de ligar diretamente o eixo da roda ao eixo do gerador, conseguiria aumentar a rotação do dínamo, embora precisasse aumentar um pouco a potência do motor também. Uma boa ideia também seria usar o motor acoplado a uma pequena bomba hidráulica para bombear água.
Since i started watching people trying to create generator for years this is the one that have really caught my attention. keep it up dont stop upgrading soon the world will need you to buy it in large quantity
it's a proven concept
bro thinks we are in 1712
You're about 300 years late on that thought.
Amin semoga terjawab yang maha kuasa.
@@illbeyourmonster3591 uhhmmm no we are heading to ww3 if not already started. but thats up to history writers in 50 years
Amado Professor Pardal, sempre trazendo algo util e tecnico❤❤❤❤
Mestre demais. Faz a cousa parecer simples e fácil. Parabens.
Have you thought about adding a condenser to recirculate your now preheated water?
Great build as always
Esse modelo com condensador é interessante. Você tem um caminho? Obrigado
@@pc9238 da pra fazer de duas formas, ou ele troca calor do vapor com outro liquido, ou um dissipador de calor com o ar
condensors serve no purpose on reciprocating piston engines intended for running on high pressure steam.
one. they produce a VACUUM in the cylinder. rather than a force PUSHING on it, you have a mere 14.7 psi at best of atmospheric pressure acting on the other side of the piston. aka "newcommen" or "watts" atmospheric steam engine... extremely inefficient. very low power outputs.
two, by producing a vacuum in the cylinder, on the exhaust stroke, rather than compress the remaining contents, to fill the clearance volume, so fresh entering steam isnt wasted in filling it, theres nothing in there to compress... so on every stroke, a large proportion of steam is wasted in doing nothing but filling this clearance volume.
leaving the fins on the cylinder just promotes condensation in the cylinder, with inevitable loss of power... the standard method is to at least insulate them, better yet, steam jacket them, or place them within the boiler/furnace itself. its called "rejected heat".
and finally, steam itself is a dead-end of inherent inefficiencies, mostly due to the latent heat of phase change. the energy required to take it from boiling to actual steam cannot be recovered. yes, you can preheat the feed water to a degree, yes, you can preheat the air for the furnace, but you still can never reclaim 80% of the energy used in boiling that water. its gone. no matter what you do. thats ignoring the losses in the boiler, in the pipework, etc... no steam engine can ever beat 12% efficiency, give or take.
on a small scale, with plenty of alternatives, steam is a dead end, a waste of time. better to look at ericsson/brayton cycles, far superior implementations of the "stirling engine".
i give credit for trying, and getting one to run, but really, if you had any idea about teh physics of steam, you would know its utterly pointless.
unless you are trying to drive a 5MW+ generator... in which case its main benefit is that its relatively compact as compared to anything relying on hot air... at that point, its about the only reasonable solution.
@@paradiselost9946 so old mate built a steam engine that works and you’re trying to shit on him , perhaps you should crawl back under you’re rock
@@paradiselost9946 You'r a bloody wet blanket. What he built is great, and i would use it in my off grid shack.
Parabéns pelo magnífico conteúdo. Tenha uma vida repleta de bênçãos e muitas conquistas! Que a mente continue sempre criativa e ativa. Felicidades sempre!!
É estes tipos de vídeos que procuro assisti no youtube parabéns !!!
parabéns professor pardal ótima sua invenção. Perfeita
Nadie cómo nuestro querido y estimado professor Phardal que nos cultiva con su infinito conocimiento!!!🍷🗿
Muito obrigado!!!🇲🇽🇧🇷
O rei do motor a vapor caseiro Joel !
Vc é o cara,vc tem construir um carro a vapor,vai ser maravilhoso parabéns.
Muito legal processo antigo de caldeira, parabéns 👏👏👏🇧🇷
Um construtor competente !!! Parabéns !!!
Conceito muito antigo mas sempre bonito de se ver.
Parabéns.
SHOW DE CRIATIVIDADE E CAPRICHO 👏👏👏👏👏👏
Parabéns pelo trabalho 🎉
você e o brasileRO MAIS INTELINTE EU VI
Depois de muitos anos inventando a máquina a vapor, este respeitado cavalheiro começou a produzir a máquina a vapor novamente 😄👍
Muito bom, apesar de não ter um uso prático, é bastante instrutivo, gostei.
VOU ASSISTIR DE NOVO GOSTEI DEMAIS AMIGO
Maestro fue una excelente clase de fisica, lastima que en las escuelas no dan la,parte practica, tambien aprendi areutilizar metales, cortar y soldar, sin olvidar el diseño para replicar un equipo clasico, BRAVO
Do jeito que o mundo vai indo vamos precisar disso no futuro pode crer
O melhor do TH-cam ❤
Es reconfortante ver que aún habrá gente que mantenga la civilizacion cuando caiga el meteorito 😅. Gran trabajo 👍🏼
Parabéns pelo seu trabalho top demais ❤
Very good professor, compliments from the kingdom of Eswatini southern Africa
vc podia ajudar pessoas que não tem acesso a energia fabricando algum desses seus inventos, que por sinal são bem interessantes e parecem bem construídos.
Genialidad Pura..!!
Sos un capo mi amigo, ojalá tuviera un vecino como vos.
Tengo como meta de vida fabricar un motor que entregue al menos 5 hp con una buena caldera de 1 metro cúbico para empezar.
Tienes como proyecto crear algo más grande y potente..?
Se que cuesta dinero. Si esa es tu intención, espero que lo logres porque me encantaría verlo..❤
Fantastic video. I love seeing steam engines like this.
Parabéns ótimo trabalho se for possível fazer um vídeo daquela valvula onde entra e sai o ar eu ainda não consegui entender apesar de que você explica em outros videos
Maravilhoso esse projeto, parabéns
That is just too bloody cool mate, freaking excellent! Well done
Умный мужик, отличное изобретение 👍👌💪👏👏👏
Только фуфло толкаит
Бред котел на 1-2 минуты пара.
Чё там умного если самое сложное не может сделать паровой котел.
Мужик ничего не изобрёл. Рукастый, головастый, не спорю. Но он просто воссоздал принципиальную схему парового двигателя. Молодец.
А про котел - для такой схемы и этого хватит. А понадобится - заморочиться и многотрубный сделает.
Это вы про Джеймса Уатта еще не знаете. В учебнике физики за седьмой класс много магов и волшебников.
А что он изобрёл?не понял!😂😂😂
Muito genial meu amigo / great idea /Parabens
El algoritmo de TH-cam está enamorado de este canal 😍👍
ótimo trabalho....parabéns!!!
Show meu amigo .gambiarra que até estrangeiros manda um joinha.
Manda o site dessa lima rotativa parece de boa qualidade .Grande abraço
Professor, e se voce usar uma lente de tela de tv para gerar o calor necessário? O canal manual do mundo ja fez uma experiência com uma lente gigante, o calor chega a 600 graus, tem ate que usar oculos de proteção... Mas dá para fazer também com uma parabólica com espelhos, o calor grado é grande também...
Aí não precisaria ir atrás de lenha, seria um upgrade na engenhoca 😉
Absolutely fantastic,,,, now I want to make one. Well done, I'm very impressed 👏
Se todos usassem a cabeça para idéias criativas o mundo seria bem diferente, parabéns amigo pela idéia....
Wow, that is a great piece of functional art.
Nice work 👌👍😎🔥🔥🔥
Felicidades profesor y gracias por compartir este lindo video, solo una consulta; por favro me puede explicar qué es lo que exactamente hace el aceite? es decir, que papel juega y porque esta en serie con el vapor de agua?? no entiendo eso.
Good job man i loved it so much and i loved its sound i imagine if i beside it and feel bored i stand beside it and say tooot like the train i would laugh and my sadness will go away and that a great benifit beside electricity 😂❤❤❤❤❤
Good luck go ahead bro
Bom dia amigo❤❤
MESMO QUE NÃO GERASE ENERGIA ;SERIA UMA MAQUINA INTEREÇANTE DEMAIS LINDA MAQUINA
Ótimo projeto,
você já testou usar condensador?
Com isso consegue-se reduzir a perda de água,
e opcional: o calor residual poderia alimentar motores stirling.
Hadir pak bos,dari balam Riau mantap sekali buat insfirrasinya top👍
Professor Pardal ... complimenti per il lavoro ... sai che i miei esperimenti li faccio dai rottami ...
Un saluto
Brilliant piece of DIY. I like the exhaust valve setup and timing. :)
And again amazing videos I love your steam engine single cylinder using an old bike wheel amazing!!!!😢😅😂😂😊
Excellent job, simple design but works well 👍
Bonjour, très belle réalisation, bravo, ça fonctionne ! et l'on apprécie le travail ! encore super bravo. Cordialement.👍
True engineering ❤❤❤❤❤ love from india
um motor a vapor convencional :D
Muito interessante prof
Sensacional 👏👏👏👏👏👏👏
Your design of a single-piston steam engine is awe-inspiring. Everything was carefully thought out and checked, you even installed a safety valve and lubrication of the cylinder, piston and timing mechanism. You have soldered six rectifier diodes correctly and constructed a three-phase rectifying bridge, because the BLDC motor generates three phases in the generator function.
Congratulations and best regards 😀.
EU VIAJARIA SO PRA TE CONHECER, FERA DEMAIS!
Sempre veio aquela pergunta, se o motor de movimento perpétuo já existiu onde ele está?
Quem inventou?
Por que não foi utilizado para contornar a situação do desequilíbrio das forças da natureza?
Pois é rapaz, vivemos em uma sociedade onde você apresenta o melhor mas a ganância sempre fala mais alto
A construção do dispositivo é possível 🦅
Un saludo desde Argentina.
bacana ! fiz um parecido so que a caldeira usei uma panela de pressão grande de 7 litros e o gerador usei um estator e um magneto de cg titan !
Olha se voçe fazer pra vender fala ai pra Nós mas ficou shom meu amigo👏👏👏👏👍👍
Felicidades chicos,se los quiere un monton !!!
Parabéns!
Muito bom!
Nice job buddy. works great free Electricity ⚡️⚡️all the way from Kentucky. 💯👀👍
That was very good. I enjoyed that.😁😁😁😁👍👍👍👍👍👍
You make this steam engine so easy and simple I love your video you are too much
Muito top, parabéns! seria viável fazer com aquecimento solar?
You are the best professor 😊 Could you try with solar to boil the water please ?
Muito legal ❤parabéns
Muy buena idea profesor ... Solamente que no todos sabemos hacerlo , de todos modos gracias por la idea .
Muito bom seus vídeos, parabéns deus abençoe, qual estado vc mora ?
Ensina como fazer um gerador de energia com a água do rio
Estou Inscrito
video yang sangat menarik. Saya suka ini.
Parabéns pardal.dimais
Tomah !!!! 😮 Excelente, muy bien 10 ...🎉🎉🎉
Essa idéia é GENIALLLLLLLL!!!!!!!
Parabens pelo projeto!
Great tech. I m ur new subscriber.
MEU AMIGO VECE É UM CRANEO !! CARARAMBA!!PARABÉNS SUCESSO SEMPRE
top demais mano muito bom funciona muito bem
Muito criativo🙏🙏🙏🙏
Excellent! A great example simplistic, but usefulness, more!
Great Build,How many dc volts does it put out.
I want to see the actually Voltage/Amperage/Wattage that something like this produces. Still, really nice work! I think I'd want the heaviest flywheel possible to keep the power a little more even but if you're hooking up anything that needs clean power you'll probably have to add a battery of some kind into the mix- maybe it doesn't matter. I love any form of DIY energy production! I think hydroelectric is my favorite means of producing power in a 'green' way, though it requires being near a continuous flow of water, or tide/wave generators which requires being on the Coast, preferably in a place where the tides are more pronounced than average.
Wow Very Nice Good Job Dear 👍
God Bless You All Best Wishes To You ❤️🙏🏻❤️
In a cabin in the woods type situation thus would be great. You could make it a permanent installation by placing a boiler in the house (fireplace) obviously with the right precautions like a blow off valve or two, directed outside set for a safe pressure. And place your little genny in the shed. I recon it would work very well supplying light and charging small batterys ect, all while keeping the cabin warm.
He makes it look so easy
Thats crazy awesome 👌 thanks for the video, great job. Thumbs up bud🎉🎉🎉
Agora acopla um aquecedor solar tipo raio do sol esquentando a panela.e aí..elimina o fogo....uma antena de parabólica cheia de pequenos cacos de espelhos direcionando o raio solar para o centro, esquentando uma pequena panela ..seria melhor q fofo..pois os sol e gratis...lógico q a noite teria de ter uma bateria..mais seria legal...valeu...parabéns
Güzel oyuncak.. Buharlı bütün yapımları severim.. Özellikle dev lokomotifleri .. Türkiye/İZMİR den selam ve sevgiler..
MAGNÍFICO ❤
Guy puts 'Uncle Ted' to shame. He is an artist. 😊
Impressive, how did you calculate your valve timing?
Es un buena idea ,lo único que yo trataría de hacer es buscar la forma de multiplicar la fuerza del motor a vapor ,no sé si con una caja de marchas o algo ya que para avanzar más en el proyecto poder trasladar toda esa fuerza a la casa .
A si como está sirve para cuatro lámparas y se ve como va perdiendo la fuerza a medida que las va prendiendo
Fiquei pensando e com esse torque ,poderia usar o aro da roda como polia e fazer a transmissão por correia....ia multiplicar a rotação e aumentar a voltagem, com o mesmo sistema