This is the best explanation ever. I was about to throw away my new atmega328P. However after successful burning the bootloader, I am now able to use the IC. Thank you
Your descriptions were excellent. I understand much more than before. Plus I now have "refreshed" and newly burned microcontrollers. You definitely have a new subscriber.
Hi, I'm a beginner. So to put bootloader into a chip, you use sketch called ArduinoISP with 'ArduinoISP' profile. After compiling and succesfully upload the sketch, you switch different profile called 'Arduino As ISP' and burn bootloader. Do I understand it correctly? Now how do I put a sketch to the new chip if I don't want to remove atmega chip from my working arduino?
My Arduino UNO has a surface mount chip and not through hole can i use the same method to burn bootloader on a through hole microcontroller? I want to use the new microcontroller on a breadboard with Arduino codes not to replace the old chip on my Arduino.
I have a problem, I have tried all your step as you mentioned but trying to burn bootloader, is telling me this error message "could not find usbtiny device (0x2341/0x49)
I have this error: Error quemando bootloader avrdude: Yikes! Invalid device signature. Double check connections and try again, or use -F to override this check.
Avrdude dislikes your lovely 328-PU chips and says “avrdude: Yikes! Invalid device signature.” or "avrdude: Expected signature for ATMEGA328P is 1E 95 0F" Soln:- This problem happens becoz ur arduino uses 328p - pu and if u bought 328pu(a couple dollars cheap). The soln is to modify Arduino > hardware >tools>avr>etc and open avrdude.conf file as word document.keep backup of this file incase u mess up. find 1E 95 0F text under Atmega328 and change it to 1E 95 14 and save. restart arduino environment and burn bootloaders on all ur chips.use status leds as mogul said.they help a lot. After burning change the text in avrdude.conf file back to 1E 95 0F and restart arduino ide.Then u can uplode code normally.
For an Arduino, you can set it up to use the internal 8MHz clock. Configure your Arduino to utilize the internal 8MHz clock, and remember to adjust any timing-sensitive parts of your code accordingly, as the clock frequency has changed. If your arduino originally had a 16MHz external crystal, this alteration might impact the timing of your program.
Would like to know, I'm doing a project with Arduino and already programmed him. But I had to change the code so needed to program again. I need to do all this steps again, like load Arduino as ISP to Atmega328?
Yes, if you need to reprogram your Atmega328 chip, you will need to follow the steps to load the Arduino as ISP onto the chip again. This includes connecting the appropriate wires and using the Arduino IDE to upload the ISP sketch. Once the Arduino is set up as an ISP, you can then upload your new code to the Atmega328 chip using the appropriate programmer settings in the IDE.
help me pls this methode not work for me ( avrdude: Yikes! Invalid device signature. Double check connections and try again, or use -F to override this check) i have two new atmega328p
Avrdude dislikes your lovely 328-PU chips and says “avrdude: Yikes! Invalid device signature.” or "avrdude: Expected signature for ATMEGA328P is 1E 95 0F" Soln:- This problem happens becoz ur arduino uses 328p - pu and if u bought 328pu(a couple dollars cheap). The soln is to modify Arduino > hardware >tools>avr>etc and open avrdude.conf file as word document.keep backup of this file incase u mess up. find 1E 95 0F text under Atmega328 and change it to 1E 95 14 and save. restart arduino environment and burn bootloaders on all ur chips.use status leds as mogul said.they help a lot. After burning change the text in avrdude.conf file back to 1E 95 0F and restart arduino ide.Then u can uplode code normally.
Dear sir hi, when I upload the program in arduino uno like a blink led or fade program through android phone, mobile screen show, Error, problem up loading to board. Plz help me explain me how I fix this problem. I also select the arduino uno board in board setting. I tried so many time but same issue plz help me, explain me, if you no mind plz help me thnx.
Sir am design digital DC Volt metre using UNO board, working is fine. But using only ATmega ic + 16MHz crystal, working is not fine LCD reading is very fluctuate. Program is same. Any solution sir ?
Fluctuations in the LCD reading could be due to issues with the power supply or noise affecting the analog components. Ensure a stable power source for the ATmega IC, check the connections, and consider adding decoupling capacitors near the power pins. Additionally, grounding and shielding can help reduce noise. Double-check the wiring and try isolating potential sources of interference.
doesn't work for me... I don't know why this is the error message : avrdude: Expected signature for ATmega328P is 1E 95 0F Double check chip, or use -F to override this check. Erreur lors de la gravure de la séquence d'initialisation. Ce rapport pourrait être plus détaillé avec l'option "Afficher les résultats détaillés de la compilation" activée dans Fichier -> Préférences.
The Arduino IDE displays anavrdude: stk500_recv(): programmer is not responding error message indicating its inability to establish communication with the ATmega328PU chip. To address this issue, you can consider a few potential solutions. First, updating the Arduino IDE software might prove helpful. Additionally, installing the latest drivers for your USB port could resolve the problem. Ensuring that the ATmega328PU chip is in reset mode before attempting to burn the bootloader is essential; this can be achieved by grounding the reset pin on the chip. For Mac users, trying the deactivation of the "USB Debugging" option in the Arduino IDE preferences might be worth considering.
Hi! When I tryed to burn the bootloader to the chip, I recieved the folowwing message: avrdude: Yikes! Invalid device signature. Double check connections and try again, or use -F to override this check. Can anybody help me?
Check Connections: Ensure all connections between the programmer and AVR microcontroller are secure and correct. Clock Settings: Match the clock settings in your programming software with the microcontroller's actual clock frequency. Device Selection: Select the correct microcontroller model in your programming software. If the issue persists, consider trying a different set of hardware components or using the -F flag with AVRDUDE to override the check.Please try these steps and check if they resolve the issue. If you continue to face problems, kindly provide more details about your setup. Alternatively, you can join my WhatsApp, and I will guide you through the troubleshooting process.
why i have this problem.. Arduino: 1.8.12 (Windows 10), Board: "Arduino Uno" avrdude: Yikes! Invalid device signature. Double check connections and try again, or use -F to override this check.
Hey i am having the same issue, kindly help me to solve this i searched a lot to resolve this but cant find any solution for now, please help@ CREATIVE GENIUS
Arduino: 1.8.15 (Windows 10), Board: "Arduino Uno" Error while burning bootloader. avrdude: Yikes! Invalid device signature. Double check connections and try again, or use -F to override this check.
Sorry for the late reply.. So if you're issue is related on (Invalid device signature) so this the common problem. Invalid device signature error indicates that the signature read from the microcontroller does not match what is expected for the selected microcontroller. Make sure Ensure that the clock frequency settings in the Arduino IDE match the clock configuration of your microcontroller. The ATmega328P can be operated at different clock frequencies, and this needs to be correctly set in your code. And select the correct microcontroller model in the Arduino IDE or programming software. For an ATmega328PU, you should select "ATmega328P" as the board. If you've double-checked all of these aspects and are still encountering the error, you might want to try using the -F flag as suggested in the error message to override the device signature check. However, be cautious with this approach as it might lead to programming the microcontroller with incorrect settings.
hello sir can you make standalone programmer for arduino without PC, maybe the arduino using SDcard for save the hex file then just like click the push button and it going flash the atmega8
Creating a standalone programmer for Arduino without a PC is indeed possible. You can use an Arduino board to achieve this, along with an SD card module and a simple user interface, such as buttons and a display. However, implementing this would require a good understanding of Arduino programming, knowledge of the AVR programming protocol, and careful hardware connections to ensure proper functioning.
hello sir....I have this error, can you please help me resolve it .......avrdude: Yikes! Invalid device signature. Double check connections and try again, or use -F to override this check. Failed chip erase: uploading error: exit status 1
Avrdude dislikes your lovely 328-PU chips and says “avrdude: Yikes! Invalid device signature.” or "avrdude: Expected signature for ATMEGA328P is 1E 95 0F" Soln:- This problem happens becoz ur arduino uses 328p - pu and if u bought 328pu(a couple dollars cheap). The soln is to modify Arduino > hardware >tools>avr>etc and open avrdude.conf file as word document.keep backup of this file incase u mess up. find 1E 95 0F text under Atmega328 and change it to 1E 95 14 and save. restart arduino environment and burn bootloaders on all ur chips.use status leds as mogul said.they help a lot. After burning change the text in avrdude.conf file back to 1E 95 0F and restart arduino ide.Then u can uplode code normally.
It looks like you're encountering an error while trying to burn a program onto an ATmega328P microcontroller. The error message 'expected signature for at mega 328p is 1e 95 0f' usually indicates a mismatch between the target microcontroller and the one selected in your programming environment. To resolve this, please double-check the following Ensure, you've selected the correct microcontroller model (ATmega328P) in your programming software. Verify your connections between the programmer and the microcontroller, making sure they are secure and correctly wired. Confirm that you have the appropriate bootloader and firmware for your specific ATmega328P chip version.
Yes, it is possible to upload code to an Atmega8-16PU IC. The process is called "programming" and it typically involves using a programmer device connected to the IC and a computer running software to transfer the code to the IC's memory. The specific process will depend on the programmer and software being used.
This is the best explanation ever.
I was about to throw away my new atmega328P. However after successful burning the bootloader, I am now able to use the IC.
Thank you
perfect, after trying for many days i found this vid and did it in minutes successfully on a new chip i thought was stuffed.
This is literally the best Bootloader ATmega328 chip video to to learn about the ATmega328 chip in the ATmega328 chip world.
Which chip was he using in the video? lol
Thanks very much my men, all the day i was struggling with a usb to ttl, and with your video and arduino uno finally it works.
i try today , i follow your demo. is successful, thanks
Your descriptions were excellent. I understand much more than before. Plus I now have "refreshed" and newly burned microcontrollers. You definitely have a new subscriber.
Clear and to the point, very knowledgeable vdo, thankyou sir.
Hi, I'm a beginner. So to put bootloader into a chip, you use sketch called ArduinoISP with 'ArduinoISP' profile. After compiling and succesfully upload the sketch, you switch different profile called 'Arduino As ISP' and burn bootloader. Do I understand it correctly?
Now how do I put a sketch to the new chip if I don't want to remove atmega chip from my working arduino?
hallo im could say gladly your a genius indeed i have followed every step and everything worked thanks man
the most well explained video on boot loading i have found so far. Thank you
Me too thank you sir
Great Teaching Technique
Very goog dilivery and practicals.thanks
is it possible to chip to atmega 328 as i2c with out Arduino after programming in with Arduino
Very clear and helpful!! Thank you so much !
My Arduino UNO has a surface mount chip and not through hole can i use the same method to burn bootloader on a through hole microcontroller? I want to use the new microcontroller on a breadboard with Arduino codes not to replace the old chip on my Arduino.
Thank you for this posting - it really helped me.
I have a problem, I have tried all your step as you mentioned but trying to burn bootloader, is telling me this error message "could not find usbtiny device (0x2341/0x49)
you are the best bro
I have this error:
Error quemando bootloader
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
Avrdude dislikes your lovely 328-PU chips and says “avrdude: Yikes! Invalid device signature.” or "avrdude: Expected signature for ATMEGA328P is 1E 95 0F"
Soln:- This problem happens becoz ur arduino uses 328p - pu and if u bought 328pu(a couple dollars cheap).
The soln is to modify Arduino > hardware >tools>avr>etc and open avrdude.conf file as word document.keep backup of this file incase u mess up.
find 1E 95 0F text under Atmega328 and change it to 1E 95 14 and save.
restart arduino environment and burn bootloaders on all ur chips.use status leds as mogul said.they help a lot.
After burning change the text in avrdude.conf file back to 1E 95 0F and restart arduino ide.Then u can uplode code normally.
very clear explanation
If the chip has an internal clock is there a method to program without the oscillator and capacitors?
very good video. now we can burn any code directly to the ATmega328 chip by using FTDI cable and make it work.
Wow, you made it easier.... thanks for the video 👏
Does it work with atmega 32u4 too? Can we burn bootloader to a smd type 32u4 with arduino uno like you showed?
No
This helped a lot thanks for the crystal clear content
oh bro I don't know what to say. it took me to understand this. tnx, a lot !!!
Great video! The music was too loud!!! Do your videos without music in the future so they are easier to watch!!!
thanks the explanation, i learned something
Very clear and helpful. You're a life saver :)
Very nice now I want to set it up as 8mhz internal RC
For an Arduino, you can set it up to use the internal 8MHz clock. Configure your Arduino to utilize the internal 8MHz clock, and remember to adjust any timing-sensitive parts of your code accordingly, as the clock frequency has changed. If your arduino originally had a 16MHz external crystal, this alteration might impact the timing of your program.
May I ask, if it is a chip type, bootloader connection is all the same, right?
Yes
thank you Sir for such a nice explanation.
Would like to know, I'm doing a project with Arduino and already programmed him. But I had to change the code so needed to program again. I need to do all this steps again, like load Arduino as ISP to Atmega328?
Yes, if you need to reprogram your Atmega328 chip, you will need to follow the steps to load the Arduino as ISP onto the chip again. This includes connecting the appropriate wires and using the Arduino IDE to upload the ISP sketch. Once the Arduino is set up as an ISP, you can then upload your new code to the Atmega328 chip using the appropriate programmer settings in the IDE.
Can I use 104 instead of capacitor 22?
No, must be a used 22pf capacitor...
@@Circuitoptimize23 ok. thanks~
Very clear and helpful. thanks a lot
help me pls this methode not work for me
( avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check)
i have two new atmega328p
I have the same problem, did you fix it?
Avrdude dislikes your lovely 328-PU chips and says “avrdude: Yikes! Invalid device signature.” or "avrdude: Expected signature for ATMEGA328P is 1E 95 0F"
Soln:- This problem happens becoz ur arduino uses 328p - pu and if u bought 328pu(a couple dollars cheap).
The soln is to modify Arduino > hardware >tools>avr>etc and open avrdude.conf file as word document.keep backup of this file incase u mess up.
find 1E 95 0F text under Atmega328 and change it to 1E 95 14 and save.
restart arduino environment and burn bootloaders on all ur chips.use status leds as mogul said.they help a lot.
After burning change the text in avrdude.conf file back to 1E 95 0F and restart arduino ide.Then u can uplode code normally.
Thanks for saving my exam scorexD
Nos ayudo XD
thank you so much sir very helpful video
Thanks, now I can burn the bootloader to the ATMEGA THREE HUNDRED TWENTY EIGHT CHIP
Would this work with arduino leonardo chip? Atmega32u4?
can this method be applied using arduino nano or arduino pro mini?
Thanks
Arduino nano possible this method, but pro mini not possible...
@@Circuitoptimize23
ok thanks
Thanks a lot. New chip working
Dear sir hi, when I upload the program in arduino uno like a blink led or fade program through android phone, mobile screen show,
Error, problem up loading to board.
Plz help me explain me how I fix this problem.
I also select the arduino uno board in board setting. I tried so many time but same issue plz help me, explain me, if you no mind plz help me thnx.
Sir my recommend please used PC... If you going to burn arduino bootloader I highly recommend pc version arduino ide,
GREAT TEACHER!
Sir am design digital DC Volt metre using UNO board, working is fine. But using only ATmega ic + 16MHz crystal, working is not fine LCD reading is very fluctuate. Program is same. Any solution sir ?
Fluctuations in the LCD reading could be due to issues with the power supply or noise affecting the analog components. Ensure a stable power source for the ATmega IC, check the connections, and consider adding decoupling capacitors near the power pins. Additionally, grounding and shielding can help reduce noise. Double-check the wiring and try isolating potential sources of interference.
doesn't work for me... I don't know why
this is the error message :
avrdude: Expected signature for ATmega328P is 1E 95 0F
Double check chip, or use -F to override this check.
Erreur lors de la gravure de la séquence d'initialisation.
Ce rapport pourrait être plus détaillé avec
l'option "Afficher les résultats détaillés de la compilation"
activée dans Fichier -> Préférences.
Hello! Could you please provide guidance on how to bootload an ATmega328P?
Join my WhatsApp
I understand
Thank u sir
Now how can I program led pixel software in this chip plz help
Pz help
Can I re-burn my old ic?
Yeah It depends on its memory
താങ്ക്യൂ..👌👏
This video helps me a lot.❤️👏
നന്ദി സഹോദരാ
@@Circuitoptimize23 😳😳 WTH..
R you Malayali?🤔
😉.. Yes
@@Circuitoptimize23 poli...engane ingane nannayitt english samsarikkan padichu.source onnu parayamo plzz
Athu oruu valeya storyaa 😁😜
I get this error
avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x1a
What I can do?
The Arduino IDE displays anavrdude: stk500_recv(): programmer is not responding error message indicating its inability to establish communication with the ATmega328PU chip. To address this issue, you can consider a few potential solutions. First, updating the Arduino IDE software might prove helpful. Additionally, installing the latest drivers for your USB port could resolve the problem. Ensuring that the ATmega328PU chip is in reset mode before attempting to burn the bootloader is essential; this can be achieved by grounding the reset pin on the chip. For Mac users, trying the deactivation of the "USB Debugging" option in the Arduino IDE preferences might be worth considering.
Hi!
When I tryed to burn the bootloader to the chip, I recieved the folowwing message:
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
Can anybody help me?
I have the same problem, did you fix it?
@@fenixmunozgarcia2021 yeah, i had contact problema on the breadboard
@@matyasfazekas2481 Oh, thanks, maybe that is also my problem.
How can i fix this? avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
Thank you
Check Connections: Ensure all connections between the programmer and AVR microcontroller are secure and correct.
Clock Settings: Match the clock settings in your programming software with the microcontroller's actual clock frequency.
Device Selection: Select the correct microcontroller model in your programming software.
If the issue persists, consider trying a different set of hardware components or using the -F flag with AVRDUDE to override the check.Please try these steps and check if they resolve the issue. If you continue to face problems, kindly provide more details about your setup. Alternatively, you can join my WhatsApp, and I will guide you through the troubleshooting process.
Pixel dezin ka hex or bin file arduino sa progrem ho sakta hi
sir can we replace atmega328p-pu wit atmega328p-u, please reply
Sure
@@Circuitoptimize23 earned-a-subsriber
short and sweet, thank you :)
Can i use 20mhz crystal??
Sadly no
why i have this problem..
Arduino: 1.8.12 (Windows 10), Board: "Arduino Uno"
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
Same problem bro
Hey i am having the same issue, kindly help me to solve this i searched a lot to resolve this but cant find any solution for now, please help@ CREATIVE GENIUS
@@Circuitoptimize23 i need some help, i am having same issue, error during upload how can i solve this one
Is it possible to do it with ATmega32A?
No....
Arduino: 1.8.15 (Windows 10), Board: "Arduino Uno"
Error while burning bootloader.
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
Same here. Did you solve it?
Sorry for the late reply.. So if you're issue is related on (Invalid device signature) so this the common problem. Invalid device signature error indicates that the signature read from the microcontroller does not match what is expected for the selected microcontroller. Make sure Ensure that the clock frequency settings in the Arduino IDE match the clock configuration of your microcontroller. The ATmega328P can be operated at different clock frequencies, and this needs to be correctly set in your code. And select the correct microcontroller model in the Arduino IDE or programming software. For an ATmega328PU, you should select "ATmega328P" as the board. If you've double-checked all of these aspects and are still encountering the error, you might want to try using the -F flag as suggested in the error message to override the device signature check. However, be cautious with this approach as it might lead to programming the microcontroller with incorrect settings.
Is there any possible way to do this using a phone?😐 Im asking bcz i doesn't have a pc
Must need pc are laptop .. Not possible in phone...
@@Circuitoptimize23 😥
hello sir can you make standalone programmer for arduino without PC, maybe the arduino using SDcard for save the hex file then just like click the push button and it going flash the atmega8
Creating a standalone programmer for Arduino without a PC is indeed possible. You can use an Arduino board to achieve this, along with an SD card module and a simple user interface, such as buttons and a display. However, implementing this would require a good understanding of Arduino programming, knowledge of the AVR programming protocol, and careful hardware connections to ensure proper functioning.
@@Circuitoptimize23 can you make a tutorial for that
May be in future..
Thanks man
It's really working perfectly
Please share synmatic diagram of 5.1 amplifier
hello sir....I have this error, can you please help me resolve it .......avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
Failed chip erase: uploading error: exit status 1
same here.
Avrdude dislikes your lovely 328-PU chips and says “avrdude: Yikes! Invalid device signature.” or "avrdude: Expected signature for ATMEGA328P is 1E 95 0F"
Soln:- This problem happens becoz ur arduino uses 328p - pu and if u bought 328pu(a couple dollars cheap).
The soln is to modify Arduino > hardware >tools>avr>etc and open avrdude.conf file as word document.keep backup of this file incase u mess up.
find 1E 95 0F text under Atmega328 and change it to 1E 95 14 and save.
restart arduino environment and burn bootloaders on all ur chips.use status leds as mogul said.they help a lot.
After burning change the text in avrdude.conf file back to 1E 95 0F and restart arduino ide.Then u can uplode code normally.
Really helpfull thank you
why mine keep saying invalid device signature TT help plsss
Very good ❤👏👏👏👏👏🇧🇷😉👍
I forgot. Was that really an ATMEGAthreehundredtwentyeightmicrocontrollerchip?
Sir how to upload program without removing the UNO board ic ?
Contact me on what's app.. Number provide in the video description...
Merci pour la vidéo
Very very thanks for this. Good explanation
Bunch of thanks to you for your helpful explanation.
Nice
I have an error while burning:expected signature for at mega 328p is 1e 95 0f
Use -f to override error while burning
It looks like you're encountering an error while trying to burn a program onto an ATmega328P microcontroller. The error message 'expected signature for at mega 328p is 1e 95 0f' usually indicates a mismatch between the target microcontroller and the one selected in your programming environment. To resolve this, please double-check the following
Ensure, you've selected the correct microcontroller model (ATmega328P) in your programming software.
Verify your connections between the programmer and the microcontroller, making sure they are secure and correctly wired.
Confirm that you have the appropriate bootloader and firmware for your specific ATmega328P chip version.
@@Circuitoptimize23 the error is corrected thank you ❤❤🥰
Sir can you please tell me why we use 22p F capacitor? can we use different values of capacitor also?? Plz Plz answer
No no you only used 22pf capacitor, for 16mhz oscillator...
Sir, i have a request for you please making video on how to burn bootloader into to atmega328p by using Arduino Nano please.
Thanks for your suggestion... 👍
Hello brother can we upload any code inAmega8-16pu ic.
Yes, it is possible to upload code to an Atmega8-16PU IC. The process is called "programming" and it typically involves using a programmer device connected to the IC and a computer running software to transfer the code to the IC's memory. The specific process will depend on the programmer and software being used.
Thank you brother
THANK YOU VERY MUCH, LOVE YOU MAN LOVE YOU
pls tell me background song name in this video
th-cam.com/video/x_YYrhnGitM/w-d-xo.html
I bought 6 of those chips and I threw them in the bon fire with some gasoline. They are now all burned.
Now you can use them👍
Thanks a lot I really needed this🙏
Thank you!!
thank you so much
thanks 👍👍👍👍❤️
think you
👍
Thank you Sir , problem solved 🫡
👍👍👍👍👍❤👍👍👍👍👍
Pretty awesome!
i have a problem
What's problem. I can helped you
Thanks
thank you
😂😂😂
Background Music Is Loud...
Unable To Listen ...
500 w amplifier
Thanks soooooooo much