I agree fusing should be done with in 4/8inch of any battery any more u definitely no use for fuse when goes wrong also he said 24 volt but qored in parallel so its still 12 volts
Did this unit come with the metal frame? I want to modify my jeep so i (175#) can ride it with my kid(s) without bending or breaking it. Most of the mods out there are either pretty basic, like a battery upgrade. Or a full build with all steel and gas motor. My plans are in the middle and havemt found a lot
There might be a screw towards the bottom of the shifter. If your vehicle has it, not hard to miss, remove it and put the shifter in the forward most position. That is the high or fast setting. You should have a notable change in speed.
To tie 2 batteries together in series you run the positive of one to the negative of the other. We do this in the harness so as not to cause confusion or alarm when plugging it in.
I have a dune racer and I saw your 18v kit you sell, I read that some trimming on the fins is necasary To make it fit which is no big deal so my question is the 18v kit will fit in the back where the original is and just plug in right??
@@mltoys9644 can i wrap the 12v and 6v batteries together with electrical tape so they dont move around and stay together? is there any harm in doing this?
I purchased the mltoys led light kits
I’m not worried about the car going faster. Planning to wire the batteries in parallel just so the kids can go a little longer before the thing dies.
You mentioned blowing fuses if wired incorrectly/poorly. Where was your fuse installed?
It's not about the location of the fuse holder. That can go anywhere between the batteries and gas pedal.
I agree fusing should be done with in 4/8inch of any battery any more u definitely no use for fuse when goes wrong also he said 24 volt but qored in parallel so its still 12 volts
How are the two batteries balanced in voltage if you're always charging them in series?
I got everything but my question is do i need to change original 12v receiver or motor driver when converting to 24 volt?
Hi I have a question could you show how to bypass or modify a boomerang ??
Did this unit come with the metal frame? I want to modify my jeep so i (175#) can ride it with my kid(s) without bending or breaking it.
Most of the mods out there are either pretty basic, like a battery upgrade. Or a full build with all steel and gas motor. My plans are in the middle and havemt found a lot
So basically your saying the car is slow without the kit? I got my son the same one and it goes really slow. Did anyone else have this issue ?
Slow is relative. Power Wheels rates it at 2.5mph in low speed and 5mph when you take the high speed lockout screw out. (That's slow in our books)
There might be a screw towards the bottom of the shifter. If your vehicle has it, not hard to miss, remove it and put the shifter in the forward most position. That is the high or fast setting. You should have a notable change in speed.
How hard is it to do an AWD conversion? My nephew wants to do AWD powerslides.
It takes customer fabricating skills to pull it off. Rarely done auccesfully.
@@mltoys9644 I figured... I'm gonna try to do some research on it and see if I can't try to make this work.
Where can I get the kit
MLToys.com
Non stop blows fuses
Can you send me a wire diagram for installing your led light kit for a power wheels Ford f150
Please contact support at GoFast@MLToys.com
why is the kit so expensive ? you can buy two brand new racers and still have money left. Not even talking about a marketplace
The autofocus having a seizure
for those not electronically savvy, can you explain why the red/white lead is going into the negative side of the battery on the 6:40 mark?
To tie 2 batteries together in series you run the positive of one to the negative of the other. We do this in the harness so as not to cause confusion or alarm when plugging it in.
The motors and gears dont need upgrading going to 24v???????
They will eventually if not immediately need upgrading. Our Stage IV or V Motor/Gearbox kit is the best way to go.
I have a dune racer and I saw your 18v kit you sell, I read that some trimming on the fins is necasary To make it fit which is no big deal so my question is the 18v kit will fit in the back where the original is and just plug in right??
After I trim the plastic fins in the way right??
Correct
@@mltoys9644 What is the best method for trimming the plastic fins? I too ordered the 18v kit.
@@pigz5022 A dremel tool is easiest. Small hack saw is second choice. Most Dune Racer's don't require any cutting though.
@@mltoys9644 can i wrap the 12v and 6v batteries together with electrical tape so they dont move around and stay together? is there any harm in doing this?