@@rcwindowfilms Do you know the reason why sometimes when I install window film there are lots of white spots? i think I'm clean enough to clean the glass
@@arullsticker it may be that you to clean out your filter if your not using one or maybe try using one. Clean filtered water is best. Us an rv filter that will help.
Great video; you make this look easy and appreciate you demystifying the process. One question the Dow 995 is easy enough to find on the web- where can anyone buy directly the 3M protective film; they seem to only make it available via installers? Do you sell direct and if so how do I order through you?
Thank You for sharing your "Brilliant" method of controlling the roll of sticky "Cling Wrap" by routing the backing out of the way as you unroll. Last time I did this same job I pulled the backing off and that was the beginning of the end for that attempt at doing a clean job... That was the worst experience I had in over a year of remodeling this house... I am going to redo it with the 8 mil 05 tinted security film, I had been dreading it until now... Again Thank You..! ONE (poss. dumb) question... I assume this film needs to go on bare, clean glass, and NOT over any film that is currently on the glass from two years ago..? In other words, do I need to remove the film that I installed a couple years back.. Or can this actually be applied over the film that is on the glass now?
Nice install! What’s your go-to reliable glass cleaning method when prepping for film installation? Got any tips for hard water stains and buffing out older windows?
That’s a pretty tricky question. It really depends on the situation. Most times you’re not gonna need an acid to remove hard water stains however, depending on the type of glass, it may differ is there a particular situation that you want me to guide you on?
@@rcwindowfilms I was thinking of standard dual pane patio windows, that may have some stains and micro scratches from years of environmental exposure. Would you recommend putting the film on both outer and inner pane?
@@RafaelSwit When considering the application of a film to your glass, I recommend opting for an interior film installation. Given the level of scratches and damage already present on the exterior glass, an interior film is likely to be more durable and longer lasting. This choice takes into account both the environmental impact and the current condition of the existing glass. Choosing an interior film is a strategic decision for enhancing the glass's longevity and maintaining its quality, as the exterior glass unit that exists currently will require more deep cleaning because of the surface scratches and damage present.
Hello, I would like to ask what tool or machine you use to cut the film? Preferably a filmhandler? Or is there a film cutter/plotter that is useful? Thank you
It’s on part 2 Dow Corning 995 Attachment for Security Film on Sliding Glass Door: A Step-by-Step Install (Part 2) th-cam.com/video/TMnmMs9oSwY/w-d-xo.html
Where do you get your commercial tints from? And how do you know what shades to use like one of your other videos had a broken window so you tinted one window and the others were done.
@@rcwindowfilms step by step guide how to tint large windows. It was uploaded 5 months ago but I just watched it yesterday and I believe you used a 78 inch roll so I was curious where to buy that big of a roll and also how to check shades or know what tint to use if pre exist windows are already tinted.
@cbroner9983 We installed the tint originally, so we're aware of the film type and shade. If you're unsure, use a tint meter to determine the VLT. Matching film often needs details from the prior installation or a meter reading. Regarding roll size, it's 72 inches, which is the maximum size most manufacturers offer. For larger sizes, you might need to buy a master roll.
Yes, it’s absolutely necessary that you pre-cut security film to the exact size needed. This insures better overall protection, and better overall rigidity of the film. Essentially it reduces the failure or the chance of failure due to lack of adhesion.
Would you recommend a 5" or 8" fusion stretch handle for installing 8 mil security film? I can see youre using a 5 with a red refil, however an 8 would mean youre able to get more done. However i reckon with the 5 youre able to be sure to get more water out with each stroke as less surface area? Any advice would help! Thanks!
@rcwindowfilms I also have another question, what refil would you recommend for security film (8 mil) I see you're using a red refil but I am more familiar with the bluemax.
@@TheArcesz the red for eight mil and up. The more water you’re able to get out on one pass the faster you’re film will cure , and the less spots of water will remain. Single pass squeegeeing with a red squeegee preferably square face will give you the most consistent results.
@rcwindowfilms Hey man I'd also like to ask what you're opinion is on the "big mouth" squeegees for security film. It looks like you're using 1/4" blades (based off the squeegee you have) I work with people that swear by them however I think they're a bit overkill for 8 mil film, seeing as I'm a young guy and can get all the water out with just a regular 1/4 bluemax in my fusion in one pass. Is it something you use in any other application in your business?
yes, access is still possible. The whole idea is to gain time. Delay entry, doing dual film (film on both sides) is an option, but cost becomes an issue.
You’re a pro…made it look easy!
Respect for the professionalism and skill employed. Great job! Wish you were nearby! 🙂
thankyou for the new learning , i just start my own business for window tinting in bali and i learn verry much from you!!
heck, yeah! Congrats, let me know if you need anything. Like a video request.
@@rcwindowfilms Do you know the reason why sometimes when I install window film there are lots of white spots? i think I'm clean enough to clean the glass
@@arullsticker it may be that you to clean out your filter if your not using one or maybe try using one. Clean filtered water is best. Us an rv filter that will help.
Can this be installed to the inside and outdoor of the door ?
Love it, you measure windows and large objects exactly like I do, using your knee to extend the measure 🤣
Great video; you make this look easy and appreciate you demystifying the process. One question the Dow 995 is easy enough to find on the web- where can anyone buy directly the 3M protective film; they seem to only make it available via installers? Do you sell direct and if so how do I order through you?
Yes, you most definitely can order through us. Most manufacturers offer the film to dealers only.
Great details
Thanks, hey if you have any questions or have anything to add, please let me know. I'm always happy to hear other perspectives
Damn… So Cal…. Wish you were in Chi
Thank you!
Thank You for sharing your "Brilliant" method of controlling the roll of sticky "Cling Wrap" by routing the backing out of the way as you unroll. Last time I did this same job I pulled the backing off and that was the beginning of the end for that attempt at doing a clean job... That was the worst experience I had in over a year of remodeling this house... I am going to redo it with the 8 mil 05 tinted security film, I had been dreading it until now... Again Thank You..!
ONE (poss. dumb) question... I assume this film needs to go on bare, clean glass, and NOT over any film that is currently on the glass from two years ago..?
In other words, do I need to remove the film that I installed a couple years back.. Or can this actually be applied over the film that is on the glass now?
手勢好好.大師父!
Sure wish you were in the Seattle area so we could use your company for our windows.
For commercial or residential?
@@rcwindowfilms residential
Do you have a link for the slip n stick
Is there window tint that does not have a mirror appearance from outside?
Where can I buy that film?
Great video what wimdow film are you using?
Thanks bud we use a wide variety of films. For this installation we did a eight mil Solar Gard 20 silver
@@rcwindowfilms Thank ypu!
can you please send a link to this 6-inch squeegee?
Thank you. I appreciate it. I have a great electric pump set up. With a water pump if you interested. No need for a compressor anymore. Fyi.
I’m interested email me
Nice install! What’s your go-to reliable glass cleaning method when prepping for film installation? Got any tips for hard water stains and buffing out older windows?
That’s a pretty tricky question. It really depends on the situation. Most times you’re not gonna need an acid to remove hard water stains however, depending on the type of glass, it may differ is there a particular situation that you want me to guide you on?
@@rcwindowfilms I was thinking of standard dual pane patio windows, that may have some stains and micro scratches from years of environmental exposure. Would you recommend putting the film on both outer and inner pane?
@@RafaelSwit When considering the application of a film to your glass, I recommend opting for an interior film installation. Given the level of scratches and damage already present on the exterior glass, an interior film is likely to be more durable and longer lasting. This choice takes into account both the environmental impact and the current condition of the existing glass. Choosing an interior film is a strategic decision for enhancing the glass's longevity and maintaining its quality, as the exterior glass unit that exists currently will require more deep cleaning because of the surface scratches and damage present.
It is briliant bottle, where did you get this my friend? Also that tissue holder is so hard to get here
Can you provide a link as to where to purchase the red 6 inch application squeegee and handle ? 👍🏼
amzn.to/3uSHOkn Pouch
amzn.to/4bPCC1f Toolbelt
amzn.to/3IcbUT4 Tool-bag
amzn.to/3UVFkfy Basic Squeegee for installation
So what does it cost to install for that door? How much should i expect to pay someone out of pocket?
Where did u buy a towel handle? I’ve been in Lowe’s and Homed Depot and they don’t have it
honestly it's just a bungie cord.
Liner I got has a heavy plastic and lighter film. Does the lighter film go in the window.
I suggest inspecting where the adhesive is and make sure to apply the film with adhesive to the glass surface.
@@rcwindowfilms thank you
Hello, I would like to ask what tool or machine you use to cut the film? Preferably a filmhandler? Or is there a film cutter/plotter that is useful? Thank you
It’s called a film handler. And honestly, I would only do a 72 inch the 60 inches of waste of money.
You didn't do the sealing along the edges that you talked about... how do you get that done on something like a door or home window?
It’s on part 2 Dow Corning 995 Attachment for Security Film on Sliding Glass Door: A Step-by-Step Install (Part 2)
th-cam.com/video/TMnmMs9oSwY/w-d-xo.html
Is that soapy water or regular water
Soapy water solution
What's the belt called for all the tools? Or can you provide a link? Thanks
amzn.to/3uSHOkn Pouch
amzn.to/4bPCC1f Toolbelt
Thank you
Where do you get your commercial tints from? And how do you know what shades to use like one of your other videos had a broken window so you tinted one window and the others were done.
which video are you talking about?
@@rcwindowfilms step by step guide how to tint large windows. It was uploaded 5 months ago but I just watched it yesterday and I believe you used a 78 inch roll so I was curious where to buy that big of a roll and also how to check shades or know what tint to use if pre exist windows are already tinted.
@cbroner9983 We installed the tint originally, so we're aware of the film type and shade. If you're unsure, use a tint meter to determine the VLT. Matching film often needs details from the prior installation or a meter reading. Regarding roll size, it's 72 inches, which is the maximum size most manufacturers offer. For larger sizes, you might need to buy a master roll.
You always cut the security film exactly the size you want before install?
Yes, it’s absolutely necessary that you pre-cut security film to the exact size needed. This insures better overall protection, and better overall rigidity of the film. Essentially it reduces the failure or the chance of failure due to lack of adhesion.
what slip solution do you use?
Under soap or slip and stick
What film would u recomend for a standard window
it really depends on the use case. what are you trying to accomplish?
@@rcwindowfilms added security to my windows
Where can we buy the thicker type squeegee?
amzn.to/3TdslVn
How do I make a pre-cut? Can I, like the other tints, prepare a little more, and then cut the excess on the window?
A film-handler is the best way to reduce your cutting and pre-cut to close size.
What is the replacement for 995
@@surfacedesignz3626 SCS2000
@@rcwindowfilms is that what you were showing on the short video to replace caulk ?
@@rcwindowfilms what product did you use on the short video
@@surfacedesignz3626 8mil silver
It was something in replacement for caulk
Would you recommend a 5" or 8" fusion stretch handle for installing 8 mil security film? I can see youre using a 5 with a red refil, however an 8 would mean youre able to get more done. However i reckon with the 5 youre able to be sure to get more water out with each stroke as less surface area? Any advice would help! Thanks!
5 inch all the way, sorry for the late reply. For us we use the 5 inch all the time.
@@rcwindowfilms Thank you man, much aopreciated!
@rcwindowfilms I also have another question, what refil would you recommend for security film (8 mil) I see you're using a red refil but I am more familiar with the bluemax.
@@TheArcesz the red for eight mil and up. The more water you’re able to get out on one pass the faster you’re film will cure , and the less spots of water will remain. Single pass squeegeeing with a red squeegee preferably square face will give you the most consistent results.
@rcwindowfilms Hey man I'd also like to ask what you're opinion is on the "big mouth" squeegees for security film. It looks like you're using 1/4" blades (based off the squeegee you have) I work with people that swear by them however I think they're a bit overkill for 8 mil film, seeing as I'm a young guy and can get all the water out with just a regular 1/4 bluemax in my fusion in one pass.
Is it something you use in any other application in your business?
Applying films both sides make the window much harder to break, compared to one side only ? Can the burglar still kick in & gain entry ?
yes, access is still possible. The whole idea is to gain time. Delay entry, doing dual film (film on both sides) is an option, but cost becomes an issue.