Thanx 4 explaining how its done...you explain how to do it very well...you said once the inlet pipe has to be,smaller...others don't explain in detail as you do...i wish you success..Larry..............Australia ........
If the outlet is below water it doesn't matter. The problem with too big outlet otherwise is that air will come in if the flow doesn't fill the pipe. If air enters the system it will accumulate at the highest point, and will eventually make it stop. It's smart to have a system to trap and potentially bleed of any air.
@@AldriFerdig ... please read my comment and if you want a pumping a water 💦💦 to height level.... put the one-way valve in your out late pipe.... please try this 🙏💐
Hệ thống hoạt động tốt chủ yếu nhờ áp suất nước, nếu để một đầu ống vào, trước tiên nước vào ống tới max, sau khi mở ống xả, áp sẽ đẩy Nước ra mạnh nhưng áp sẽ giảm nhanh và khi hết áp nước sẽ không chảy ra nữa. Nguyên tắc giữ được áp thì nước sẽ chảy liên tục
Thank you for sharing your brilliant ideas while I am in the process of buying an electric pump. Since I listened to your video I am now considering to follow your technique to free me from electric bills!🤩
Slmt sa idea..ang pgkakamali nyo lang mas malaki ang tubo ng papalabas kaysa papasok.normal mauubos tlga yan.dapat same size lng ng pipe.pra 24 hrs gagana ang pump tapos d mauubos karga...
No need for the drum. Only pipes and priming water would work. This setup would not work if the elevation of the output is higher than the elevation of the source water
@@glazerhits6080 You are wrong. What you are talking about is the Siphon pump which they already have in their archive videos. This is a free energy drum pump, a better form of a RAM PUMP.
I'll suggest first try for yourself with a small prototype and go for bigger projects. I tried many a time but it doesn't work well. Yes it works for few minutes but eventually the flow of water either begins to flow in droples or the water in the barrel gets exhausted. And that's the reality of it...when tried. I tried a multiple times but the result was the same
please put food coloring on the water you initially put so we can visually see the transition from the water from inside the drum to the new water from the river, thanks and great idea it will help a lot of farmers...
Именно в таких условиях этих бочек не надо. Вы тянете воду на 1-2м на высоту с 2-3метров после спад на ту же высоту и дальше ниже уровня речки. Вам просто нужно обратный клапан на шланге в воде , кран на высоте для наполнения воды полного шланга и на выходе-все вода самотеком потечет. А эти бочки нужны там где воду нужно поднять на уровень выше чем уровень базы воды, скажем для душа без матора если это возможно
Two areas of doubt, firstly about the intake pipe is there a nonreturn valve attached, secondly, the improved version with the extra plastic cylinder is to keep the vacuum pressure constant, thanks for your return feedback?
Its NRV... that hold back the water against gravity in the intake column. And the whole principle is make storage tank vacuum tight. The drum volume also act as storage buffer to maintain the constant flow.. When you open the outlet valve, water rushes in due to level deference though the drum outlet. And this creates vacuum in the entire supply chain connected to inlet water column. The vacuum then sucks the water thru water column NRV from river or bore well ( as the inlet). Thus maintaining the flow. Pl note, outlet flow pipe dia must be smaller then inlet pipe.
If you add an inner tube from a bicycle to the air tank and inflate it it will increase the water pressure outflow as the air in the tube acts like a spring and helps push the water out with greater force
Sorry Dan, you are way out. There is no need for those tanks. You could as well use a larger main barrel. In any case, the output must be lower than the source.
Thanks once again for having your update on free water system installation and your team and partner, hope I can do it with my self using your techniques, I have a question regarding on your check valve Sir, I mean is that one package when you buy it at the hardware or is it you combine two items to make that check valve. Because I went to the hardware but I can't find the item you used in the system. Please reply and thank you, more power..
I think pressure guage won't work, the system is working like a siphone, so it has no pressure but it has a vaccume effect, vaccume gauge will do the work.
I watch the first video presentation. I catched and understand the principle immediately. My brother is a water driller and build and construct a lot of pump. Thanks for sharing this. I can iliminate my water pump and electric motor.
Hi I love your vdo and look so natural man I don’t know how to express my feedback but you are awesome for this vdo may be you could make more EP such as additional some gravity support that could make your design give more productive
i watched the other clip ....the explanation is that one need to fill the water all through the system no matter what, opening valves needed at the beginning and at the end of the system as well as in the middle. the concept is negative pressure occurs while you open the valve on land. negative pressure will draw water from the pond to fill up the tank.
The water level in the river must be higher than the outlet to the field. The rest is details. In fact you do not need any drums at all, just a hose or a tube.
@@dettyouy223 The air that manages to enter through the outlet pipe, trying to go to the main vacuum tank will enter the vertical pipes pushing the water in there hence forcing the water down.
The only way for this to work is if the out line is very large. The drop will make a vacuum pulling on the drop line or in line it should equalise and stop running. But is worth experimenting with. If you do please make a video so we can see your results. I use the air lift method. It uses atomized water and air to lift. It's lighter than water alone. It will float and bubble into a cistern.
outlet pipe from the drum should be minimum 2.5 times water inlet diameter and then reduced again at the end of the outlet run to increase pressure if needed
@@dano5562 Nah. You've been fooled. The outlet is actually lower than river water level. All you you need is the initial suction to get the flow going. A bit like you would do with a hose that goes up and then down.
@@accaciagame1706 that is not correct... look again. Think of a boat motor drawing gas, from tank, if the tank has no bleed valve the tank will draw a vacuum. that pipe from the river is the filling pipe(aka vacuum fill inlet), the higher we have to lift the water from river more vacuum!!! untill you can even sqaush the drum, this works upto 30 ft!!! if drum is strong enough and holds enough water.
Me too am thinking on the siphone effect in that the outlet is lower than the inlet position. Because siphon works only if the outlet is in a lower than the inlet water level.another point i want to understand is in many similar videos, i observed that tge barrel should be full of water with out any air. If there is air i think it should not work. So i need these two explanations
You have to think the engineering side of the system. The drum is acting as the pump. It does not matter if there is air or not as long as it is sealed after being filled with water. The outlet pipe need not be lower than the water level in the river. Once the outlet stopcock is opened water will flow out, creating negative pressure in the drum. This will in turn suck up the water in the river into the drum and out thru the outlet pipe.
see this youtube video : FREE ENERGY Water Pump FULLY EXPLAINED!! REAL OR FAKE? Eternally flowing water - The truth about eternal flowing water without a pump
Sir I am from india. Big fan of you. Plis surely answer my question. I m going to test it. My question is volume of outlet water is bigger than inlet, so at certain time the tank will be emptied, what will happen than. Wil this work continuesly until and unless there is no leakage and we deliberately stop it???
Thank you for leveling up the free energy water pump...may I request the list of materials needed in the installation of the pump especially the inlet pipe... I can hardly understand that part.
So here he has a drum. Then he has a three valve setup hooked up to the drum. One valve is on the bottom and there are two valves up top. Bottom valve has a pipe after it with a tee and a pipe coming out the top of the tee with a cap on the end of that pipe. The other open end of the tee has another length of pipe and a valve on the end. The First top valve is for air venting, it is located at the back. In the front, closest to source water is a 45 degree bend attached to an elbow coming off the valve. At the 45 degree bend, a pipe is installed to reach the source, this is the inlet. An appropriate filter may need to be installed, as debris would accumulate inside the drum over time. In this particular configuration it can be used without a filter and free flow is used to flush the drum continuously. The water is from a stream that is not very muddy at all. This system is expected to run without clogging for a number of years, until repairing the leaks and possibly changing the drum is required for preventative maintenance. Use ptfe thread tape and ball valve replacements if required. Joiners can be used to repair sections of pipe.
The videos are always informative. Nice to see talent passed down to the youth. Can I use this with a 13mtr well? What's the best height for the drum installation?
DEAR FRIEND! THIS SISTEM Works to Atmosferic Pressure (1,33kgf /cm2 to sea water level). We have loses in the sistem ...THESE loses are praticam limits in 8 meters of water column.TANK you !
If your drum has air in it, then your pickup line is leaking. There should be no change in the water level in the drum. The water level should remain constant and the pump will run forever.
It is just a modified siphon. A siphon uses gravity with an outlet than the inlet. It is not a free energy machine. It is not a pump either, though an innovative way of transferring water.
Well done, but i think there is no need for the drum, but only pipes would do the work. Since the elevation of water as source is higher than the elevation of the output, it would work. But if the output elevation is higher than the source, it would not work without using a pump
Le bidon sert à augmenter la pression dans le système. Je pense que la distance importe peu mais de préférence plus proche du tonneau que de la sortie pour augmenter la pousser
@@alassanebassiti3630 Est-ce que vous avez une idée du principe qui augmente la pression de sortie ? Je comprends que ça capte les petites bulles d'air mais ça n'explique pas à mon sens l'augmentation de la pression de sortie. Si la pression d'air augmente dans le bidon, ça va provoquer l'échappée de cet air en trop !
Just to be clear. This is not a pump, it is a siphon. The drum it to prime the system (fill it with water). The pressure at the outlet (if closed) is the difference in height between inlet and outlet. And of course the outlet must be lower than the inlet. If you could fill it with water a pipe along the ground will work just as well.
@@compostsfertilizers5471 There is nothing insulting here. But if you consider it a pump, where does the energy to pump water come from? If the answer is gravity, and there are no moving parts, it's a siphon.
@@AldriFerdig It's a vacuum system. Water is sucked from the river due to the vacuum created in the drum. the force of the water in the outlet stops air from sipping back hence water from the river raises to the drum.
@@compostsfertilizers5471 Apart from the detail that it's more correct to say that it's the air pressure that pushes the water into the drum, and further until it runs downhill, your description is correct. This is how a siphon works. Btw. there are no vacuum in the drum. A siphon can be used to lift water about 10 meters high, as long as the outlet is lower than the inlet. The limitation is that one atmosphere of pressure equals 10 meters of water. If it could pump water to a level higher than the input it would not be a siphon, but this system is a siphon. A hundred drums between the inlet and the outlet doesn't change this. There are gravity powered water pumps, but this isn't an example of one of those.
@@AldriFerdig May dear these guys a pulling water more than 20feet under ground. And this is now practiced in many countries in Asia, Africa and Latin America. So please stop this unnecessary arguments.
@@LearnForideas Sorry, wrong information. Diameter and lengh of input and output is not critical But, input must be higher than the output. It is a siphon.
Hello, thank you for sharing this kind of project. I am writing to you from Azerbaijan, please answer. What is the approximate length of the outlet pipe? 
For this siphon to work the water level in the river must be higher than the output to the field. With a foot valve at the input, no blue barrel is needed. No need to lift the barrel that high, only makes it more difficult to fill. No need for marer valve just at the output from the drum. No need for white container. No need for the vertical pipe. In short, one simple tube can do this. All the rest is just to get the tube filled with water.
It is a siphon. As long as the outlet is lower than the inlet the middle part can be up to about 10 meters, as that is the water column corresponding to one atmosphere pressure. There are no absolute max lengths, but friction will eventually make it stop depending on the size of your tubing.
I feel so impressed to Link up with people of great minds. my question is that what if I put several air bags along the bigger outlet pipe,will it increase the discharge pressure and also the standing long pipe,is it enclosed or opened because if it's closed, I think this necessitates putting a valve at the drum outlet because pressure in enclosed fluids is equally transmitted through the fluids. this means that without valve at outlet of drum, some water might be forced to go back into the drum once. thanks
فكرة رائعة ومفيدة جدا وطاقة نظيفه لمن لا يمتلك اي مصدر للطاقة .. اجمل تحيه من السعودية
Thank you for this good idea, im a farmer from the Philippines and i will try this technique in may vegetable farm here.
Thanx 4 explaining how its done...you explain how to do it very well...you said once the inlet pipe has to be,smaller...others don't explain in detail as you do...i wish you success..Larry..............Australia ........
Glad to help
If the outlet is below water it doesn't matter. The problem with too big outlet otherwise is that air will come in if the flow doesn't fill the pipe.
If air enters the system it will accumulate at the highest point, and will eventually make it stop. It's smart to have a system to trap and potentially bleed of any air.
@@AldriFerdig ... please read my comment and if you want a pumping a water 💦💦 to height level.... put the one-way valve in your out late pipe.... please try this 🙏💐
It's a brilliant idea, I'll do this in the Philippines, thank you for sharing watching from Toronto
Hệ thống hoạt động tốt chủ yếu nhờ áp suất nước, nếu để một đầu ống vào, trước tiên nước vào ống tới max, sau khi mở ống xả, áp sẽ đẩy Nước ra mạnh nhưng áp sẽ giảm nhanh và khi hết áp nước sẽ không chảy ra nữa. Nguyên tắc giữ được áp thì nước sẽ chảy liên tục
Thank you for sharing your brilliant ideas while I am in the process of buying an electric pump. Since I listened to your video I am now considering to follow your technique to free me from electric bills!🤩
Glad to help
Slmt sa idea..ang pgkakamali nyo lang mas malaki ang tubo ng papalabas kaysa papasok.normal mauubos tlga yan.dapat same size lng ng pipe.pra 24 hrs gagana ang pump tapos d mauubos karga...
Thanks for sharing your genius performance. I promise you that this will revolutionize the world. Keep bringing more of these drum pumps.
Wow, thank you!
Can you install or put or add a Vacuum Pressure Gauge at the top of the drum and focus on it the camera?
No need for the drum. Only pipes and priming water would work. This setup would not work if the elevation of the output is higher than the elevation of the source water
@@glazerhits6080 You are wrong. What you are talking about is the Siphon pump which they already have in their archive videos. This is a free energy drum pump, a better form of a RAM PUMP.
@@LearnForideas a 0 00 0 be
Thank you very much for sharing this innovation. Less cost, more money back to farmers.
So nice of you
Thank you so much for sharing this helpful video. It can be used for fish ponds and also to the rice field... God bless you always sir
Saya ucapkan terima kasi kawan atas edukasinya sangat bermamfaat semoga sukses terus my from Sulawesi tenggara Indonesia
The vacuum can hold back the out going water as well. The pressure equalises
This vid is convincing too. This shows that it's not syphon cause river is very low. Thanks for this.
Great work bro love your work will try this system God bless your work and your efforts
Best of luck
I'll suggest first try for yourself with a small prototype and go for bigger projects. I tried many a time but it doesn't work well. Yes it works for few minutes but eventually the flow of water either begins to flow in droples or the water in the barrel gets exhausted. And that's the reality of it...when tried. I tried a multiple times but the result was the same
Thanks for sharing your knowledge about free water energy installation very nice brother 👍 👌 🙏
So nice of you
Thanks for sharing your great simple technology but very helpfully….👍🏻👍🏻👍🏻
happy to hear that
Thank for sharing this very informative video. this is a big help for our million's of farmer around the world.
please put food coloring on the water you initially put so we can visually see the transition from the water from inside the drum to the new water from the river, thanks and great idea it will help a lot of farmers...
Great idea हम आपके आभारी है
Thank you for sharing this idea and for all your efforts.
Именно в таких условиях этих бочек не надо. Вы тянете воду на 1-2м на высоту с 2-3метров после спад на ту же высоту и дальше ниже уровня речки. Вам просто нужно обратный клапан на шланге в воде , кран на высоте для наполнения воды полного шланга и на выходе-все вода самотеком потечет. А эти бочки нужны там где воду нужно поднять на уровень выше чем уровень базы воды, скажем для душа без матора если это возможно
Two areas of doubt, firstly about the intake pipe is there a nonreturn valve attached, secondly, the improved version with the extra plastic cylinder is to keep the vacuum pressure constant, thanks for your return feedback?
It is my pleasure
The intake has a non return.
The non-returnvalve was the secret! I was almost certain ! Thanks
Its NRV... that hold back the water against gravity in the intake column. And the whole principle is make storage tank vacuum tight. The drum volume also act as storage buffer to maintain the constant flow..
When you open the outlet valve, water rushes in due to level deference though the drum outlet. And this creates vacuum in the entire supply chain connected to inlet water column. The vacuum then sucks the water thru water column NRV from river or bore well ( as the inlet). Thus maintaining the flow. Pl note, outlet flow pipe dia must be smaller then inlet pipe.
@@bharatkukreti8449 No, they used an outlet about the double diameter than the inlet. You will find the diameters used in some commentary above.
thanks for your update and very detail,,, i will try tomorrow and will ment my result ..
Woo I am going to use this idea in my form. Thanks
Most welcome 😊
If you add an inner tube from a bicycle to the air tank and inflate it it will increase the water pressure outflow as the air in the tube acts like a spring and helps push the water out with greater force
Sorry Dan, you are way out. There is no need for those tanks. You could as well use a larger main barrel. In any case, the output must be lower than the source.
Thanks once again for having your update on free water system installation and your team and partner, hope I can do it with my self using your techniques, I have a question regarding on your check valve Sir, I mean is that one package when you buy it at the hardware or is it you combine two items to make that check valve. Because I went to the hardware but I can't find the item you used in the system. Please reply and thank you, more power..
you could not use soft barrel
From where we can order that you called check valve that you soak in the water
we call that device a "foot valve" here in northeast US and it is one piece from the store. maybe that helps?
@@LearnForideas ... you are right 👍
Hi, I have a suggestion. You may put a pressure gauge near the pressure air tank inorder to determine how strong the pressure.
I think pressure guage won't work, the system is working like a siphone, so it has no pressure but it has a vaccume effect, vaccume gauge will do the work.
@@carlitomadrona6211 ... I think 🤔 you are right Sir 🙏💐
@ MABIRU channel .... welcome all innovative ideas 🙏💐
i have tested this and it did not work.
@@toto_elio477 that's why you didn't upload your test. since you're upload also didn't work. haha
Brother I appreciate your invention. Congratulations
I watch the first video presentation. I catched and understand the principle immediately. My brother is a water driller and build and construct a lot of pump. Thanks for sharing this. I can iliminate my water pump and electric motor.
please check the process again friend
I gonna try to make small electricity like you did for my house 👍
great and have any support please sir,
Hi I love your vdo and look so natural man
I don’t know how to express my feedback but you are awesome for this vdo may be you could make more EP such as additional some gravity support that could make your design give more productive
I will try my best
i watched the other clip ....the explanation is that one need to fill the water all through the system no matter what, opening valves needed at the beginning and at the end of the system as well as in the middle. the concept is negative pressure occurs while you open the valve on land. negative pressure will draw water from the pond to fill up the tank.
The water level in the river must be higher than the outlet to the field. The rest is details. In fact you do not need any drums at all, just a hose or a tube.
Thanks for sharing next time I will try to make it
Thanks for the lesson, my Qn is, what is the use of that air pressure container along the out let pipe for the irrigation?
out let 60mm and inlet 34mm
The air pressure pipes and tank has 2 uses; 1) To trap any air coming from the outlet valve , and 2) To increase the force/pressure of water output.
@@compostsfertilizers5471 Nice answer, but how do you explain that it increases the outlet pressure?
@@dettyouy223 The air that manages to enter through the outlet pipe, trying to go to the main vacuum tank will enter the vertical pipes pushing the water in there hence forcing the water down.
@@compostsfertilizers5471 good idea thank you.
this fantastic,thank you for this new technic,
Glad you like it!
Good job, We need a video with 50mm underground pipe inlet .. please as I don't have a river near me.
Great suggestion!
Oh Super idea How much deeper we can lift water please tell
4metters
It ' s a very clever idea.
The pumping system made by air pressure
Energy for free .
Thank you guys
The only way for this to work is if the out line is very large. The drop will make a vacuum pulling on the drop line or in line it should equalise and stop running. But is worth experimenting with. If you do please make a video so we can see your results. I use the air lift method. It uses atomized water and air to lift. It's lighter than water alone. It will float and bubble into a cistern.
outlet pipe from the drum should be minimum 2.5 times water inlet diameter and then reduced again at the end of the outlet run to increase pressure if needed
@@dano5562 Nah. You've been fooled. The outlet is actually lower than river water level. All you you need is the initial suction to get the flow going. A bit like you would do with a hose that goes up and then down.
@@accaciagame1706 that is not correct... look again. Think of a boat motor drawing gas, from tank, if the tank has no bleed valve the tank will draw a vacuum. that pipe from the river is the filling pipe(aka vacuum fill inlet), the higher we have to lift the water from river more vacuum!!! untill you can even sqaush the drum, this works upto 30 ft!!! if drum is strong enough and holds enough water.
Me too am thinking on the siphone effect in that the outlet is lower than the inlet position. Because siphon works only if the outlet is in a lower than the inlet water level.another point i want to understand is in many similar videos, i observed that tge barrel should be full of water with out any air. If there is air i think it should not work. So i need these two explanations
You have to think the engineering side of the system. The drum is acting as the pump. It does not matter if there is air or not as long as it is sealed after being filled with water. The outlet pipe need not be lower than the water level in the river. Once the outlet stopcock is opened water will flow out, creating negative pressure in the drum. This will in turn suck up the water in the river into the drum and out thru the outlet pipe.
Hi. Thank you so much for this. Very helpful . Can I request for the list of all materials you used? Thank u so much and God Bless
see this youtube video : FREE ENERGY Water Pump FULLY EXPLAINED!! REAL OR FAKE?
Eternally flowing water - The truth about eternal flowing water without a pump
Yes
@@simonmwelwa6203 Yes ???? yes what ???
Vean más videos relacionados y verán que esto es una farsa
Great tutorial!
Thanks Much!
ini baru tutorial yang bnar dan sangat bermsnfast
Little question ser how many valve did u use. only the one that put in the river or did you put also in the air tanks.?
I think it will work if the water source is at the level of the or higher than the rice field.
Very clear explanation
Thnk you
thank you too
Sir I am from india. Big fan of you. Plis surely answer my question. I m going to test it. My question is volume of outlet water is bigger than inlet, so at certain time the tank will be emptied, what will happen than. Wil this work continuesly until and unless there is no leakage and we deliberately stop it???
You have to put reducer at the end of the oulet same size as the inlet.
Nice 👍 work
Question is the rice field lower than the river or above the river or the same high?
Thanks
Source must be higher tan output at the rice field. This is a siphon.
Thank you bro for your videos. KEEP MAKING INFORMATIVE ones!! keep safe.
Thanks, will do!
Notpossble
恭喜..成功利用到自然物理虹吸管原製作到環保/不再使用石油污染地球..多謝分享..💯💢
Are u still using the standard 3/4 pipe vent hole in the barrel or Are u putting a bigger hole for the intake.
Prachtig werk, ik heb het met plezier gevolgd.
Thank you for leveling up the free energy water pump...may I request the list of materials needed in the installation of the pump especially the inlet pipe... I can hardly understand that part.
So here he has a drum. Then he has a three valve setup hooked up to the drum. One valve is on the bottom and there are two valves up top. Bottom valve has a pipe after it with a tee and a pipe coming out the top of the tee with a cap on the end of that pipe. The other open end of the tee has another length of pipe and a valve on the end. The First top valve is for air venting, it is located at the back. In the front, closest to source water is a 45 degree bend attached to an elbow coming off the valve. At the 45 degree bend, a pipe is installed to reach the source, this is the inlet. An appropriate filter may need to be installed, as debris would accumulate inside the drum over time. In this particular configuration it can be used without a filter and free flow is used to flush the drum continuously. The water is from a stream that is not very muddy at all. This system is expected to run without clogging for a number of years, until repairing the leaks and possibly changing the drum is required for preventative maintenance. Use ptfe thread tape and ball valve replacements if required. Joiners can be used to repair sections of pipe.
@@thomasknight-wagener6630 .... sir... Happy 😊 to read your knowledge and comment... you are so good and kind-hearted person too ❤️ 🙏💐
From philippines your so great..here..because of your ideal ..😊😊😇thanks for sharing..help me please..i try this install in my pond
How can I help you?
Sir gumana b?
Thanks for Sharing the information Watt is the piece on the end of the pipe in the river called
Foot valve, one way valve, check valve. Not needed if you use a barrel.
Your masterpiece will help us brother.
The videos are always informative. Nice to see talent passed down to the youth.
Can I use this with a 13mtr well? What's the best height for the drum installation?
DEAR FRIEND! THIS SISTEM Works to Atmosferic Pressure (1,33kgf /cm2 to sea water level). We have loses in the sistem ...THESE loses are praticam limits in 8 meters of water column.TANK you !
No, impossible. A siphon can not lift any water, not even 1 inch.
thanks for sharing your very good idea
we most welcome to share
If your drum has air in it, then your pickup line is leaking. There should be no change in the water level in the drum. The water level should remain constant and the pump will run forever.
This siphon. will only run if the water level in the river is higher than the output to the rice field.
thanks for sharing your ideas
World needs not only water drawer from water sources but also water
maker ( near future ) .
ให้ความรู้ดีมากจ้า
It is just a modified siphon. A siphon uses gravity with an outlet than the inlet. It is not a free energy machine. It is not a pump either, though an innovative way of transferring water.
Put a sight glass ( or any transparent hose) on a drum to monitor the level of the water ... that would help on upgrading your project....
No need. You can hear the height inside by taping with a finger on the drum. The sound will change around the water level.
@@dettyouy223 ... you are right Sir 👍🙏💐
Already our Bangladeshi people are starting this project. Inshallah I’ll make this one very soon
Excellent brother thank you for sharing 👍
Nice one I learned. Thank you for sharing.
That is nice and will be a big help fir a farmer like me. Can you share me the parts and exact measures. Kudos and more happy farming!
Very good job I want to follow this
Thank you for sharing buddy. Have a good day
Thank you too
Please explain well and show what was the equipment you put in the end tube of suction one?
please see my previous Videos about explanation
And this really works 24×7 or it stops after few hours 😁
yes sure
Im sri lanka.good a work
Tjank you for sharing. Can we use bigger pipe sizes like 120mm for discharge and 60 mm for intake pipe?
No try 63mm inlet and 50mm outle
Verry nice i will try that what i need what materials need.
Do not try if your water source is lower than your output. No siphon can lift water up.
Good idea bro for formers....!
yes sure
your ideas comes in so handy. We need it in our place. Please advise the name of the parts we need. 🙏
ny tube will do. But remember, inlet must be higher than outlet for this siphon to work.
Well done, but i think there is no need for the drum, but only pipes would do the work. Since the elevation of water as source is higher than the elevation of the output, it would work. But if the output elevation is higher than the source, it would not work without using a pump
bro can you make a video for aquaponics system this is set up is a very helpful for aqauanics farming
Sure I will
Thanks for sharing this video
You welcome
what is the size of your output and input pipe,, thank you so much..
input 34mm and output 60mm
very nice experement.
Thank
Bonjour et merci pour la vidéo. Quelle est le rôle du bidon et a quelle distance du tonneau il doit être. Merci.
Le bidon sert à augmenter la pression dans le système. Je pense que la distance importe peu mais de préférence plus proche du tonneau que de la sortie pour augmenter la pousser
@@alassanebassiti3630 Est-ce que vous avez une idée du principe qui augmente la pression de sortie ? Je comprends que ça capte les petites bulles d'air mais ça n'explique pas à mon sens l'augmentation de la pression de sortie. Si la pression d'air augmente dans le bidon, ça va provoquer l'échappée de cet air en trop !
I will try this way, i hope its really work
Just to be clear. This is not a pump, it is a siphon. The drum it to prime the system (fill it with water). The pressure at the outlet (if closed) is the difference in height between inlet and outlet. And of course the outlet must be lower than the inlet. If you could fill it with water a pipe along the ground will work just as well.
No it is not a siphon but a pump. Scientific logics are pushed aside here. Let me just say "It's an insult to physics 🙃🙃🙃 ".
@@compostsfertilizers5471
There is nothing insulting here. But if you consider it a pump, where does the energy to pump water come from?
If the answer is gravity, and there are no moving parts, it's a siphon.
@@AldriFerdig It's a vacuum system. Water is sucked from the river due to the vacuum created in the drum. the force of the water in the outlet stops air from sipping back hence water from the river raises to the drum.
@@compostsfertilizers5471
Apart from the detail that it's more correct to say that it's the air pressure that pushes the water into the drum, and further until it runs downhill, your description is correct.
This is how a siphon works.
Btw. there are no vacuum in the drum. A siphon can be used to lift water about 10 meters high, as long as the outlet is lower than the inlet. The limitation is that one atmosphere of pressure equals 10 meters of water.
If it could pump water to a level higher than the input it would not be a siphon, but this system is a siphon. A hundred drums between the inlet and the outlet doesn't change this.
There are gravity powered water pumps, but this isn't an example of one of those.
@@AldriFerdig May dear these guys a pulling water more than 20feet under ground. And this is now practiced in many countries in Asia, Africa and Latin America. So please stop this unnecessary arguments.
Thanks for sharing bcause Im verry intresting
unless the outlet is lower than the inlet, otherwise, once pressure balance, it will stop running.
Not stop because input pipe and output pipe is same pipe size and have a strong and big drum if middle
@@LearnForideas Sorry, wrong information. Diameter and lengh of input and output is not critical But, input must be higher than the output. It is a siphon.
If you add a RAM Pump at outlet then it will be possible to pump water higher and farther away from source.
You are genius. What a great idea
hi sir, thank you for the video, Does this setup run 24hours with continous running??????? please reply
It's a siphon powered by gravity. As long as there is water at the intake, and there are no leaks, it will run forever.
@@AldriFerdig .... thanks for your kind information and comment 🙏💐👍
Broder cguro maghihinto ksi mas malaki ang outlet na pipe kaysa in...mauubusan...
@@prensedlan3178 i dont know which language u r talking about, can you please translate in english. Even google translator is not recognising
Are the 2 air pipe both closes from above ? Are there flappers or not?
In Thailand have flooding come soon, can i use this for helping pump flood water away?
Must the tank be near the source of water or can you have it next to your house and have the inlet pipe run some distant to the source of water?
yes sure we need to keep near Water source
Thanks for sharing my question is how about am using deep will water about 40ft feet deep but the water level is 30 feet it is ok
It is ok?
Deep only 3-4meters
thanks from Meghalaya India
Brother this pump works for Good so the maximum hight how much is working please reply me brother thanks you 🙏
depend on you drum and output pipe
Water is d work of those vertical pipes?will it work if their valve are open?
Hello, thank you for sharing this kind of project. I am writing to you from Azerbaijan, please answer. What is the approximate length of the outlet pipe?

The outlet can be as long as you want provided that it slopes downwards to keep the momentum and maintain a "pulling" force
@@RailCartAdventures Actually the output can go up and down, up and down, but the source, a river, must be elevated higher than the outlet.
For this siphon to work the water level in the river must be higher than the output to the field. With a foot valve at the input, no blue barrel is needed. No need to lift the barrel that high, only makes it more difficult to fill. No need for marer valve just at the output from the drum. No need for white container. No need for the vertical pipe.
In short, one simple tube can do this. All the rest is just to get the tube filled with water.
What is a good maximum height of drum "stand" (wood) ..
And what is the maximum length of draw pipe from river to the drum possible?
Thanks.
3-4m
It is a siphon. As long as the outlet is lower than the inlet the middle part can be up to about 10 meters, as that is the water column corresponding to one atmosphere pressure.
There are no absolute max lengths, but friction will eventually make it stop depending on the size of your tubing.
@@AldriFerdig ....👍🙏💐
This upgrade is better . Nice
I feel so impressed to Link up with people of great minds. my question is that what if I put several air bags along the bigger outlet pipe,will it increase the discharge pressure
and also the standing long pipe,is it enclosed or opened because if it's closed, I think this necessitates putting a valve at the drum outlet because pressure in enclosed fluids is equally transmitted through the fluids. this means that without valve at outlet of drum, some water might be forced to go back into the drum once. thanks
No tanks along the output pipe is needed. Only waste money. Dip the exit end into a bucket of water to prevent air leakin in from the outlet.
Thanks bro..i try to copy this..please help me .all materials we need...so that i buy all of in the..store
ok thank