Products that we use and recommend: ► Purge Valve (check for your car): amzn.to/3NnLZu0 ► Panel Removal Set: amzn.to/3YiMADu ► Tool Set: amzn.to/3p5MM6t ► Screwdriver Set: amzn.to/3XRB28Q ► Castrol Oil: amzn.to/3xBc8B9 ► Oil Filter: amzn.to/3w0Ulme ► Torque Wrench: amzn.to/32qyRwg ►Liqui Moly Engine Flush: amzn.to/3IiDBID ► OBD Scanner that we use most often: amzn.to/3I4MQfe ► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics
Hello my friend, can this valve make the car open ABS? I was drivine played with bjg lights and suddenly abs popped, car reduced speed and engine light opened. I did a diagnostic and the problem is this valve. I played again with big lights and again the same thing, Abs poped and car slowed speed. What do you think? Can this valve affect abs?
I don’t have any lights indicating that there is any problem but do you think that changing the purge valve could potentially help with the rotten egg smell I’m getting when I rip it also do you think it’s something I should change based on mileage I’m also getting poor gas mileage
He described EXACTLY what is wrong with my vehicle and I've also confirmed this with my best friend who is also a mechanic. At first I thought it was bad gas, my coil pack going out, and my O2 sensors going out. I just changed the valve and cleared the code with my friends code reader and it instantly started running better and idling better. And the light hasn't come back on so I can get it inspected now! Thank you!!
Awesome. I have a 2010 hyundai elantra and it’s doing the same thing, rough idling, and hesitant take off but once I get going it’s not so bad. Throwing the same codes too. I’m gonna go change it today and see if that’s the issue.
You just have to tune your ear to hear it. I work in a high tech industry, lots of people from all over the world, China, India, Africa and Russia, each person, even some Americans, like say from the south, you have to get used to listening to them. I can't imagine how I would sound speaking their language.
You were right on. I as getting P0170, 0038, 00136 and was about to replace the MAF and Downstream O2 sensor and all it was was a pin sized hole in the 6 inch vacuum hose from the Purge Valve to the intake manifold. You saved me hundreds of dollars and hours of time. Fixed it for under $5 and in under an hour of time. BRILLIANT VIDEO.
My car would start and run fine until it got hot and under load, then it would severely hesitate when trying to accelerate. Car was a Hyundai Elantra 2006
Thank you very much, it solved my rough idle issue on my Mazda B3000. I've already spent $440 trying to fix this rough idle. I've been told i needed a new fuel pump, fuel injector cleaning and using expensive premium fuel.
Hi , I have a 2006 corolla verso with bad idling when cold, tried a lot already too. Didn't yours have error codes, mine has not? What was it, was it stuck opened?
My 2001 Jeep TJ throws a P0455. I was proud of myself when I fixed a loose vent hose at the filler neck. The code returned. I replaced the gas cap. The code returned. I found a section of the vent pipe that was rusted through above and behind the driver's side rear shock and repaired that. The code returned. Thanks to your explanation that a purge valve stuck open imitates a vacuum leak that causes hard starting (and mine cranks longer than it should especially in the morning), I now know to check my purge valve. Thanks for the help, brother - you definitely earned my subscription.
Hi guys, thanks for the useful video! Studied what "purge valve" really is. In older cars it was the same system)) - fuel tank ventilation. Just hose on a tank with non return valve on the end of it. Thanks for the new word combinations I studied in English 👍: -Purge valve - клапан продувки (бака); -Engine misfire - пропуски зажигания двигателя ("двигатель троИт"); -Stuck close (open) - заклинил в закрытом (открытом) положении. Good luck!
I like to thank you so much for your video. I own a Toyota corolla 2005 with 267k. I have been having all the problems that you had mention on this video. I had spend hundreds of dollars trying to diagnostic the problem for the past four years. I also had gone to four different mechanics and they could never figure out what seemed to be the problem. I even bought a new computer for the car, thinking it was it. I was to the point of getting ride off and pass to someone else not to deal with. I also been trying to do my homework on watching videos like yours to see if I could find the solution. Until one day I came across your video, I decided to give my last shot. You have saved me from buying a new car and being able to continuing driving a car that I been for the last teen years now.
Hi Claudio, I have a 2006 corolla verso with bad idling when cold, tried a lot already too. Didn't yours have error codes, mine has not? What was it, was it stuck opened?
Just ordered mine for my chrysler 200, I have an EVAP code and engine light so trying this first since there are so many things it could be. He did a great job.
A really great video. Had P0171 Lean mixture code come up for my 2012 Zafira C. Replaced the Purge valve - code cleared and all is currently working well.
Great video, completely overlooked this and didn’t expect it to be able to cause those same issues I have. For the sake of how cheap the part is it is worth a try
Thanks King! 🔥💯 just replaced the maf and then got an 02 sensor code p0403 but everything in my heart been telling me it was the purge but I’m just finding out the name for it today so that I’m able to replace it! 10/18/2023
I actually like his accent, he is very Good At what he does. AND, I UNDERSTAND HIM JUST FINE SOOOOOOO,.......THANK YOU, for helping a remedial (GIRL) Mechanic. BECAUSE I HATE GETTING JACKED AT THE REPAIR SHOP . PLUS HOW WILL YOU EVER KNOW, IF YOU DO NOT LEARN....?
I have the P0441 code, one say was really cold and the light was off,, the next day comes back on. can you let me know what I need to fix. Thank you in advance.
Been having a hissing sound coming from around my pruge valve on my 300c hemi... Never thought to check it out, just got an 441 code tonight so months of investigation may have been saved by watching this... Thanks brother! Awesome video, and even better accent 🙏🏿 Russian/Ukrainian?
So if a purge valve is stuck open, fuel vapor from the charcoal canister continuously flows; so I gather that also then doesn't allow the canister to become properly saturated with tank fuel vapors; so I gather then there will always be more air than calibrated in the ECM for a normal purge. I gather the ECM knows/is calibrated to the fuel/air ratio in a normal demanded purge. SO then the engine performance should be better on a full tank, and get worse as the fuel tank empties and has more air in it. SO if you wanted to test the purge valve idea you could compare the performance on a full tank and half empty tank?? Fuel Trims would improve on a totally full tank and get worse on an empty tank??
So I have no engine lights or codes but I have noticed something odd my gas lasts longer seems to not drain as quick when it above half a tank if it’s below it seems to go quicker. Plus the car sometimes will act up rough idle some staling hard starts once gas drops below half a tank. Could this be the purge valve stuck open again no codes no engine lights but all the symptoms seem to match.
My car stalls at signals. RPM needle is unstable while that happen. But i replaced this valve with my friend’s car and the car ran smooth without any issue whatsoever.
Hey guys thank you for all the videos of repairs on the 2004 330ci. I have one also I have replaced a lot of parts on this car within the past year. I've replaced the idle control valve and it still has a rough idle and bogs when I press the accelerator, and still throwing the codes P1504 and P1508 what am I doing wrong. I've taken everything back off. When I put everything back on tomorrow I'll take a video of it running so you can hear it.
i have very rough idle at cold start..sometimes i may have to crank twice at cold start..stalls and finally clears out..also when i refuel it completely doesn't want to start..changed plugs,fuel pump,coolant temp sensor,injectors..i will give this a try tomorrow..its Toyota a 1AZ-FE btw..
So I have a P0171. I've watched all you videos on it. So I know it is a vacuum leak. Trim raises at idle then lowers when accelerating. Now, when I take off the vacuum hose connecting to the Purge Valve intake, and I place my finger over the opening (basically closing the valve) the trim returns to normal and car runs fine. Does this sound like I have vacuum leak on the hose leading to the gas tank? Notes: purge valve turns on and off just fine when I test it with a battery. It's closed when car first starts, then opens as car warms up.
If it is stucked in open position , your engine's idling rpm will increase considerably due to excess fuel & air and will vary for the initial 15 minutes of drive. If it happens & to confirm simply remove the hose from purge valve engine side while engine is running and block it with finger , the rpm will come down & get stable.😊
What is the relay to the purge valve is not working? Will that be the same as the scenario you described when the purge valve is continuously open? Have a car with a missing fuse to the purge and it has problems starting, sometimes it just cranks and does not start, other times it start but cannot speed up to 130km/hr. Any thoughts on the issues is much appreciated.
Can i delete the 1st converter off my 2010 Nissan altima 2.5 ? And put a straigh pipe to go to the next converter? Emission test are not required in my state of S.C
I replaced the purge valve and after a month of so I'm getting the same lights- fuel cap open and check engine light. Gonna check the hose and if it's alright, I'll just replace the fuel cap.
Not sure if it's the purge valve or not. I drive a standard Chevy s10. It has trouble starting and idling. And it constantly revs at stop lights without me using the gas pedal at all.
Products that we use and recommend:
► Purge Valve (check for your car): amzn.to/3NnLZu0
► Panel Removal Set: amzn.to/3YiMADu
► Tool Set: amzn.to/3p5MM6t
► Screwdriver Set: amzn.to/3XRB28Q
► Castrol Oil: amzn.to/3xBc8B9
► Oil Filter: amzn.to/3w0Ulme
► Torque Wrench: amzn.to/32qyRwg
►Liqui Moly Engine Flush: amzn.to/3IiDBID
► OBD Scanner that we use most often: amzn.to/3I4MQfe
► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics
Hello my friend, can this valve make the car open ABS? I was drivine played with bjg lights and suddenly abs popped, car reduced speed and engine light opened. I did a diagnostic and the problem is this valve. I played again with big lights and again the same thing, Abs poped and car slowed speed. What do you think? Can this valve affect abs?
RICKY BOOBY ! Lmfao
I don’t have any lights indicating that there is any problem but do you think that changing the purge valve could potentially help with the rotten egg smell I’m getting when I rip it also do you think it’s something I should change based on mileage I’m also getting poor gas mileage
He described EXACTLY what is wrong with my vehicle and I've also confirmed this with my best friend who is also a mechanic. At first I thought it was bad gas, my coil pack going out, and my O2 sensors going out. I just changed the valve and cleared the code with my friends code reader and it instantly started running better and idling better. And the light hasn't come back on so I can get it inspected now! Thank you!!
Awesome. I have a 2010 hyundai elantra and it’s doing the same thing, rough idling, and hesitant take off but once I get going it’s not so bad. Throwing the same codes too. I’m gonna go change it today and see if that’s the issue.
Did u have lean bank 1 and 2
To everyone complaining about the accent, move on, I understand him perfectly.
Both of you come from same place?
@@gto861 Yes, Earth.
ok guy 2:20 lag guy
@@gto861 lol lol...well said
All I know is he has solved my problem, if you can’t understand him go to someone else’s video.
This video is amazing. The accent didn't make it hard to understand him at all. He gave alot of good information that other videos didn't provide.
yeah it's a strong accent, but he's still very clear and concise. good on him.
I actually find his accent enjoyable to listen to
You just have to tune your ear to hear it. I work in a high tech industry, lots of people from all over the world, China, India, Africa and Russia, each person, even some Americans, like say from the south, you have to get used to listening to them. I can't imagine how I would sound speaking their language.
You were right on. I as getting P0170, 0038, 00136 and was about to replace the MAF and Downstream O2 sensor and all it was was a pin sized hole in the 6 inch vacuum hose from the Purge Valve to the intake manifold. You saved me hundreds of dollars and hours of time. Fixed it for under $5 and in under an hour of time. BRILLIANT VIDEO.
My car would start and run fine until it got hot and under load, then it would severely hesitate when trying to accelerate. Car was a Hyundai Elantra 2006
Thank you very much, it solved my rough idle issue on my Mazda B3000. I've already spent $440 trying to fix this rough idle. I've been told i needed a new fuel pump, fuel injector cleaning and using expensive premium fuel.
Hi , I have a 2006 corolla verso with bad idling when cold, tried a lot already too. Didn't yours have error codes, mine has not? What was it, was it stuck opened?
My 2001 Jeep TJ throws a P0455. I was proud of myself when I fixed a loose vent hose at the filler neck. The code returned. I replaced the gas cap. The code returned. I found a section of the vent pipe that was rusted through above and behind the driver's side rear shock and repaired that. The code returned. Thanks to your explanation that a purge valve stuck open imitates a vacuum leak that causes hard starting (and mine cranks longer than it should especially in the morning), I now know to check my purge valve. Thanks for the help, brother - you definitely earned my subscription.
Hi guys, thanks for the useful video!
Studied what "purge valve" really is. In older cars it was the same system)) - fuel tank ventilation. Just hose on a tank with non return valve on the end of it.
Thanks for the new word combinations I studied in English 👍:
-Purge valve - клапан продувки (бака);
-Engine misfire - пропуски зажигания двигателя ("двигатель троИт");
-Stuck close (open) - заклинил в закрытом (открытом) положении.
Good luck!
Thank you❤. I feel comfortable now knowing that my mechanic told me the truth
I actually like this guy, very informative. I watched also some other videos but he explained straight to the point. Keep on teaching us👌
The best auto repair video ever. this guy knows his stuff
I like to thank you so much for your video. I own a Toyota corolla 2005 with 267k. I have been having all the problems that you had mention on this video. I had spend hundreds of dollars trying to diagnostic the problem for the past four years. I also had gone to four different mechanics and they could never figure out what seemed to be the problem. I even bought a new computer for the car, thinking it was it. I was to the point of getting ride off and pass to someone else not to deal with. I also been trying to do my homework on watching videos like yours to see if I could find the solution.
Until one day I came across your video, I decided to give my last shot.
You have saved me from buying a new car and being able to continuing driving a car that I been for the last teen years now.
Hi Claudio, I have a 2006 corolla verso with bad idling when cold, tried a lot already too. Didn't yours have error codes, mine has not? What was it, was it stuck opened?
You did a great job of describing the effects of a bad purge valve. Thank you!
Thanks for great explanation of stuck open vs closed. It helped me diagnose whether it was a purge valve issue. THANK YOU!
I’ve been having all these problems I pray to god this solves the problem.
Did it?
Thought my transmission was going out until finally this code came up to replace the part. Thanks for the video.
Was it jerking while you were driving on lower rpm??
Omg I have been reeducated on purge valves. Sir you have save me so much money now. Thanks dude 😎😎😎😎😎😁😁😁😁😁😁💰💰💰💰💰
Just ordered mine for my chrysler 200, I have an EVAP code and engine light so trying this first since there are so many things it could be. He did a great job.
Is more than 1 year I have that problem and didn’t know what to do finally found these video which helps me very much. Thank you for your uploading 🙏
A really great video. Had P0171 Lean mixture code come up for my 2012 Zafira C. Replaced the Purge valve - code cleared and all is currently working well.
I thinking you from Poland right you explain very good I am Mexican Viva Poland
Great video, completely overlooked this and didn’t expect it to be able to cause those same issues I have. For the sake of how cheap the part is it is worth a try
Jees some people don't know when some thing is good! The guys, own time, skill/expertise and experience. Jees Guys!!!
straight to the point, good teacher thank you guy
Thanks King! 🔥💯 just replaced the maf and then got an 02 sensor code p0403 but everything in my heart been telling me it was the purge but I’m just finding out the name for it today so that I’m able to replace it! 10/18/2023
Definitely checking the hose on my 98 civic. Been having rough idle issues, Random misfire codes, rough starting unless I hit the gas.
Thanks for your video on purge valve canister . You explain it in detail so I can follow and understand. Thanks again.frm Maui, Hawaii .
I actually like his accent, he is very Good At what he does. AND, I UNDERSTAND HIM JUST FINE SOOOOOOO,.......THANK YOU, for helping a remedial (GIRL) Mechanic. BECAUSE I HATE GETTING JACKED AT THE REPAIR SHOP . PLUS HOW WILL YOU EVER KNOW, IF YOU DO NOT LEARN....?
This helped me so much I’m getting all these symptoms! Have a new purge solenoid on the way should fix my problem! Thank you guys!
Did it work? Was that the problem?
@@ryanwwil sadly no my timing chain jumped and it threw some false codes ☹️
I have the P0441 code, one say was really cold and the light was off,, the next day comes back on. can you let me know what I need to fix. Thank you in advance.
My issue was @4:40. Thanks for the great upload ‼️‼️
Amazing video I have a Infiniti q50 2017 3.0ddtt and I m having all those symptoms 😢 I m going to check the hose to see wassup thx u for that video 🙏🙏
Thank u that helps my Ford Focus just started to act up having both lean code and fuel tank vacuum code.
Excellent video and great explanations!!!
Very awesome cool video you help me fix my friend his truck from far away
Perfectly explained. Thank you
Video was very very very helpful. You explained exactly what it going on with my car
This is one of
the best explanation
Been having a hissing sound coming from around my pruge valve on my 300c hemi... Never thought to check it out, just got an 441 code tonight so months of investigation may have been saved by watching this... Thanks brother! Awesome video, and even better accent 🙏🏿 Russian/Ukrainian?
100% awesome… You my friend are great at explaining things… Great accent made it even better to listen to… lol
Most informative on the subject matter in all of TH-cam land. No joke!!!
I understand him just fine! Thank-you!
Awesome video and appreciate your teachings on this subject.
Excellent video!
So if a purge valve is stuck open, fuel vapor from the charcoal canister continuously flows; so I gather that also then doesn't allow the canister to become properly saturated with tank fuel vapors; so I gather then there will always be more air than calibrated in the ECM for a normal purge. I gather the ECM knows/is calibrated to the fuel/air ratio in a normal demanded purge. SO then the engine performance should be better on a full tank, and get worse as the fuel tank empties and has more air in it. SO if you wanted to test the purge valve idea you could compare the performance on a full tank and half empty tank?? Fuel Trims would improve on a totally full tank and get worse on an empty tank??
Could explain why first half tank seems to last a little longer.
So I have no engine lights or codes but I have noticed something odd my gas lasts longer seems to not drain as quick when it above half a tank if it’s below it seems to go quicker. Plus the car sometimes will act up rough idle some staling hard starts once gas drops below half a tank. Could this be the purge valve stuck open again no codes no engine lights but all the symptoms seem to match.
You guys have helped me make so much cash and help so many people, bless you 🖤
Great Info On This Little Important Engine Component!!!
Thanks, buddy. That was really great!
Your accent is powerful you own the place and the ear pay attention
Very hopeful, thanks for the savings
Great well explained and knowledgeable video... if you needed actual, helpful info on this system, here ya go... thanks for the explanation
Great job now i know my Machenic is was great and told me truth
My car stalls at signals. RPM needle is unstable while that happen. But i replaced this valve with my friend’s car and the car ran smooth without any issue whatsoever.
I got a 2001 740i just gonna go n try this to see if it changes my symptoms
Excellent description. Thank you (:
Good information keep up the great work brotha.
how would you know it was that in the first place? Those problems could associated with many things?
Thank you for this video. I now have better understanding on this valve.
thank you. I have this problem. Car is shaking in coldstart and my carcoil is making a flappy sound. But im not 100% sure its the carcoil.
Thank you for your teaching . I just learned something from your video
Well explain thanks for the video .. 👍
Thanks guy. I wish I had watched it sooner.
I live in the southern USA and I can hear him perfect
thanks, mad respect for teaching. knowledge is power
Hey guys thank you for all the videos of repairs on the 2004 330ci. I have one also I have replaced a lot of parts on this car within the past year. I've replaced the idle control valve and it still has a rough idle and bogs when I press the accelerator, and still throwing the codes P1504 and P1508 what am I doing wrong. I've taken everything back off. When I put everything back on tomorrow I'll take a video of it running so you can hear it.
37 times....Guys, I couldn't help myself guys. Thank you for the info though!!
Excellent ✨👌thanks mate i’m driving a 2018 Buick encore and I have to replace that device
Thanks for information
i have very rough idle at cold start..sometimes i may have to crank twice at cold start..stalls and finally clears out..also when i refuel it completely doesn't want to start..changed plugs,fuel pump,coolant temp sensor,injectors..i will give this a try tomorrow..its Toyota a 1AZ-FE btw..
Did it fix your issue?
@@benludwig3034 not yet..my mechanic said it's the valve seal..but i changed my throttle body now it starts everytime i put gas
@@kennethbryan3738 thanks I appreciate the reply
Thanks guys!
Thnks for video , good info, can you pls let me know if the purge is ticking, is it normal or what?
That’s great information thanks 😊
Excellent video👍straight to the point. I wish all you tube videos where like this.
Thank you Guys! You Guys are awesome Guys
Your Videos are all very excellant, very informative, I give a thumbs up on all of them. Thank you for your great work . Awesome
So I have a P0171. I've watched all you videos on it. So I know it is a vacuum leak. Trim raises at idle then lowers when accelerating.
Now, when I take off the vacuum hose connecting to the Purge Valve intake, and I place my finger over the opening (basically closing the valve) the trim returns to normal and car runs fine.
Does this sound like I have vacuum leak on the hose leading to the gas tank?
Notes:
purge valve turns on and off just fine when I test it with a battery.
It's closed when car first starts, then opens as car warms up.
hey man did you ever figure this out
@@andrewdeluca2485 it turned out to be the purge valve. I found out by testing it again while still on car, it stuck
Thank you ! Great deal of information, really valuable 👍
My 2002 Lincoln LS 3.0 Has a Purge valve and a Vapor Canister Vent Valve Solenoid Which one is the one you are talking about?
thanks guys this was exactly the info I needed again thank you
Thank you
Thank you, SO VERY MUCH! 🙌
If it is stucked in open position , your engine's idling rpm will increase considerably due to excess fuel & air and will vary for the initial 15 minutes of drive.
If it happens & to confirm simply remove the hose from purge valve engine side while engine is running and block it with finger , the rpm will come down & get stable.😊
To replace the hose, is it a silicone vacuum hose or fuel hose?
Thank you I’ll see what I can do .
Thanks !
What is the relay to the purge valve is not working? Will that be the same as the scenario you described when the purge valve is continuously open? Have a car with a missing fuse to the purge and it has problems starting, sometimes it just cranks and does not start, other times it start but cannot speed up to 130km/hr.
Any thoughts on the issues is much appreciated.
Good info thanku
I liked and subscribed!
Thank you.
Your smart as hell my guy
Thank you so much saved Alot $$
Can i delete the 1st converter off my 2010 Nissan altima 2.5 ? And put a straigh pipe to go to the next converter? Emission test are not required in my state of S.C
Great info as always🤠👍
I want to know if that part would also be around the same are for a 2007 explorer?where would i be able to find that part also?
I replaced the purge valve and after a month of so I'm getting the same lights- fuel cap open and check engine light. Gonna check the hose and if it's alright, I'll just replace the fuel cap.
Very helpful. I am having every open purge valve problem.
I got a p0451 on a Cadillac 2006 sts awd I will check this because I also have a o2 bank 2 sensor 2 code coming up
Thank you!
Not sure if it's the purge valve or not. I drive a standard Chevy s10. It has trouble starting and idling. And it constantly revs at stop lights without me using the gas pedal at all.
Very helpful thanks