DIY! Honda Fit GE8 Valve Adjustment
ฝัง
- เผยแพร่เมื่อ 25 ก.ย. 2024
- In this video we cover the basics of how to take care of that annoying valve tick that develops on higher mileage Honda Fit engines. This is a lot of work, so this is just a guideline. You should refer to official manuals before attempting to work on your own car.
I'm not sure why this video doesn't have more views and likes thus far, because it's the best one I've seen regarding G8 Fits on TH-cam. Thanks and great job!
280mm Front Rotor is used on the Euro Gen 9 2012 to 2016 Civic 1.4 i-vtec hatch if anyone wanted to keep it all Honda. Fantastic job on the valves one of the best explanations available.
yeah finally some proper and updated fit ge8 vid! keep it up!
I've watched a lot of DIY auto videos in my time, and this is by far one of the best. Clear, concise, well filmed and you did everything properly (and in metric haha) - well done mate, kudos!
I cycle the engine over after adjustment and have had to readjust some. Good video!
Thank you for the great video. I was apprehensive about ensuring that the position was TDC, I used a straight edge to sign the tick marks with the top of the cylinder cover, this made it so much easier.
Great video. Thank you so much. I did this successfully based on your video. Only add would be at the 8:30 mark to use a flat feeler gage on the valve cover edge to line up the cylinder top mark. It was hard to line up the mark visually and I saw this tip (too late) in a different video. I'm pretty sure I got it close, but would have been nice to have been perfect. My '11 Sport has 190K miles and it had never been done but wasn't loud. I did adjust most of them, but didn't get any real improvements in noise, power, or gas mpgs.
Thats what I was thinking, I mean I guess for him the sound was a little better but my 190k '13 sounds like the after and has never had a valve adjustment, ill still probably do it the next time I change the plugs though
What kind of mpg do you average? My AT 11 gets like 32-33 and I drive cautiously
🤦🏽♂️🤦🏽♂️🤦🏽♂️ by watching this I noticed what I did wrong.. thanks for a great video!
It was interesting to see that you were able to fit any feeler gauge in the exhaust valve. Mine were jammed shut when I did this job.
They say the Exhaust values get tighter and the Intake's go looser
Thank you for taking the time to make this video. I have a 2010 Fit and wanted to know what was involved in doing a valve adjustment. Thankfully, the valves sound ok presently, but I appreciate you identifying the fastener sizes and torque specs. It's amazing how many videos are out there that omit such helpful info. Cheers.
Thank you for this video! I’m about to do the valve adjustment on my Crz. Our engines are the same other than the transmission and electric motor.
Really outstanding video. You are a natural !!. Unlike my Honda Accord, doing a valve adjustment on my Homda Fit, was far more involved. Thanks for walking us through each operation, step by step !!.
Perfect way to inform. Will tell peoples about your vids
If you ever got around to the big brake conversion, I'd love to see that too.
This is fantastic, Patrick!
Manuel Carrillo III thank you sir!
Thanks for this, man. It's helping me get ready for the job.
This looks to be a really quick and simple job.
Thanks for the very detailed video. I have a different technique for valve tightening Though. I make all the adjustments with the filler gauge still wedged in the valve, then tighten the nut. My car sounds like a well oiled sewing machine now. Very quiet in fact.
This is a really good DIY video! It was clear and concise! Perfect!
One of the BEST DIY videos I have ever seen! Thank you!
Video ben fatto e lavoro scrupoloso, complimenti.
Very smooth video!
Excellent Video..
Since so much is being removed, what other parts should be replaced? (I was mostly thinking about hoses or other rubber items)
Easy peesy..make sure to get "bent feeler gauges" napa has em.
Great video!
Grease those wheel nuts (do breaks while your down there ) lol. Why dont they ever say how to keep the parts where they can be found and not lost? I would put them in plastic zip lock bags and tape them to the part and number them from first to last items that are taken off as they are in order . And clean the throttle body and replace plugs check everything you can while all that crap is out of your way. Hoses and belts too! Dont forget that valve cover . plug s & throttle body cleaner and your hand cleaner for you! Lol. So does sny one know how much it costs to get it done st a shop?
I had a bunch of maintenance done at 100K for about $1200. That included valve adjustment, spark plugs, coolant change, and a bunch of other routine stuff that would be done more often. I'd bet the valve adjustment was a big chunk of that just based on how much needs to be removed to get there.
just put some copper based grease between the brake disc and the rim
Great vid. Big help for me
Thank you!
Dang that's alot of removal 🥺 but doable
Great work!
Very good job..
I'm not sure where to find service manual for 2015 Fit. I'd love to have one.
i have the exact same engine in my honda jazz (aka fit) do you happen to know where the crankshaft sensor is please? i need to get mine replaced but im struggling to locate where it goes lol and online forums arnt helping !
If you’re a beginner, how do you remember putting all that back together if you’re not recording it?
Yo what did you just say about the break upgrade being cheap I needa see that video
After doing valve adjustment is it ok to drive the car for the day or wait a day for rtv to dry?
Is it recommended to change the timing chain after a valve lash adjustment?
My 2012 Honda Fit Sport has 294,000 miles on it and I'm ashamed to say I've never had the valves adjusted or checked. Recently it's developed a clattering noise that lasts until the engine warms up. Even when the engine is cold it's not really noticeable at idle, but is very noticeable under light throttle. Could this be due to the valves needing adjustment?
It could be a valve adjustment, but also could be that initially the oil isnt reaching all the places it should while the engine is cold but when it warms up it reaches up to the top of the crank case and lubes everything up. I would do the adjustment, and when the valve cover is off look for any sludge or buildup that might be affecting oil while cold. Also before you do your next oil change, run some seafoam high mileage motor treatment through the crankcase for 50-100 miles, this can dissolve some of the sludge and buildup, but make sure you change your oil and dont leave it this way for more than 100 miles or so. I also like to use some motorkote and lucas high mileage oil stabilizer on engines with this many miles, really helps to reduce friction and wear, and if your're hearing noises while your engine is cold youre definitely hearing that wear. add some of that to the crankcase after your next oil change..
I should also say that it could be piston wear as well, the piston can clatter inside of its bore when the engine first starts up, and then as it heats up the piston expands to deacrease the clearance between the engine and the bore. using a bore scope you can look inside each cylinder for damage to the cylinder walls, unfortunately this is one of those things that happens to really high mileage engines, but ive seen engines go for a long time with this problem as well, eventually if the engine is rebuilt it needs to be bored....i would take it really easy on the engine until its warmed up, until you find out what the problem is exactly...
@@MattB90 Thanks for the replies! I’ll try those.
The way you filmed and explained is top of the class teaching material. However, the result compared to the original noise is insignificant to me. Both are noisy.
All Hondas have a valve tick, it’s normal.
Patrick you have a like from me and subscribed but the intake valve is 0.15 mm and the exhaust 0.26 mm, you have to adjust again the valve mate..good video
Thank you for the like and subscribe. Intake acceptable range is 0.15 - 0.19 and exhaust acceptable range is 0.26 - 0.30. Setting them at 0.18 and 0.28 respectively means they are within acceptable range and do not need additional adjustments.
@@patrickmorgan4268 0.15mm for intake and 0.26 mm exhaust when the engine it's cold and 0.19 mm and 0.30 mm when the engine is hot mate,remember this think :) have a nice day!
@@agamitzadandanache2379 You're spot on re: hot/cold, although personally I'd be a /little/ conservative if you don't have total confidence in the precision of your feeler gauges and allowing for a little creep when torquing the jam nuts.
@@agamitzadandanache2379 That's actually wrong. First, you're not supposed to do this job with a hot engine. You're supposed to do this cold ONLY. 90 deg F or below. Second, when the engine is HOT you need LESS clearance because metals expand when hot. That's the entire point of having valve clearances.
@@agamitzadandanache2379 First of all, you can't do this with a hot engine, just because the time it takes to remove the cylinder head cover is enough for the engine to cool itself.
Second, the service manual clearly states “Adjust the valves only when the cylinder head temperature is below 38 ° C (100 ° F).
Temperatures are not differentiated between intake and exhaust.
This is to be clear to everyone.
Mai dandanache, mai, tare ai dat-o tare cu nuca-n perete incercand sa pari destept.
Best way to shift a wheel that is stuck like that is a swift donkey kick to the top of the wheel.
cute engine
good video but still has a tick in the after video. not a bad tick but its still there.
how often or mileage should you make the adjustment
How do you know that mini cooper's rotors will fit into your hubs?
Because they’re both 56.1mm center bore with a 4x100 lug pattern. There’s a set on my car now squeezed by ITR calipers. Stops on a dime.
👍👍👍👍👍👍👍👍👍👍👍👍👍👍
This engine is way too clean inside. You should change it's oil a lot less often, or it's never gonna wear out.
Judging by the outside, this vehicle is in the rust belt. Body will rust out way before any engine issues materialize.
The emblem in the grille is crooked. Is this a Hyundai ?
Oh god... You stuff the intake manifold but go ahead and scrape old gasket sealant right beside the exposed timing chain....!!!
Honda fit, remove the windscreen wipers before changing the engine oil 😜
thank you Mr.Patrick
Is it just me, or are the valves on a Fit noisy no matter what? That's been my experience.
Are they? I just got to digging cause my Toyota after 170 k has no valve noise still then this fit has had a little since we got it with 30k miles.