The information about "Load Config Bundle" towards the start of the video answered my initial question with slic3r, which was, "why doesn't my printer bed size update when I load the gMax slic3r config?" Super helpful, Gordon. Thanks!
Hi, I have a home made 3d printer. I am currently facing issue with z motor position after each layer. My z motors are not moving up as they should and it end-up crashing into previous layer. i am using merlin 2.0 firmware, slic3r for gcodes and pronterface for printing. Kindly advise
I have followed your tutorial with no success! When I click on download I get a different view than what is shown on your tutorial. I get files in a zipped mode and when I unzip them I do not get an "exe" file to complete my download. I am totality lost on what to do next. I have tried over and over again with no success. Can you help me in some way. Thanks Richard
I'm having difficulty accessing gMax forum though I've registered so I will post my question here. I have gMax 1.0, and am using Slic3r and Pronterface. I've set the x and y axis on Slic3r through Pronterface printer setting, and both software showed that the print object is centered, however, when I press print from Pronterface, the extruder goes off the bed. I've also tried printing from SD card and extruder goes off axis and hits the stopper. Is there a way to set axis limits from the printer? There are so many axis abbreviations there. What do I need to do? Please advise. Thx.
Hey, I'm trying to download slicer. When I click on the Windows icon, it directs me to a page that says: "You don't have permission to access /win/ on this server." Could someone please help me get it?
The information about "Load Config Bundle" towards the start of the video answered my initial question with slic3r, which was, "why doesn't my printer bed size update when I load the gMax slic3r config?" Super helpful, Gordon. Thanks!
A tutoral with a high information desity, thanks.
This was exsteamly helpful thank you very much!!
Great video. Thank you for posting!
Hi,
I have a home made 3d printer. I am currently facing issue with z motor position after each layer. My z motors are not moving up as they should and it end-up crashing into previous layer.
i am using merlin 2.0 firmware, slic3r for gcodes and pronterface for printing.
Kindly advise
I have followed your tutorial with no success! When I click on download I get a different view than what is shown on your tutorial. I get files in a zipped mode and when I unzip them I do not get an "exe" file to complete my download. I am totality lost on what to do next. I have tried over and over again with no success. Can you help me in some way.
Thanks
Richard
Richard Harmon same
I'm having difficulty accessing gMax forum though I've registered so I will post my question here. I have gMax 1.0, and am using Slic3r and Pronterface. I've set the x and y axis on Slic3r through Pronterface printer setting, and both software showed that the print object is centered, however, when I press print from Pronterface, the extruder goes off the bed. I've also tried printing from SD card and extruder goes off axis and hits the stopper. Is there a way to set axis limits from the printer? There are so many axis abbreviations there. What do I need to do? Please advise. Thx.
Hey, I'm trying to download slicer. When I click on the Windows icon, it directs me to a page that says: "You don't have permission to access /win/ on this server."
Could someone please help me get it?
do i need to change the bed sizes according to my delta series printer right?
The 1.1.7 config or download section on your website is no longer there
Are there any short college courses in North West England (St Helens) which can instruct in 3D printing?
Hi, I can't install Slic3r on my Window 64bit pc...
Any advice ?
this was extremely helpful thanks
My Slic3r closes when I try load the gMax config. (I tried both).
Can anyone help ?
thankyou verymuch it was very helpfull
a good vid
Time to get a Mac.
Nice tutorial! (y)
windows vista.... '.'