Penyebab parking brake di volvo fm 400 versi 4.parking brake tidak mau aktif apa pak? Jadi di port 28 dan 29.2 di APM keluar angin terus.kira2 komponen d APM apa yg menyebabkan itu?
Apakah switch parking brake nya menyala saat di parking? Kondisi release 28.1 dan 28.2 itu selalu ada angin, sedangkan 29.2 itu juga selalu ada angin, sedangkan saat parking, angin tidak ada diposisi tersebut
@@chrisnsangarasi9440 alhamdulillah sudah ketemu pak.. Sampek mumet trnyata ada yg lupa dpasang spring yg di PCV dekat protection valve nya.yg bongkar konco jdi gak copy 😁 Awalnya error actuator stuck open pak 😄
Only c107473= actuator stuck closed, wheel 1 rpm pressure control. Rootcause damage piping or part between rpm and wheel brake,damage piping or part between rpm and supply pressure, received supply pressure value from apm incorrect,rpm damage
dan kabel yang saya perbaiki adalah kabel warna biru dan putih yang terdapat pada konektor/solenoid abs yang berada pada bagian belakang sebelah kanan pada output valve.
1. Trailer control module or its pipe connection is damaged or incorrect trailer control port is not plugged 2. Trailer control module supply line is damaged. 3. Spring brake lines are damaged. 4. Parking brake relay valve failure 5. Sensor failure 6. APM internal valve failure
TCM: disconnect the TCM pipe on APM port - close it's port with plug. check park brake application and release 5 times. if it's working failure free, replace TCM.- Exhaust: check Park brake relay valve silencers for blocking and dirt, check the plastic cover (plastic part can be removed for the check and put back after) of the secondary exhausts on the bottom against dirt and blocking.- Relay valve: exchange relay valve if other actions are not effective.
C10022F=Large airgap, dirty tone wheel, missing or destroyed tone wheel teeth, toggling tone wheel, production-failures of tone wheel, damaged wheel speed sensor, wheel speed sensor mounting. Action="Check the tone wheel for dirt and metallic particles, for wobble, for pitch error, for the correct number of teeth.Check wheel speed sensor mounting (Check ""Klämhylsa"").Check the cables and connectors between ECU and wheel-speed sensor for short-circuits and open-circuits.Measure resistance of Sensor and cabling. Resistance must be between 800 ... 2000 Ohm.Measure insulation resistance of sensor and cabling to vehicle GND. Resistance must be > 200kOhm.Do waveform check with oscilloscope. Check and correct air gap between wheel speed sensor and tone wheel by measuring the wheel speed signal. (Wheel speed sensor signal must be higher than 100mV peak to peak at wheel speed of about 3-5km/h). U300049=Too high battery voltage or damage of the vehicle's power supply system or damage in the wiring or connectors for the ECU supply or damage in the wiring or damaged dataset or damaged software or damaged ECU Action= Replace ECU U114286=Signal invalid, Wheel-Based Vehicle Speed
Oh mae. Mai. Kawa jua ulun seorangan nanti perbaiki 😁😁😁
Bisa ai Mun hakun😁😁
@@chrisnsangarasi9440 hahaha ulun pasrahkan ke ahlinya aja guru ku memang award memang guru ku isak ini 💪💪
❤❤❤
Thanks
Mantap
Siap up
Yg sangat ditunggu ²
Ini hanya bagian kecil troublenya, bisa juga karena sensornya
Biarpun masalah kecil kalau tanpa ilmu juga susah om.. makasih terlah berbagi ilmu
Setuju,👍
Itu truck dari PT mana bang, soalnya baru tahu kalo truck Eropa mewah ternyata ada di Indonesia. Setahu saya PT Siba Surya juga memakai truck eropa
Adaro
@@chrisnsangarasi9440 oke siap
Duhhh maen km kurang jauh bro ,
Aq 7 tahun di siba surya jdi mekanik , di tmbng bnyak truck2 eropa
Godd job sir ! and what about the DTC BI *?
B= Body, Please write the error
B15AC00
I guess the webside to see DTC details that you show in your video is open ?
MTCO faulty (Time
difference between display
and chart carrier)
action is needed.
1. Reload MTCO SW
2. Check MTCO
Kapan Ulun d training guru
Pian guru jua,beda spesialis saja,😁🙏
Penyebab parking brake di volvo fm 400 versi 4.parking brake tidak mau aktif apa pak? Jadi di port 28 dan 29.2 di APM keluar angin terus.kira2 komponen d APM apa yg menyebabkan itu?
Apakah switch parking brake nya menyala saat di parking? Kondisi release 28.1 dan 28.2 itu selalu ada angin, sedangkan 29.2 itu juga selalu ada angin, sedangkan saat parking, angin tidak ada diposisi tersebut
@@chrisnsangarasi9440 alhamdulillah sudah ketemu pak.. Sampek mumet trnyata ada yg lupa dpasang spring yg di PCV dekat protection valve nya.yg bongkar konco jdi gak copy 😁
Awalnya error actuator stuck open pak 😄
Wah mantap, ternyata kalian repair sendiri solenoid dalamnya ya,luar biasa👍👍
@@chrisnsangarasi9440 terimakasih pak 🙏
Banyak belajar jg dr channel pak chris dan mas feri 😃
@@kepitinghutan4321 siap,mantap
Code no. C107478 + U114286 trouble error TRUK BRAKE FAILURE..
C107478 no match, U114286 = signal invalid from wheel based vehicle speed
Only c107473= actuator stuck closed, wheel 1 rpm pressure control. Rootcause damage piping or part between rpm and wheel brake,damage piping or part between rpm and supply pressure, received supply pressure value from apm incorrect,rpm damage
@@chrisnsangarasi9440 Thanks for the information bro...
Kapan yg new series datang??
Sudah operasi sebagian, bentuk sama,fitur berbeda
Apa saja Warna dan fungsi kabel pada konektor yang di hubungkan ke EBS pak?
Harus lihat wiring dulu
Pak, bisa saya belajar sama pak soal ABS?
dan kabel yang saya perbaiki adalah kabel warna biru dan putih yang terdapat pada konektor/solenoid abs yang berada pada bagian belakang sebelah kanan pada output valve.
Apakah bisa tolong bapak jelas kan?
Angkutan houling batu bara ya
Betul sekali
Om boleh minta modul error code fh nya om?
Boleh
Bang kalo beli truk di tambang yang tutup itu ngurus suratnya rumit ya bg?
Kalau itu saya gak copy
ممكن ترفع لنا دفتر الاكود الفولفو على شكل pdf
نعم يوجد بصيغة PDF
نريد ان ترفعه وارسله لكي يستفيد الجميع@@chrisnsangarasi9440
هل يمكنك مشاركه البرنامج هذا معنا نريده نستخدمه في الكمبيوتر الخاص بنا
يجب شراء هذا التطبيق من أحد الوكلاء والحصول على ترخيص من شركة فولفو سنويًا عبر الإنترنت
My Volvo 2017 model sem problem ,,,
What's problem?
Truck brake failure
@@chrisnsangarasi9440 what your what's up number
@@niazali7689 chat Only 0812 8286 7521
I found c101d7A
Wait, i m check tommorow
1. Trailer control module or its pipe connection is damaged or incorrect trailer control port is not plugged 2. Trailer control module supply line is damaged. 3. Spring brake lines are damaged. 4. Parking brake relay valve failure 5. Sensor failure 6. APM internal valve failure
TCM: disconnect the TCM pipe on APM port - close it's port with plug. check park brake application and release 5 times. if it's working failure free, replace TCM.- Exhaust: check Park brake relay valve silencers for blocking and dirt, check the plastic cover (plastic part can be removed for the check and put back after) of the secondary exhausts on the bottom against dirt and blocking.- Relay valve: exchange relay valve if other actions are not effective.
Wot the program you use wear take program
Impact program
Ок i ken download internet
@@shamilyubuza5521 nothing on internet
@@chrisnsangarasi9440 wera i kent take ths program
Y me podrías compartir
Ya, 0812 8286 7521
ما أسم البرنامج هذا
برنامج التأثير
Hello brodhır
Hello
@@chrisnsangarasi9440 turçk brake failure ABs mödülü şeması
@@chrisnsangarasi9440 c 001813 vayrinn
@@chrisnsangarasi9440 C 001c13 vayrenkk
@@chrisnsangarasi9440 vatsap number
Modulator ke bang?
What??modulator abs
@@chrisnsangarasi9440 sy ingat punca dia modulator
I found code ABS : C10022F, U300049 and TECU :U114286. Could you help me solve this problem please. Thank you
C10022F=Large airgap, dirty tone wheel, missing or destroyed tone wheel teeth, toggling tone wheel, production-failures of tone wheel, damaged wheel speed sensor, wheel speed sensor mounting.
Action="Check the tone wheel for dirt and metallic particles, for wobble, for pitch error, for the correct number of teeth.Check wheel speed sensor mounting (Check ""Klämhylsa"").Check the cables and connectors between ECU and wheel-speed sensor for short-circuits and open-circuits.Measure resistance of Sensor and cabling. Resistance must be between 800 ... 2000 Ohm.Measure insulation resistance of sensor and cabling to vehicle GND. Resistance must be > 200kOhm.Do waveform check with oscilloscope. Check and correct air gap between wheel speed sensor and tone wheel by measuring the wheel speed signal. (Wheel speed sensor signal must be higher than 100mV peak to peak at wheel speed of about 3-5km/h).
U300049=Too high battery voltage or damage of the vehicle's power supply system or damage in the wiring or connectors for the ECU supply or damage in the wiring or damaged dataset or damaged software or damaged ECU
Action= Replace ECU
U114286=Signal invalid, Wheel-Based Vehicle Speed