I've got a knocking CDA engine, not sure whether it's the pistons or bearing knock as customer says he drove with low oil pressure for a long time. I was planning to remove the front bumper and all, engine with transmission until I bumped into this video. Thanks man, you saved me days of hard labour... Great upload..
i’ve got a 2012 cc cylinder 3 and 4 both misfire i think it’s my ignition pack, but it’s also got a pretty bad oil leak, i know it’s a common problem but i’ve tried everything. new vacuum new seal thingy lol new gasket heads, seeing that you’re familiar w these cars can i get your opinion on it??
Hi, 1st try to use the ignition coil 1st to 3rd 2nd to 4th , if there is no difference you should check the compression test to know the status of the cylinder so that let me know the results.
Me too but I think this car come out with everything attached to the engine not like other cars the you have to remove a few screws. From the flywheel.
man, i have a problem with my 2012 passat cc. it goes off and vibrates, and starts to put out a lot of smoke. I changed the pcv valve but still the same. the error it tells me is cylinder number 4, catalyst system efficiency below threshold, u0415, p0299. do you know what it can be?
I've got a knocking CDA engine, not sure whether it's the pistons or bearing knock as customer says he drove with low oil pressure for a long time. I was planning to remove the front bumper and all, engine with transmission until I bumped into this video. Thanks man, you saved me days of hard labour... Great upload..
Waw !!! What a job? Keep doing!!!
Great job 👍🏼
Very nice explanation for your 1st Europian vehicle!
Congratulations!
It is amazing. I am very surprised and can't stop watching. Keep it up!!
I was skimming through the video, jusy fyi guys you don't need to remove the intake manifold to remove the engine. You just don't have to.
how long did this take you to get the engine out?
1 1/2 day
Great video! How much did you end up paying for the motor?
Where do you disconnect flying wheel from?
That’s the question I have where do you get to take the torque converter from the flywheel
It doesn't have any bolts. It’s like Manual transmission.
Man love you! Can I get version without speed-up?
Good experience for Europian vehicles!
Very nice explanation!
hello i have a question. how a can exchanged 2.0 turbo engen to 2.5 simpe engen with gear box ? and its is posible to do this work
If it’s complete with harness & ECU yes 👍
Question, where do you disconnect the transmission flying wheel from?
When you take the engine out it will come out
together
i’ve got a 2012 cc cylinder 3 and 4 both misfire i think it’s my ignition pack, but it’s also got a pretty bad oil leak, i know it’s a common problem but i’ve tried everything. new vacuum new seal thingy lol new gasket heads, seeing that you’re familiar w these cars can i get your opinion on it??
Hi, 1st try to use the ignition coil 1st to 3rd 2nd to 4th , if there is no difference you should check the compression test to know the status of the cylinder so that let me know the results.
After the test just informed me of the results. Thanks for asking my advice!
I watched this video to find the torque converter bolts.
Me too but I think this car come out with everything attached to the engine not like other cars the you have to remove a few screws. From the flywheel.
@@cessna16rr I have done quite a few since then and I think they only did that for a few years.
@@cessna16rr and I have taken out of the top with the radiator still in the car just maybe remove the intake
Content, content, content!!!
Is the engine of the 2014 model compatible with 2016 model? I have a 1.8L Turbocharged SE.
It’s 2 years different so that it is not that much difference, try & good luck.
did you ever try the swap?
Thanks 🙏
I need to know the location of the oil level sensor of that engine
man, i have a problem with my 2012 passat cc. it goes off and vibrates, and starts to put out a lot of smoke. I changed the pcv valve but still the same. the error it tells me is cylinder number 4, catalyst system efficiency below threshold, u0415, p0299. do you know what it can be?
Search it on the Google the code p0299 it is for Turbo
could be fuel injector 4
I am currently doing the same swap. I have a 2012 WV CC and I would appreciate any advice as to where to find a replacement engine.
Check on ebay
Can CBFA be changed to CCTA? If so, what else would you need to do?
Check out this video th-cam.com/video/hNkOQtcW6NQ/w-d-xo.html&ab_channel=HumbleMechanic
2014 cc tsi 2.0 can I swap the engine for 2014 Passat tsi 1.8
@gameovernextweek 1.8 to 2.0 Harnesses & ECU different, because of that you have to have the complete harness & ECU.
@@EbnC thank you very much for your explanation
When swapping an engine on these does the the fifth vin letter matter when buying an engine?
www.vwvortex.com/threads/are-vin-5-digit-j-k-swappable-for-the-same-engine-ccta.8980017/
thanks for the video 😊
My pleasure 😊