@@user-ih5zr2hx8i It's true, you can't buy time, but conversely if you have limited money and not the ability to earn high wages, then this short expenditure of time may cost less than a new set of shears.
There is a very handy tool called a Dremel. Even has a rounded emery wheel and polishing paste in the kit. Nice job, but that is a lot of work when a $40 tool that will also do a multitude of other tasks can do it much quicker.
Or if you have a real shop with tools, a reciprocating spindle sander. They spend 1 minute of a 6 minute video cobbling together a sander that isn't as stable and doesn't work as well.
@@mikeroth5518 I'm in the Nursery business, 25 years. I keep cleaning my secateurs when not busy. I use sandpaper, cleans off sticky residue and sharpens.
Folks, just disassemble secateurs, sharpen 5 min on an oil stone/water stone, reassemble, good to go. [Use a bit of fine steel wool and some WD-40, if you need to clean off some gunk]
Might depend on how far gone they are. Removing the gross notches uses up a lot of the oil stones surface. Good stones are expensive but sand paper is a few cents.
Another civilization, Russia, but my wife and I have the same problem. I even agree that it is my responsibility to put them in order, but for this it is necessary that she does not lose them somewhere in the garden. And then there are these little rakes and garden trowels.
The problem with letting mimes make TH-cam videos is they can't explain the details, like: Do you try to maintain the original bevel? What is that clear liquid - water? What grit emery paper? Is that superglue?
Dear Karen, not everyone in this world speaks english. This video was pretty straight forward and if you still have questions after watching this, you probably shouldn't play with your husband's powertools anyway. Please stay safe and get a helmet
Paper was 240 grit wet or dry., spritzed with water. Yes, it obviously was superglue. The rubber was an old bike inner tube….in a pinch you could probably use a stronger painters tape. I watched it one time and from a lifetime of working with and maintaining hand tools I picked up on the answers to your questions.
Nice video on sharpening the tool. To avoid rust, you should also apply some grease on the blades after cleaning the blades before storing them. After several grease sessions, the blades will inherit a thin film of grease on them which protects it from corrosion. If a person takes good care of a tool, the tool will work perfectly for him or her.
how is any of this a "special way"? All you did was clean the blades, grind, polish, and sharpen them. This is basically the standard way to sharpen any blade
"Sharp as a razor" is wrong. The edge isn't durable enough to hold up. You're not trimming your beard; you're trimming wood of variable hardness. Go look at a factory edge on one in the store and make it no sharper than that.
You can by honing and grinding wheels for very little money. But this is OK if you have a lot of time to kill every day. Actually, if you buy a Dremel, you won't even have to take it apart.
There are many ways to accomplish this task. This is just one, and certainly not the best one. It's not necessary to polish the tool unless you want to display it on the wall. This tool is designed for rough use. Someone will jam it into the dirt to cut roots off, it will be thrown in a drawer to rust again. However you do want it sharp and to operate properly. Oil the joints, and use a stone or even a file to make it sharp. Clean it with a wire brush. This ain't rocket science.
And to keep them sharp, I have a bottle of silicon oil but any oil will do. I soak a rag with it in a bowl and wipe them down after every use. Still going after 10 years.
Very good demonstration of how to do it, although you forgot to ad a film of oil to them before you put them back together, that helps prevent rust in between the two sides ,the nut and bolt can also be done, a dab of superglue on the end of the bolt after the nut is screwed down will prevent the nut from self loosening, which can sometimes be an issue,
Give non toxic furniture paste wax a try instead of oil that will run off. Works as a lube in the pivot joint also. Carpenters use paste wax on tools and bare metal table tops to keep them slick and rust free. Oil can contaminate plants. The best rust prevention is cleaning and drying secateurs after each use. The nut you see on this secateurs is a locking nut. It has a plastic insert that prevents loosening.
A Dremel tool will also work to do this but Dremel does not offer a extra large sanding drum.The much larger diameter of the drill chuck works better, and not everyone can afford a Dremel.
So after going through all the trouble of making the "drill attachment", you still used to stone to sharpen the edge. What a waste of time and energy. None of these so called "hacks" really work.
If you'd taken the time to notice...the abrasive paper was 250g the stone is probably 1000g the dowel with compound is the finishing polish...the hack works pretty well.
Hello respected content creator, I am very interested in the content you have created, and if you are willing, I would like to request permission to re-upload it on our platform. We are ready to share the revenue with you. Thank you.
Ужас. ......ужас..... столько затрат..времени, трудов, средств. А новые ножницы стоят 5. - евро. По истине, если собаке делать нечего......
Thanks bro
Decent ones cost around €20. Better to maintain them than throw them away
Смотря как относишься к потраченному времени относительно конкретно данной цели , восстановить ножницы. Время не вернёшь, не купишь...
Vccbmĺķķ8
@@user-ih5zr2hx8i It's true, you can't buy time, but conversely if you have limited money and not the ability to earn high wages, then this short expenditure of time may cost less than a new set of shears.
There is a very handy tool called a Dremel. Even has a rounded emery wheel and polishing paste in the kit. Nice job, but that is a lot of work when a $40 tool that will also do a multitude of other tasks can do it much quicker.
ok man
That's one sharp bikini trimmer!
Or if you have a real shop with tools, a reciprocating spindle sander. They spend 1 minute of a 6 minute video cobbling together a sander that isn't as stable and doesn't work as well.
@@mikeroth5518 I'm in the Nursery business, 25 years. I keep cleaning my secateurs when not busy. I use sandpaper, cleans off sticky residue and sharpens.
What if you don't have $40 to spare? This is long-winded but worked with what the guy had to hand.
Make sure you clean your wife's toothbrush and put it back exactly as you found it.
Lol
No problem here. She's using yours in place of toilet paper.
LMAO.
That's a long winded way to sharpen a blade
I grabbed some toothpaste and the wife's toothbrush and this worked great!
have you heard from her lawyer yet?
Thanks bro
And then you wife tried to kill you bro?
It’s sad the world has lost its sense of humour……☹️
And she grabbed yours and gave up toilet paper. Win-Win.
great but what is the point if you dont give us a list of what you used !
Folks, just disassemble secateurs, sharpen 5 min on an oil stone/water stone, reassemble, good to go.
[Use a bit of fine steel wool and some WD-40, if you need to clean off some gunk]
Do you actually need a list? It's perfectly self-explanantory.
You don't know what he's using? Best you don't try this.
Skip the first steps and sharpen with an oilstone.
Yeah, this was a pretty ridiculous, long way of doing something that can be done better and faster the old-fashioned way.
Might depend on how far gone they are. Removing the gross notches uses up a lot of the oil stones surface. Good stones are expensive but sand paper is a few cents.
What part of her body did you do it on?
Considering that they are meant to prune small bushes and thin branches, I wouldn’t expect them to be able to cut rubber tubing. 🤷🏼♀️
Sharpen things using the Rube Goldberg method.
Ok man
Excellent. My problem is with my wife. She uses them,never cleans or lubricate and let them sit somewhere under the rain😢
Thank you for supporting the channel
Another civilization, Russia, but my wife and I have the same problem. I even agree that it is my responsibility to put them in order, but for this it is necessary that she does not lose them somewhere in the garden.
And then there are these little rakes and garden trowels.
Are we married to the same woman?
Change your wife...
What a way to find out I'm in a polygamous relationship.
Loved the McGiver throttle lock!
Thanks bro
4 out 5 dentists approved of this video.
You only need the oilstone not all the other theatre. 🙄
The problem with letting mimes make TH-cam videos is they can't explain the details, like: Do you try to maintain the original bevel? What is that clear liquid - water? What grit emery paper? Is that superglue?
Ok man
Dear Karen, not everyone in this world speaks english.
This video was pretty straight forward and if you still have questions after watching this, you probably shouldn't play with your husband's powertools anyway.
Please stay safe and get a helmet
Paper was 240 grit wet or dry., spritzed with water. Yes, it obviously was superglue. The rubber was an old bike inner tube….in a pinch you could probably use a stronger painters tape. I watched it one time and from a lifetime of working with and maintaining hand tools I picked up on the answers to your questions.
@@besthubiever This comment wins!
@@besthubiever you’re a tool for being rude.
Thank you. Excellent instruction.
What is the green compound on the piece of dowel in the drill?
Nice video on sharpening the tool. To avoid rust, you should also apply some grease on the blades after cleaning the blades before storing them. After several grease sessions, the blades will inherit a thin film of grease on them which protects it from corrosion. If a person takes good care of a tool, the tool will work perfectly for him or her.
Thanks bro
Ballistol
Fluid Film. THE BEST. does no harm to plants.
What’s TH-cams fascination with using toothpaste for everything except brushing your teeth?
It is effective in cleaning
how is any of this a "special way"? All you did was clean the blades, grind, polish, and sharpen them. This is basically the standard way to sharpen any blade
Thank you for your feedback
@@tipsintelligent2605 you don't have an answer, do you
It's like something you'd do in lockdown due to boredom.
There isn't ONE of these "sharp as a razor" hints that work, NOT ONE!
I imagine that the trick with the dowel and compound makes a very sharp edge.
Gonna try this
"Sharp as a razor" is wrong. The edge isn't durable enough to hold up. You're not trimming your beard; you're trimming wood of variable hardness. Go look at a factory edge on one in the store and make it no sharper than that.
Your ideas are very creative and useful, I like the way you put your heart into it.
Great video. Keep up the good work. Have A Productive Weekend! 🪓🪚
Not very intelligent to use a grinding device spinning toward you. I just use a fine file to sharpen.
I like the little wedge to hold your drill trigger in. Nice ideas.
Ok man
You often find the blades are bent at the bolt hole and have to be straightened.
Red stuff is very mildly abrasive toothpaste. I *think* the green stuff is polishing compound.
Ok man
The low speed means better control. Overal, if you don't have a dedicated sharpening system, this is pretty good.
Thanks bro
Could have done the whole job with the stone in the first place
Ingenious!
Too much trouble to sharpen some shears. I can think of a dozen ways to do it easier.
Please, tell us at least one way.
Terima kasih telah berbagi ilmunya sukses selalu kawan 👍
Thank you for supporting the channel
recommended by 4 out of 5 gardeners to stop blade decay.
Kk
Worth doing this
maintenance if the shears are old and good quality steel.
Very clever!
I went to harbor freight and bought a new one for $2.35. The video was still playing when I got back! DUH!
Thanks man
I don’t plan on shaving with mine, just regular pruning so I will continue to use my metal cloth for all of my edges…✌️
Thank you, it's very easy
You can by honing and grinding wheels for very little money. But this is OK if you have a lot of time to kill every day. Actually, if you buy a Dremel, you won't even have to take it apart.
There are many ways to accomplish this task. This is just one, and certainly not the best one. It's not necessary to polish the tool unless you want to display it on the wall. This tool is designed for rough use. Someone will jam it into the dirt to cut roots off, it will be thrown in a drawer to rust again. However you do want it sharp and to operate properly. Oil the joints, and use a stone or even a file to make it sharp. Clean it with a wire brush. This ain't rocket science.
Ok man
Just cleaning out the mating surfaces can do wonders.
The toothpaste part was GAF!
what kind of paste?
Yea I really have old bicycle tubes lying about, all that messing around when you can use a simple knife sharpener I use it on all my garden tools
no, it should be done from one side only
Well done, sir.
Thank you.
Ok mam
Excellent...!!
And to keep them sharp, I have a bottle of silicon oil but any oil will do. I soak a rag with it in a bowl and wipe them down after every use. Still going after 10 years.
ok man
What is that green material used? which looks like solid soap
I use a stainless steel polish
all that trouble for pruning shears? Just buy a new one....
Ok man
Do they have Dollar Tree in the 3rd world?
that's like the 40 years in the wilderness to paradise ! Mill file is all you need ! ... be careful you don't lose a finger !!
Thanks bro
Be sure to brush after every prune.
Very good demonstration of how to do it, although you forgot to ad a film of oil to them before you put them back together, that helps prevent rust in between the two sides ,the nut and bolt can also be done, a dab of superglue on the end of the bolt after the nut is screwed down will prevent the nut from self loosening, which can sometimes be an issue,
Thank you for suggesting me, I overlooked this
Perhaps Loktite instead of cyanoacrylate (CN)...
Give non toxic furniture paste wax a try instead of oil that will run off. Works as a lube in the pivot joint also. Carpenters use paste wax on tools and bare metal table tops to keep them slick and rust free. Oil can contaminate plants. The best rust prevention is cleaning and drying secateurs after each use.
The nut you see on this secateurs is a locking nut. It has a plastic insert that prevents loosening.
Look at the video.
That nut has an insert that will keep it locked on, no need to add anything.
Where are u from?
What is the green stuff rubbed on the wood?
It is a polishing compound bar, used on buffing wheels and leather strops for polishing metal.
👍👍👍👍
Hey. That's my toothbrush!
? OFGS just soak those blades in coke overnight. Also, clamping power drills in vises is good for them @_@ Good grief, Charlie Brown.
Thanks bro
Thanks. People chill.
Ok man
Cool idea
Thanks man
Wow.....very clever
I asked
Where are you from?
Use a Drexel tool.😊
Please what is a Drexel tool?
Dremel
what kind of spray?
I use water
Dremel tool with accessory kit is a lot quicker!
Moral of the story: take your shears to your dentist, they have all the tools to sharpen it!
But the dentist will reprimand you for not flossing your shears after brushing..
Useless. Just get a file. Easy ad. All that u show is rigmarole
£2.99 lidl
Congratulations
I will remember that trick.
Ahora que empieza la primavera pondré en práctica este video
ok man
What's the green stuff?
Polishing compound
Green Rouge Buffing Compound
typical guy..use a gallon of clean water to rinse off a soapy trimmer blade...I'm pretty sure he doen't cook or clean house either..
Thanks lady
typical girl to bring it to our attention, nag nag nag ......
No. I bet he built the house instead. While she sat on instagram.
Ever heard of a Dremel Tool ????
Ok man
Should NEVER sharpen the back side!! It must stay flat!
Plus no cavities!
very nice, new subscriber
Thanks bro
Some InoratiBUseL
Ever hear of a dremel tool?
Thanks dude
A Dremel tool will also work to do this but Dremel does not offer a extra large sanding drum.The much larger diameter of the drill chuck works better, and not everyone can afford a Dremel.
All of to sharpen garden shears!?! I think not. Many other easier and quicker ways......
Ok man
Or use a Dremel tool!
👍👍from Norway 🇳🇴
Thanks bro
Chromium oxide perhaps
But the majority of Americans don't know how to use a common screw driver ! 😅
Those persons should buy new and donate the old ones to a handyman
Thank you for supporting the channel
6:15 How wonderful! I learned a lot of tips from your creative videos
Thanks bro
Green stuff?
I use stainless steel wax
The green stuff is chromium oxide polishing compound, available at any hardware store.
Hallo Leute . Die Idee gibt"s schon seit Anno Dazumal ! Ma. sagt im
Allgemeinen Schraubzwinge zu dem Werkzeug ! 🧐 👆
Makasın enzayıf yeri uc kısmıdır uckısmıynan kesmeye kakışıp insanları yanıltmayın
I just use a round file simple
I’d just buy a new one
Why do you want to cut rubber instead of the plants? 😱😱
Toothpaste? I stopped watching there.
Ok man
Toothpaste is a good abrasive.
To not oil the blade and tool upon completion exposes that He is merely a novice.
Soooooryyyy
Great job and I have 3 pairs of these that need the same treatment so thanks for the education~!! Liked and Subbed.
Thanks bro
I think the only information of value here is how to make your own sanding wheel
That is a great trick and I’ll guarantee you one that I will use many times
Thanks dude
So after going through all the trouble of making the "drill attachment", you still used to stone to sharpen the edge. What a waste of time and energy. None of these so called "hacks" really work.
If you'd taken the time to notice...the abrasive paper was 250g the stone is probably 1000g the dowel with compound is the finishing polish...the hack works pretty well.
Hello respected content creator,
I am very interested in the content you have created, and if you are willing, I would like to request permission to re-upload it on our platform. We are ready to share the revenue with you.
Thank you.
Sorry
Pointless theatrics followed by a whet stone. Just use the stone
Its like new 😊
What is the red goo u used to clean the blades with?,also what is he green stuff u put onto the dowel?????
Well can u answer my questions? 🙄🙄🙄
Thank you for asking, I use toothpaste and stainless steel wax
Buy a sharpener for $7!! What a waste of time!
How to not sharpen secateurs.
I'd rather buy a new pair!
Thanks bro