A common problem with new HVAC systems these days.
ฝัง
- เผยแพร่เมื่อ 11 มิ.ย. 2024
- Quality is not what it use to be and probably never will be again. #hvac #airconditioning #cooling #airconditioner #hvaclife #heatpump #hvactechnician #hvacservice #acservicing #hvacrepair
This is what infuriates the consumer to no end!! No quality, no accountability, excessive cost and technology that amounts to crap!!
I hear you! But this is what they give us these days.
Good find !!
If I didn't find that leak, I would need to get a job at Walmart as a self check out cashier.
This video Charles proves that what I have been saying has been corect all along especially with American companies and the coils but part of the problem why these new evap coils in tranes Lennox carrier keep blowing leaks in them is because they are not designed to handle the higher pressures of 410a especially with aluminum.
And I see now with the 410a phase out and so called replacement refrigerents the same crap happening with ohh you will lose some capicity use this refrigerent crap.
But I did see that trane is testing with a company on Comercial rooftop units r 466a right now trying to compete with blueon r 458a.
But here is what I think Charles speaking of old way r458a is approved for r22 systems and blueons patent will expire soon as it's been almost 15 years.
Why not try adapting blueon to work with 410a Systems an option with just changing the pressure switches as necessary and adding adjustable txv valves.
But still have the so called r 452b or whatever other stuff in case of a system leak and just needing to charge up the system temporarily after repairing a leak.
Because this will keep happening until they find a, way to get the pressures back down to what r 22 levels were.
And hint Charles American companies spent all this time adapting their equipment to 410a but now they need to adapt thier equipment to run and be manufactured like the r 22 systems were pressure wise and better and these coil issues with condenser coils and evap coils will stop and with sensers and all that stuff bevause reduced pressures and colder more efficient air equals less stress on the system and we can do with out a2l. Refrigerents or pure r 32 stiff which I don't like at all.
Just my thoughts Charles.
American companies get it together stop with the overcomplicated exclusive proprietary thermostat Comunicating crap and focos on the bigger issues at hand which is getting pressures down. Great video Charles
Great comment
@@unitedtradesmanacademy1894 @unitedtradesmanacademy1894 thanks
lots of computers and technology creates units that are unreliable, difficult to work on and VERY expensive to repair
Bad weld. Nice to have a good company and warranty on anything new. Good find. Hard not to hear that one. Would of been flat soon.
These coil leaks are problems with all manufactures these days, aluminum coils just do not hold up.
@@myHVAClifecheap Chinese junk
I seen the tam and thought "of coarse" 😆
I wish they have some kind of glue to patch that leak rather than replacing. i know it has high pressure.
Question, I see all the Trane Units like this with Silicone on them, what is the Silicone for?
What happened to quality
GONE IN 60 SECONDS.
@@myHVAClifejust like the nation..it went to hell
You da man!
My shitty Goodman coil also sprung a leak only after a year of being installed.... It was right in the middle of the coil..... We were able to epoxy it shut until the replacement coil came in ....
Goodman are all using Chinese parts now. Coils, compressors, etc
isolate the noise and look for the oil saturation on the joints. jeeze thats a lot of silicone they put on there
Inspectors here will fail the inspection if they feel air leaking.
What is all that silicone mess to the right? That looks like some install crap. Lucky for customer the coil is available. Either bad factory braz e or aluminum expansion at the weakest point.
The inspectors will fail inspection if they feel air leaking from anywhere. The sticker says it is designed to leak some air, but the inspectors say it is efficiency loss. We fill the gaps for inspection purposes, but the first time we come back it is gone for good.
Coil is leaking but what about the equalized pressures at the beginning
Compressor spinning backwards from the short cycling
Trane down!!
Our friend says Trane is the best money can buy. I guess we need to start paying with diamonds, oil, or Nvidia chips 😂.
Trane is the less of all the evils, but still a pain. We average, the last 6 years, $5.5M a year in system replacement sales and see a lot larger volume of units than smaller companies. My opinions and experience with Trane come from a larger pool of experience with the product.
Junk overpriced and over complicated 😊all manufacturers 😊
Pretty much American companies need to get it together take cues from companies like Mitsubishi that offer side discharge condensers with inverter technology with exclusive propritiery thermostats that you have to use just for more efficient inverter technologies considered a trane and Lennox but that and the cost turned me right off. Unfortunately.
Or gree with the flex shockingly whether you like Chinese or not thier condenser and evap coils still use copper and are not microchannel with inverter technology and theirs Samsung too and Mitsubishi has the blue ant corrosive stuff that they spray on thier coils.
Just saying you can learn from what other countries do but do it better.