Congratulations for your video!! Very nice job, you are a professional, jeje... I will try to instal my new yamaha led plus this week, i hope to do it well... i have doubts, but i have to work in my motorbike to solve it. Thanks for your time, continue in this way. I have a question for you... have i got the same with the front turn signals?? Thanks!!
Perfect vid...yesterday i put the front led plus indicators and alla perfect...today i ride my bike and the left flash was blink only 4 leds...do you know why became that?
Anyone have problems with these indicators with condensation?? There is no weephole and i cant even see a way of geetting the lenses off to clean em out?
They should be in the set with LED blinkers. www.cmsnl.com/products/led-blinker-rear-plus_ymeflb2r20/?locale=nl-nl&gad_source=1&gclid=Cj0KCQjwltKxBhDMARIsAG8KnqUp_0PDDQXMDhEaXImY2MpvHz0u6ODqI1FnICxBOpsLKScajSKsdlgaAi0VEALw_wcB
Have you had problems with the LED afterwards? Mine right LED is glowing weak. 2-3 of the leds are very bad. I also got mine installed 2 years go in at a Yamaha dealer
Hallo ik heb een vraagje ik hoop dat je mij kan helpen. Ik heb deze ook op mijn motor maar ik wil nog alleen de knipperlichten ervan blijven gebruiken. Kan ik zomaar de kabels verwijderen van de dagrij verlichting/achterlichten? Zoja, welke kleur kabels dan precies. Sorry ben niet zo technisch maar wil het graag zelf doen :p
Hoi. In theorie heb je gelijk, het loskoppelen van de kabels van de achterlichten zou moeten werken. Helaas kan ik je niet helpen met de kleuren van de kabels omdat ik het simpelweg niet meer weet, ik heb deze motorfiets 6 jaar geleden verkocht.
What seat do you have on your bike, is that the original factory seat? It looks different and nicer than the factory Yamaha seat here in the USA. Thanks
It is accessory yamaha OEM Comfort seat, but it only looks nice, in fact, it is harder and uncomfortable than the factory one, the worst spent 250 euros ever 😉
Hey! Thanks so much for this video - really helpful! Just one quick question.. is there any reason why you don't add the resistors on the blinker-side of the connectors instead of cutting cables in the motorcycle? I'm pretty new to this so would prefer to not cut any cables on the bike.. :-)
You can install resistors on the blinker cables, but if you want to disassemble the blinkers later or the entire tail tiddy, you will not squeeze the resistors through the holes in the housing. cheers, ride safe.
I have the same lights on a new machine now - i wonder if i can just use the rear brake lights without the position lights ... just brake lights and blinkers.. is that possible if i leave the blue wiring disconnected ?
Question: 7:49 "Position Light" I've never heard this term in brake or signal wiring. What exactly is the 'Position Light' wire for ?????? Pretty sure it's the 'Tail Light' wire ! Thanks.
Można. Miałem oporniki, wstawiłem przerywacz do kierunków LED i oporniki wymontowałem. Działa tak jak powinno i trochę mniej śmieci poupychane za plastikami.
Ok MOT right, sorry still sleepy, I had no problems with MOT in Poland, according to yamaha they are street legal, but every country have different lows, in the Netherlands there is no MOT for bikes, only for cars.
hey can you sell me your original oem clear turn signals. i looked on ebay but no luck. here in usa all the tracer 900 2016 and up only got the orange turn signals from the 2006 yamaha r6
Come on man, use the search browser it cost 1 min to find. www.cmsnl.com/products/led-blinker-front-plus_ymeflb2f10/?locale=nl&gclid=CjwKCAjw7J6EBhBDEiwA5UUM2rCuD-OJUtSYYNRK9P3ug9abzNAGSciV323anIGayteNUHol03m3RxoCZ2wQAvD_BwE www.ebay.de/itm/152304669386?hash=item237610d2ca:g:JK8AAOSwMVdYG3UB
I did. But I'm not one for putting links on others channels. If you check my channel for the video, you'll find a recent one on it. Same model and year as yours. Cheers n RSOT >:)
Thanks Andy. That really helped alot
Thanks Andy, Im ordering the new T1200 with those instead. they looks cool.
You did such a great job... One day I'll dare and try to do this myself to my MT-07.
Thanks, you can do it, it's not a big deal, a little patience and everything will go just fine.
Nice knife skills haha. Thanks for this video
Job well done
Merci
C’est clair 👍🏻
I didn't know where to start ... thanks for the video it was a lot of help
Perfect !!
Congratulations for your video!! Very nice job, you are a professional, jeje... I will try to instal my new yamaha led plus this week, i hope to do it well... i have doubts, but i have to work in my motorbike to solve it. Thanks for your time, continue in this way.
I have a question for you... have i got the same with the front turn signals?? Thanks!!
Should these work on a 2019 Yamaha R3?
Awesome mod bro...
Where do the waterproof connectors sell and how much,I've just fitted a tail tidy but the adapter for the led reg plate light could be better thanks.
If fitting to a 2015 on R1 leave the resistors off as they are already led, if you put the resistors in it does not work.
Perfect vid...yesterday i put the front led plus indicators and alla perfect...today i ride my bike and the left flash was blink only 4 leds...do you know why became that?
Anyone have problems with these indicators with condensation?? There is no weephole and i cant even see a way of geetting the lenses off to clean em out?
Where did you get the oval spacers between the turn signal and the license plate frame?
They should be in the set with LED blinkers.
www.cmsnl.com/products/led-blinker-rear-plus_ymeflb2r20/?locale=nl-nl&gad_source=1&gclid=Cj0KCQjwltKxBhDMARIsAG8KnqUp_0PDDQXMDhEaXImY2MpvHz0u6ODqI1FnICxBOpsLKScajSKsdlgaAi0VEALw_wcB
i would have put the resistor after the connector. so connector and light soldered together.
Have you had problems with the LED afterwards? Mine right LED is glowing weak. 2-3 of the leds are very bad. I also got mine installed 2 years go in at a Yamaha dealer
Check all the connectors if you have OEM ones, there is always a problem.
did you do the front ones too ? - need more information on that job ... Tracer 900 gt 2018
No, at the front I did have regular led ones from yamaha, because of the day lights at the hanguards.
Hallo ik heb een vraagje ik hoop dat je mij kan helpen.
Ik heb deze ook op mijn motor maar ik wil nog alleen de knipperlichten ervan blijven gebruiken.
Kan ik zomaar de kabels verwijderen van de dagrij verlichting/achterlichten? Zoja, welke kleur kabels dan precies. Sorry ben niet zo technisch maar wil het graag zelf doen :p
Hoi. In theorie heb je gelijk, het loskoppelen van de kabels van de achterlichten zou moeten werken. Helaas kan ik je niet helpen met de kleuren van de kabels omdat ik het simpelweg niet meer weet, ik heb deze motorfiets 6 jaar geleden verkocht.
What seat do you have on your bike, is that the original factory seat? It looks different and nicer than the factory Yamaha seat here in the USA. Thanks
It is accessory yamaha OEM Comfort seat, but it only looks nice,
in fact, it is harder and uncomfortable than the factory one, the worst spent 250 euros ever 😉
@@MotoAndy Thanks for the feedback!
Hi, what if instead of soldering the cables I use hermetic connectors for all connections?
Thanks for the reply
you can use connectors if it's more convenient for you, I prefer soldered connections so I did it my way, good luck
Thanks! 😉@@MotoAndy
Hey! Thanks so much for this video - really helpful! Just one quick question.. is there any reason why you don't add the resistors on the blinker-side of the connectors instead of cutting cables in the motorcycle? I'm pretty new to this so would prefer to not cut any cables on the bike.. :-)
You can install resistors on the blinker cables, but if you want to disassemble the blinkers later or the entire tail tiddy, you will not squeeze the resistors through the holes in the housing. cheers, ride safe.
Do u think that this can be done on Aprilia?
Well I found the answer already in a other comment! Thanks for the video!
I have the same lights on a new machine now - i wonder if i can just use the rear brake lights without the position lights ... just brake lights and blinkers.. is that possible if i leave the blue wiring disconnected ?
I think so, but I'm not sure, you just have to try it. Good luck.
@@MotoAndy i will checkt that out the next days and report back
@@MotoAndy Disconnecting the blue wiring worked, i now have the break lights and Blinker lights, the Position lights are off.
Great, thanks for update 👍
Hi Andy (and anyone else)!
Thank you very much for the video.
But is it possible to get a printed installation manual (PDF)?
Google is your best friend 😀 Im sure you can find something there
@@MotoAndy I couldn´t find it :-(
@@PeterP38 I don`t have it any more so I can`t help you. Try yamaha forums maybe somone have it.
Im stuck on these
Tail light working
I can get the stop lights working each side but when I connect the tail lights up the stop lights wont work
Sorted
Your welcom 🤣😉
Question: 7:49 "Position Light" I've never heard this term in brake or signal wiring. What exactly is the 'Position Light' wire for ??????
Pretty sure it's the 'Tail Light' wire ! Thanks.
Position light = tail light
Parking lights. Basically the same as the front
Siema a nie można zamiast tych dwóch opornikow zamontować poprostu nowy przekaźnik pod led?
możesz próbować, ja założyłem i oporniki i przekaźnik, oporniki są dostarczone w zestawie ze światłami
Można. Miałem oporniki, wstawiłem przerywacz do kierunków LED i oporniki wymontowałem. Działa tak jak powinno i trochę mniej śmieci poupychane za plastikami.
Hi, is possible use this LED just for blinkers? Thank you. Great video btw.
i think so, just don't connect the positioning light wires
@@MotoAndy please which store can I get one online?
www.cmsnl.com/products/led-blinker-rear-plus_ymeflb2r10/?locale=nl-nl&gclid=Cj0KCQjwspKUBhCvARIsAB2IYutUfothe2LwEqTOqtOAgRksh_Ort2sptjBacKFMSWfwkdfmzih9MXEaArB2EALw_wcB
www.cmsnl.com/products/led-blinker-front-plus_ymeflb2f10/?locale=nl-nl&gclid=Cj0KCQjwspKUBhCvARIsAB2IYus1SWSRZMZixOR9lyJKiIJUQ3cYRvJ3dReH72Q967GzQmwUK_da_loaAldhEALw_wcB
good video thank you . your not change central signal for install the led ?
I gues you ask about relay, yes I did change relay for LED.
if you installed a LED relay, any reason to still use the resistors ?
emergency lights (hazard lights) do not work with standard relay, resistors are included in the ligts set
What did you change? Did you change to a new relay? If yes, what relay did you put in?
Michael Ingemann I buy Yamaha I relay a 20euro .is impeccable.
How much
Did these pass the MOT ok?
I have no idea what MOT is but they will fit any bike if you have correct adapters
Ok MOT right, sorry still sleepy, I had no problems with MOT in Poland, according to yamaha they are street legal, but every country have different lows, in the Netherlands there is no MOT for bikes, only for cars.
hey can you sell me your original oem clear turn signals. i looked on ebay but no luck. here in usa all the tracer 900 2016 and up only got the orange turn signals from the 2006 yamaha r6
I don't have them anymore
@@MotoAndy oh. do you know where i can get used ones. i cant find 3 wire turn signals for the fronts.
mine was with two cables, with three cables you will definitely not find in europe, try on ebay
@@MotoAndy ah i realized this vid is only for rear install. i'll just buy the oem front and rear from yamaha super tenere and be done with it.
I know what to do now - take the bike to my dealer and let him do it !
I did it the first time too, then I had to correct everything because it didn't work properly, I regret it to this day. Good luck & ride safe
How can I buy this indicators online... Plz put link
Ebay
@@MotoAndy where eBay?
Come on man, use the search browser it cost 1 min to find.
www.cmsnl.com/products/led-blinker-front-plus_ymeflb2f10/?locale=nl&gclid=CjwKCAjw7J6EBhBDEiwA5UUM2rCuD-OJUtSYYNRK9P3ug9abzNAGSciV323anIGayteNUHol03m3RxoCZ2wQAvD_BwE
www.ebay.de/itm/152304669386?hash=item237610d2ca:g:JK8AAOSwMVdYG3UB
Hello,
Can we install thoses blinkers on a motorcycle of different brand? Thank you in advance
Yes of course you can, you just need another housing mount
@@MotoAndy thanks
too complicated, i give up
Dont give up yet.
I just installed a set on a Traceur last night, editing Now....
did you do the front ones too ? - need more information on that job ... Tracer 900 gt 2018
I did. But I'm not one for putting links on others channels.
If you check my channel for the video, you'll find a recent one on it. Same model and year as yours.
Cheers n RSOT >:)