I just use the TA-100 to drive my A-300 because the A-300 is worth every dollar but I also have the XPA 2 GEN3 AND THAT AMP IS FANTASTIC IVE NEVER SEEN A AMP RUN SO COOL IN TEMPTURE IN MY LIFE OF 56 YEARS AND SOUND QUALITY IS JUST FANTASTIC AS WELL....I AM A EMOTIVE CUSTOMER FOR LIFE I WAS CONSURNED ABOUT THE POWER SUPPLY IM GONNA GUESS CUZ IM OLD SCHOOL......BOTTOMLINE YOU CANT GO WRONG WITH EMOTIVE......!!!!!!!!!!
Though I get the output i need out of my Emotiva amps using my my Marantz pre-amp but, it leaves me still wondering if i ever could achieve max output form the amp as he does mention 1.7v need to reach max and quoting Marantz from their website "the RCA pre-outs can output up to 1.2V and the XLRs can output up to 2.4V" so based on the 1.2v vs 1.7v a would assume that i would not reach max but, I am not sure.
I have the EXACT same concern. SR5015 sounds great driving my right and left RF-7 IIs and Focal 300 ICLCR 5 center to a crystal clear 80+ dB at my 13 ft listening position; but I'm always stuck wondering if an external amp could sound better. Then I discovered this issue of Marantz's preout voltage. I may never know.
I have the exact same problem with my Onkyo RZ250 Onkyo has released the new RZ 70 however the pre-outs are the same output so I cannot from my understanding get the maximum amount of power out no matter what amplifier I buy unless that amplifier has gain control.
Are Emotiva amps stable into loads less than 4 ohms? The specs seem to always say 4 ohm minimum so that's a bit of a concern for those of us who own Maggies or other hungry speakers.
Crazy - I was doing a search on how to measure pre-out voltage from a receiver and lo and behold this is MY receiver. The Onkyo RZ 730. I have an Outlaw 7000X that requires 1.2V and was considering adding two 2220 but those require 1.6V. Its great to see my receive can supply that voltage (since Onkyo only provides the nominal spec of 1V) should I decide to buy those two 2220 and run the rest of my system (minus the back surrounds) with the 7000X. Also the Onkyo RZ 730 can be configured to display the volume in dB so 84.5 is actually +2.5db and 82 is reference.
Emotiva gear head here TA-100 A-300 CD-100 XPA-2 GEN 3 ERC-3 XSP-1 GEN 2 XPA DR-1 (s) Oh and Airmotiv B1+ (s) Few tee shirts lol Absolutely love Emotiva gear
Lonnie, How about a video where you explain speaker cable sizes? Everyone talks about "watts", but isn't watts=volts*amps? Isn't amps(current) the determining factor in conductor size? How much current is provided by an amplifier to X ohm speaker load at X watts? Another issue is input power supply to the audio rig. Kinda need guidance on 110/220v current supply size there also. Some folks don't know that plugging 30amps of load into a 15amp rated circuit is not a good/safe plan. Oh - all of this math, time for a drink.
I never understood the volume number on most receivers. -40 to 20? Sony was the only one i knew who didn't complicate things. 0-60. How easy is that to know where you are
I have your xpa2v3...love it. Up front I have a freya2. And I recently sold a kidney to get new tekton double impacts. Love the xpa, full, powerful, holographic with the schiit. Bangs. Love it.
Question to Emotiva: I have a Denon DRA-800H Receiver which has Zone 2 Outs. So I presume, I would connect the Denon's Zone 2 Outs to my Emotiva A-300 AMP inputs? Thus amplifying the Zone 2 signals? With this connection, the Zone 2 signal is amplified only, correct? It is not "bridging" the two amps?
Correct, the signal would route through the Zone 2 outputs to the A-300 to your speakers. When connected to the outputs on the Denon, it should mute the internal amplification to those channels.
A question for emotiva. I'm thinking of getting the Onkyo tx-rz50 together with the Base X A3 for the LCR. The specs on the Onkyo tx-rz50 pre-out is 1v.. is that enough to move the base X A3?
I'm wondering the same thing. I have a Pioneer SC-LX904 with pre-out of 1v Thinking about getting the XPA-3 for my LCR. Not sure if that will be sufficient enough for that amp. 🤔
I have that Onkyo and I also have a BASSX-3 I do not feel as getting the full potential as well I asked a guy at Crutchfield about this he was completely stumped he was like you pre-outs will put out enough power I tried to explain to him I measured the power And also see the out put on paper how much,power this receiver puts out....No I'm not getting the amount of full power however I do love their amplifiers.
Hi Emotiva, my system are Yamaha RX 3040 and my speaker are KEF Q950 and center KEF Q600c. I want to add Emotiva XPA 5 gen 3 to my system. If I do can I hear the different on my ht system? I am listening at volume -20 db. Waiting for the feedback. Thanks Emotiva
Yes, with all channels driven you are only getting close to 100 watts of power with your Yamaha. Going with the XPA-5, you will get more than twice that power and really open up your soundstage and system performance. It will be a night and day difference.
![[LIVE] : ONE ลุมพินี 89 | คู่เอก "ยอดไอคิว vs คิริลล์"](http://i.ytimg.com/vi/Z3vYkHJ_5Ig/mqdefault.jpg)
The receiver was an Onkyo for anyone who was curious. Zoomed in on the label @3:27.
My whole system is Emotiva, Preamp, power amp, speakers. Next is CD transporter. Love emotiva
Thank you for your support!
I've had the erc 1, 2, and 3. They are great.
Want to say Thank you for existing and giving us many many hours of happy listening
I wonder how much power is consumed by the XPA gen 3 when just Idling?
I just use the TA-100 to drive my A-300 because the A-300 is worth every dollar but I also have the XPA 2 GEN3 AND THAT AMP IS FANTASTIC IVE NEVER SEEN A AMP RUN SO COOL IN TEMPTURE IN MY LIFE OF 56 YEARS AND SOUND QUALITY IS JUST FANTASTIC AS WELL....I AM A EMOTIVE CUSTOMER
FOR LIFE I WAS CONSURNED ABOUT THE POWER SUPPLY IM GONNA GUESS CUZ IM OLD SCHOOL......BOTTOMLINE YOU CANT GO WRONG WITH EMOTIVE......!!!!!!!!!!
Thank you for your kind words Andrew! Yes our amplifiers run pretty cool compared to a lot of them out there that double as room heaters.
Even my Monster DR1 monoblocks run cool. 650 watts per channel with little to no heat? Amazing!
Though I get the output i need out of my Emotiva amps using my my Marantz pre-amp but, it leaves me still wondering if i ever could achieve max output form the amp as he does mention 1.7v need to reach max and quoting Marantz from their website "the RCA pre-outs can output up to 1.2V and the XLRs can output up to 2.4V" so based on the 1.2v vs 1.7v a would assume that i would not reach max but, I am not sure.
I have the EXACT same concern. SR5015 sounds great driving my right and left RF-7 IIs and Focal 300 ICLCR 5 center to a crystal clear 80+ dB at my 13 ft listening position; but I'm always stuck wondering if an external amp could sound better. Then I discovered this issue of Marantz's preout voltage. I may never know.
I have the exact same problem with my Onkyo RZ250 Onkyo has released the new RZ 70 however the pre-outs are the same output so I cannot from my understanding get the maximum amount of power out no matter what amplifier I buy unless that amplifier has gain control.
Are Emotiva amps stable into loads less than 4 ohms? The specs seem to always say 4 ohm minimum so that's a bit of a concern for those of us who own Maggies or other hungry speakers.
Crazy - I was doing a search on how to measure pre-out voltage from a receiver and lo and behold this is MY receiver. The Onkyo RZ 730. I have an Outlaw 7000X that requires 1.2V and was considering adding two 2220 but those require 1.6V. Its great to see my receive can supply that voltage (since Onkyo only provides the nominal spec of 1V) should I decide to buy those two 2220 and run the rest of my system (minus the back surrounds) with the 7000X. Also the Onkyo RZ 730 can be configured to display the volume in dB so 84.5 is actually +2.5db and 82 is reference.
All I know is my Marantz SR7012 works very well with my Emotiva amps
Emotiva gear head here
TA-100
A-300
CD-100
XPA-2 GEN 3
ERC-3
XSP-1 GEN 2
XPA DR-1 (s)
Oh and Airmotiv B1+ (s)
Few tee shirts lol
Absolutely love Emotiva gear
@@scottyo64 Wow fantastic! Thank you!
Lonnie,
How about a video where you explain speaker cable sizes? Everyone talks about "watts", but isn't watts=volts*amps? Isn't amps(current) the determining factor in conductor size? How much current is provided by an amplifier to X ohm speaker load at X watts? Another issue is input power supply to the audio rig. Kinda need guidance on 110/220v current supply size there also. Some folks don't know that plugging 30amps of load into a 15amp rated circuit is not a good/safe plan. Oh - all of this math, time for a drink.
Thanks for making these helpful videos. More please!!!
Why is the power cord ungrounded?
I never understood the volume number on most receivers. -40 to 20? Sony was the only one i knew who didn't complicate things. 0-60. How easy is that to know where you are
I have your xpa2v3...love it. Up front I have a freya2. And I recently sold a kidney to get new tekton double impacts. Love the xpa, full, powerful, holographic with the schiit. Bangs. Love it.
Keep making those videos.
That's the plan!
Question to Emotiva: I have a Denon DRA-800H Receiver which has Zone 2 Outs. So I presume, I would connect the Denon's Zone 2 Outs to my Emotiva A-300 AMP inputs? Thus amplifying the Zone 2 signals? With this connection, the Zone 2 signal is amplified only, correct? It is not "bridging" the two amps?
Correct, the signal would route through the Zone 2 outputs to the A-300 to your speakers. When connected to the outputs on the Denon, it should mute the internal amplification to those channels.
My onkyo RZ820 leaves 1v as the specifications, what does that mean when you say emotiva needs 1.7v?
How many watts to expect for 4ohms speakers. All channels driven. Martin logan xt60 , xt50 to be exact.
lonnie what think new h-c1 amp
A question for emotiva.
I'm thinking of getting the
Onkyo tx-rz50 together with the Base X A3 for the LCR.
The specs on the Onkyo tx-rz50 pre-out is 1v.. is that enough to move the base X A3?
I'm wondering the same thing. I have a Pioneer SC-LX904 with pre-out of 1v Thinking about getting the XPA-3 for my LCR. Not sure if that will be sufficient enough for that amp. 🤔
I have that Onkyo and I also have a BASSX-3 I do not feel as getting the full potential as well I asked a guy at Crutchfield about this he was completely stumped he was like you pre-outs will put out enough power I tried to explain to him I measured the power And also see the out put on paper how much,power this receiver puts out....No I'm not getting the amount of full power however I do love their amplifiers.
Why emotiva gen1 have less transistors than what they say?
Is this true for the DR3 as well?
Yes!
1.7v input,,, pp.. or rms
Hi Emotiva, my system are Yamaha RX 3040 and my speaker are KEF Q950 and center KEF Q600c.
I want to add Emotiva XPA 5 gen 3 to my system. If I do can I hear the different on my ht system? I am listening at volume -20 db. Waiting for the feedback. Thanks Emotiva
Yes, with all channels driven you are only getting close to 100 watts of power with your Yamaha. Going with the XPA-5, you will get more than twice that power and really open up your soundstage and system performance. It will be a night and day difference.
@@nickmandara8231 Thanks a lot. Already order the Emotiva. 😄
Pound for Pound,Dollar per Dollar,Can't be beat now some silver faced componets Please n Thank You.
Why are amplifiers SOO expensive though? Ughhh, it's not fair.
Now can you tell the wife this cause they don't get this stuff man I get it but we need wife friendly explanations this is an audio file crisis.
Lonnie must be a cyclist or a runner.
Lonnie is the human ant and lifts the heaviest things he can find for fun.
Bye-bye