Lychee Slicer 005 - Slicing, simulating, and exporting resin settings & slices to any printer!
ฝัง
- เผยแพร่เมื่อ 29 มิ.ย. 2024
- View the entire series here:
• Lychee Slicer 001 - Al...
Get the gorilla skull files here:
skfb.ly/o88MN
www.thingiverse.com/thing:518...
/ @michaelpavlovich
/ pavmike
gumroad.com/pavlovich
cubebrush.co/pavlovich
3d.cgmasteracademy.com/instruc...
www.artstation.com/artist/mic...
sketchfab.com/pavlovich
0:00 - Intro
0:10 - Split
0:44 - Slice
1:25 - Picture
1:34 - Simulator
2:33 - At scale
3:37 - Printing in parts
4:18 - Print time and resin cost
4:52 - Printers and file formats
5:29 - Anti-aliasing
5:38 - Exporting
6:32 - Export scene to a 3D file
7:25 - Boolean hole and slice preview
8:55 - Export Scene
This helped alot. Thank you!
I was trying to figure out Photon workshop for my mono x, saw your video about lychee and tried both in parallel. Man these videos were a great help, I'll be using lychee from now on !
Thank you for this whole playlist! Very helpful.
Hi Michael, when you went through your slices at 1:00 it looked like you had no holes in that skull, ending up with quite a big inverted cup. You're probably aware (and I haven't watched the prior vids) but from what I understand that creates a fair risk of pulling your print off the plate or at least stretching/delamination as the print progresses. Imagine lifting an inverted glass filled with water - that suction effect that holds it to the table does the same for the print on the film. You can adde a subtle hole behind/below the skull where it won't be so niticeable, and air/resin can flow in and out as the print lifts off the film. Afaik Nfep film helps reduce the pressure/suction problem as well.
Hi Michael, thx for these informations - i learned some additional stuff!
But there is a problem i have with the shown printing time and resin volume needed after slicing my models with Lychee. All is fine - even the result but both, printing time and resin volume, are shown up to 20% less than needed in real. I have an Anycubic Photon Mono X and all the settings are set in best ways. So what´s the problem...??!
THANKS A LOT.
What’s your best advice for hollowing? I try it and always fail, if I don’t hollow perfect prints
this might be a dumb question but do i need a usb? how do i use a new usb and put it into my elego mars? do i need import a software into the usb?
Sure, just format it FAT32, and I believe the USB Drive files can be downloaded from Elegoo www.reddit.com/r/ElegooMars/comments/ehgt6o/can_i_use_my_own_usb_stick/
www.elegoo.com/pages/3d-printing-user-support
@@MichaelPavlovich Ok, awesome. Thank you so much. I use to use chitibox and that one I had to download a whole need firmware. Just want to make sure! Also does lychee work with STL files only or CBT?
@@abrilgonzalez5881 You can drag and drop STL files into Lychee no problem, and/or export files from Lychee as an STL, in either File > Export, or while you're in the Export workflow in Lychee, you can Export 3D as an STL file if you need to (like in this video th-cam.com/video/fHTFeVIf_AU/w-d-xo.html )
Awesome content, Great information as always. Would you mind if I reach out to you via email if I have any questions regarding something specific?? Thank you again!
Great series, thank you master!