My TV did this so went out and bought a new 65 inch costing $4000 and the next day did this and it worked. Wife wanted to keep the new TV so have this in the man cave now
This is gold! Ive had backlight LEDS slowly going out for a while, and today; the whole lower right decided to fail and tripped the error. THANK YOU!!, a very simple fix! My backlight is still stuffed; but at least i now have time to shop around. Thanks again!
@@WAJU4for future post readers: YOU NEED TO GROUND THE WIRE to the chassis using a screw or solder after you cut it OR you can ground the wire by using an empty pin slot on the connector. YOU CANNOT JUST CUT THE WIRE and leave it!
Be careful taking off the back cover, I accidently pulled the electrical wire off the circuit board. Had to have a friend solder it back. Other than that this fix worked great. Saved a $4000.00+ TV from the garbage. And Sony WTF is wrong with you guys? Why would you design a great TV to crash over a few bulbs? TY Will's TV!
It may not work 100% of the time, but it's worth a shot. I just tried this on my friend's KDL-60W850B and it seemed to work great with the screen showing "No HDMI signal connected. I put the back on and powered it up, but after 60 seconds with a picture, it down and went back to 4 flashes again. Any other ideas?
Thank you. This seems to be working for me as of right now on a Sony Bravia KDL-60NX720 that had the 4 blinking lights. I still have a slight dark area in the lower left quadrant, but not always all that noticeable. Fine for a spare set! Thanks again.
Hi,does this solve 8 blinks? I’ve tried clearing vents etc and disconnecting devices. My tv stays black screen, white light led tries then eventually starts blinking red. Help please
@@akshatjayswal5601 no it doesn't work. I tried the hard reset where you push the on/off button alongside the volume down button and did it 5 times but it never worked
Those in Sydney Australia - if you have proof of purchase . Call Sony and go down that channel, I was quoted $900+ by there repairs team who came out to look. I called Sony back and said it’s a common fault, I’m not paying for it. Tv panel was replaced free of charge, had all scratches and chips on screen also which was apart of the panel so WIN WIN WON 🥇
I think my Sony XBR55HX950 TV is 5 blinking lights can this fix this issue the same way I replaced the T Con board and still not coming on just 5 blinking lights after the green, also my BBl _Error code is on the first row third down from the top unlike yours which is second row down one, which wire should I pull out?
@@VMC954 It worked for me for one month and had to replace the T-con board eventually. Another workaround is once TV works with hair dryer method don't turn it off, just turn off display from action menu when TV not in use.
I got a newer model sony tv 65x950G I tried this trick did not seem to work. mine also have 4 blinking red light. they seem to have changed something, I get the red blinking light at the LD driver board and also at the front of TV sony LED display. any idea ?
I have a Sony Bravia KDL40R470B TV it is giving 4 blinking lights, i changed the TCON board but still no picture, i am told the problem could be the back light, is there any fix for it ?
I having same issue my tv model is Sony xbr-65x900c and when I try to put hdr leds lights start blinking like they running out of power then the tv completely shut off itself and start blinking red, do you know what the problem could be? Also when i turn on the tv and touched like to make it move lil bit it shut off too and start blinking red
I’m just one person who knows very little about what component goes where or if the software has an issue, or even where to buy parts! So I’d say it might be easier (since Sony offered no help) to buy another TV. This time it definitely will NOT be a Sony. I only had it 2 years, rarely used it, and it quit. 😡 so mad.
Thanks, worked on 65X850B. Are there long term consequences of this bypass? Prior to this, I noticed that if i disconnect the cables from the main board to the TCON board, the TV would stay on. Couldn't pinpoint the issue, though.
Thanks very much. The hack got rid of the 6 blinking red lights but I still can't see the screen although I can hear the music clear as day. Any ideas ? Thanks
@Wil's Tv Yeah I think you are correct. I've installed the latest Firmware via USB and now I can see the picture if I shine a flashlight on the screen which tells me the backlight has gone. I've also read somewhere that 1 single faulty led will be picked up by a sensor and shut the whole backlight down instead of just shutting off the faulty led. Do you know if there's a way to bypass that sensor that picks up the fault in the back light ?
What happens if BL-ERR is not grounded just disconnected? What if the other wire was grounded and not the one that was grounded? Sony KDL-40EX500 with 6 blinks. Tried an eBay backlight board, same problem. Disconnected the BL-ERR wire, same thing. Just wondering if it matters which wire is grounded and if the wrong one is grounded if that will cause damage.
@@wilstv Does it matter which side of the cut wire is grounded? Cut wire Going out from the power supply or cut wire going into it? could it also be my ambient sensor in stead? I have ccfl back lights. A bad ccfl would not short like a bad led.
What model is this TV, because l have a Sony 70 screen Just want to make sure l cut and ground the right wire. If you can respond My model is SONY KDL 70W830-B Thanks
@@wilstv Thanks for the fast response, They share the same power board as 70w830-b Tomorrow l will try grounding that wire, hopefully it will stop shutting down
Hi there, I had success doing this 3 or 4 months ago and the same problem has started again (4 red blinks) 😣 is there anything you can recommend please? Thank you
@@ShadowbannedbyTH-cam i had 4 flaahes (and 1.6V on BL_ERR while connected) I cut the BL err signal wire, and it turned to 6 flashes (with 3.3V on the controller side.) After grounding BL_ERR from the controller (as shown) the TV works. Still has backlight issues that caused it to shut off; but atleast it runs.
Need help.... I have the XBR-85X900H and I'm having the same problems, but my bl_err is connected to a double row plug, and shows it's the #1 wire. Not sure which one is #1.
@@wilstv I believe I understand now after watching your video a few more times are diagram is similar. 1-27 is my bottom row and 2-28 is the top correct?
If red led blinks 6 times..its LED backlight..replace backlight strips. Try...replacing backlight strips...Bec it is a Backlight LED Strip problem...one set backlight LED strips is about $20...difficulty is Average..careful removal and recording of all screws etc to replace exactly the same way is important...Also best to replace the whole set of LED strips..don't do onlybthe Spoilt ones...bec they work in synchronization...any small voltage difference can cause a shutdown.. Use youtube videos that show how to do it as a guide...takes about 2 hours to get to the strips..if untrained...make sure the TV is switched off ...for more than 24 hours...and press switch on when unpugged to discharge as muchbas possible....and don't touch the capacitor..HIGH VOLTAGE SHOCK danger!!!
blink error code can have quite a few different causes. Ranging from the T-con board to the panel and few things in between. If you have the original TV remote than try to see if this will work on your set: 1. In standby mode, press the following buttons on the Sony remote: DISPLAY....5....VOL(-)....TV POWER 2. On the left side are the blink codes. On the right hand side is the error count. 3. Under 005, you'll see three listings... TCON, HFR, and P-ID (panel). 4. Let us know what errors your set shows. If that does not work on your set, then you will have to remove the back of your TV and check the boards. Try to rule out/in the T-con board as faulty. Disconnect the LVDS cable to the T-CON board, the cable between the Main board and the T-CON board, and see if the error code will change. Let us know what the result is.
I have an xbr85x850d that shows 8 red blinking lights, tried reset and everything. Im gonna try what you did in this video but my tv has 2 powersupplys and multiple connecters with BL_ERR which ones do I ground? Thank in Advance...
try this Clean any vents/slots in the TV cabinet Make sure there is room for air to circulate around the cabinet of the TV. Turn off the TV and unplug all devices connected to the TV Turn off the TV and disconnect all connected devices. With all devices disconnected, turn on the TV again and check whether the LED blinks. If it does not blink, the issue may be in the connected devices
@@wilstv thank you bro 2017 sony bravia 32 inch sken... iba ung board sken,ano fb acct mo bro? send ko picture sana if okay lang sayo.. 3 blinks sken nag off din,may detrected error din malamang
This is not a genuine fix !!! This is literally just a botch it fix that will eventually blow the LED back light driver chip. All you are doing is literally bypassing the tv’s self diagnostics & error code program but as the bad LED is literally still there and not replaced the driver chip will be Working overtime to supply voltage to the bad LED to light it and with no error detection will keep upping the voltage until either the driver chip blows or the power supply gives up. The only real way to fix this is to strip the tv down, remove the screen and diffuser panels to get access to the LED array and replace the strip with bad led/s.
Got this same problem on my XBR-55A1E, TV shuts off after a few seconds and I get 4 blinking red light flashes over and over. I've tried the procedure to unplug it and hold the power + volume down and turn it on until I saw the green light and doing the factory reset but still nothing. After that it would just shut off again and again. Also tried to do the Firmware update manually but it was unsuccessful. I got some more chance to fix with this video th-cam.com/video/TSgqb_7HO9I/w-d-xo.html but haven't tried yet... It looks similar fix as Wil's video. Any thoughts let me know. Thanks!!
yeah it coz by bad led backlight.unless you want to dis assemble the whole tv glass and buy the replacement it will be good.for now this is kinda easy fix if you dont want to do the whole repair of the tv.
@g a Thanks for your reply. It started getting some two or three vertical lines (no big issue) and after few weeks it started to shut down with the 4 times red light blinking. Sometimes the TV keeps working for a while but most of the time it shuts down itself.
Ernesto M, I am in the same boat as you with the 65-inch version of your TV. I saw another video with the same fix (search big dog) for the previous Sony OLED generation, so there must be a similar fix for the second generation OLEDs. Unfortunately, the PC boards are no longer labeled with the pin out legends. I am slowly working through pulling out each wire to identify the BRR_err??? wire....pita
4 blink code means either the backlight inverter board is bad or one of the backlights in the LCD panel has failed. It can also be the LD board or main logic board, check inverter board wires for arcing to ground
I've taken my tv to the TV repairs like 3times in 6 months and it keeps doing the same thing its really time and money consuming and the repairers are just not doing there job properly I recon they're just making money off me
Really need help its just passing me off I spent alot of money on this TV 75 inch kdl-75w850c beautiful TV i almost wanna give up on it but your help is needed ill try this out and fix it first before I make another trip too the repairs or buy a new 9ne
![เปิด อาณาจักร หมื่นล้าน "สาระตั้ม" l [Nickynachat]](http://i.ytimg.com/vi/3XE0nPF4YkQ/mqdefault.jpg)
My TV did this so went out and bought a new 65 inch costing $4000 and the next day did this and it worked. Wife wanted to keep the new TV so have this in the man cave now
This is gold! Ive had backlight LEDS slowly going out for a while, and today; the whole lower right decided to fail and tripped the error. THANK YOU!!, a very simple fix! My backlight is still stuffed; but at least i now have time to shop around. Thanks again!
Same with me happened today
@@garvwasson9416 wait so basically all you need to do is cut the LED wire thats causin the problem and thats about it?
@@WAJU4for future post readers: YOU NEED TO GROUND THE WIRE to the chassis using a screw or solder after you cut it OR you can ground the wire by using an empty pin slot on the connector. YOU CANNOT JUST CUT THE WIRE and leave it!
Be careful taking off the back cover, I accidently pulled the electrical wire off the circuit board. Had to have a friend solder it back. Other than that this fix worked great. Saved a $4000.00+ TV from the garbage. And Sony WTF is wrong with you guys? Why would you design a great TV to crash over a few bulbs? TY Will's TV!
I have a 2018 model XBR-75x900f doing the same thing. How long wil the tv last and will it look the same after doing this fix? MANY THANKS!!!
So far my tv still working. There will be some dark area
Thanks a Lot Will, greetings from valparaiso, chile
Welcome. Thanks too🤗
Hi Wil, Thanks, this is how I can impress my neighbours with their broke tv! Well done...I have made the modification and it Works perfectly! Subbed!
Thanks man.👍👍
It may not work 100% of the time, but it's worth a shot. I just tried this on my friend's KDL-60W850B and it seemed to work great with the screen showing "No HDMI signal connected. I put the back on and powered it up, but after 60 seconds with a picture, it down and went back to 4 flashes again. Any other ideas?
it might need new power board.
@@wilstv Or it's time for a new TV. Not Sony!
Thank you. This seems to be working for me as of right now on a Sony Bravia KDL-60NX720 that had the 4 blinking lights. I still have a slight dark area in the lower left quadrant, but not always all that noticeable. Fine for a spare set! Thanks again.
I dont see that section on my power board that specifies what wire is what.(Bl err) would it be underneath the board? I have an lg a8g
Mostly they are on the side near the connections.just look for an image of rectangle with numbers.
Hi,does this solve 8 blinks? I’ve tried clearing vents etc and disconnecting devices. My tv stays black screen, white light led tries then eventually starts blinking red. Help please
8 Times Blink - For certain models, a special reset procedure is needed if the Red LED on the front of the TV is blinking 8 times and then repeats.
@@stinglikeab8801 yeah, I've tried it and it didn't work?
Is it working now ? I tried but no use
@@miggystoon7892 ?????
@@akshatjayswal5601 no it doesn't work. I tried the hard reset where you push the on/off button alongside the volume down button and did it 5 times but it never worked
Those in Sydney Australia - if you have proof of purchase . Call Sony and go down that channel, I was quoted $900+ by there repairs team who came out to look. I called Sony back and said it’s a common fault, I’m not paying for it. Tv panel was replaced free of charge, had all scratches and chips on screen also which was apart of the panel so WIN WIN WON 🥇
I think my Sony XBR55HX950 TV is 5 blinking lights can this fix this issue the same way I replaced the T Con board and still not coming on just 5 blinking lights after the green, also my BBl _Error code is on the first row third down from the top unlike yours which is second row down one, which wire should I pull out?
Nice . but if 4 red light blinking surely need to take the procedure you did ? They no need to restart .?
a 4 blink code means either the backlight inverter board is bad or one of the backlights in the LCD panel has failed.
Plss tell me if the wire u cut . Have names in the connector . To connect in the board ? What line number you cut sir ?
does it work for sony X75H and only for old model?
Used hair dryer for 5-10 minutes to blow hot air in vents on back panel and tv started normally without 5 times red light blinking
This worked for me thanks!!
@@VMC954 It worked for me for one month and had to replace the T-con board eventually. Another workaround is once TV works with hair dryer method don't turn it off, just turn off display from action menu when TV not in use.
Thanks, this worked for my Sony.
@@anthonybairstow7155 permanent solution is t con board replacement
@@Balkeet007 thanks, I guessed it was a temp. solution.
I got a newer model sony tv 65x950G I tried this trick did not seem to work. mine also have 4 blinking red light. they seem to have changed something, I get the red blinking light at the LD driver board and also at the front of TV sony LED display. any idea ?
Thank you for much...it's work on sony kdl-55W954A...beautiful...good job
Glad i help.thanks
Any idea on what a 3 blinking light error would mean on a kd-55xe9005?
I have a Sony Bravia KDL40R470B TV it is giving 4 blinking lights, i changed the TCON board but still no picture, i am told the problem could be the back light, is there any fix for it ?
if theres no flash of light of led if migt be the main board
I having same issue my tv model is Sony xbr-65x900c and when I try to put hdr leds lights start blinking like they running out of power then the tv completely shut off itself and start blinking red, do you know what the problem could be? Also when i turn on the tv and touched like to make it move lil bit it shut off too and start blinking red
I’m just one person who knows very little about what component goes where or if the software has an issue, or even where to buy parts! So I’d say it might be easier (since Sony offered no help) to buy another TV. This time it definitely will NOT be a Sony. I only had it 2 years, rarely used it, and it quit. 😡 so mad.
Thanks, worked on 65X850B. Are there long term consequences of this bypass? Prior to this, I noticed that if i disconnect the cables from the main board to the TCON board, the TV would stay on. Couldn't pinpoint the issue, though.
so far my tv still working fine untill now.
Is there a way to contact you Will i need some advice please
you can msg here.
Thanks very much. The hack got rid of the 6 blinking red lights but I still can't see the screen although I can hear the music clear as day. Any ideas ? Thanks
If might need to change the whole led assembly.
@Wil's Tv Yeah I think you are correct. I've installed the latest Firmware via USB and now I can see the picture if I shine a flashlight on the screen which tells me the backlight has gone. I've also read somewhere that 1 single faulty led will be picked up by a sensor and shut the whole backlight down instead of just shutting off the faulty led. Do you know if there's a way to bypass that sensor that picks up the fault in the back light ?
Is the connector labeled as to which pin is what?
Led bL err
Genius, it works!
Works. Thank u
What happens if BL-ERR is not grounded just disconnected? What if the other wire was grounded and not the one that was grounded? Sony KDL-40EX500 with 6 blinks. Tried an eBay backlight board, same problem. Disconnected the BL-ERR wire, same thing. Just wondering if it matters which wire is grounded and if the wrong one is grounded if that will cause damage.
You must ground the bl err wire. it needs a signal.
@@wilstv Does it matter which side of the cut wire is grounded? Cut wire Going out from the power supply or cut wire going into it? could it also be my ambient sensor in stead? I have ccfl back lights. A bad ccfl would not short like a bad led.
What model is this TV, because l have a Sony 70 screen
Just want to make sure l cut and ground the right wire.
If you can respond
My model is SONY KDL 70W830-B
Thanks
sony 70x850b
@@wilstv Thanks for the fast response,
They share the same power board as 70w830-b
Tomorrow l will try grounding that wire, hopefully it will stop
shutting down
I find a wire name LD-err, should i cut that one?
try to find again the bl err wire..if not thats probably it.you can simple connect it again if doesnt work.
BL_ERR wire only will work
It works!! Thanks very much from Uruguay!!
youre welcome.if you can support my channel.its really appreciated..thanks
Please can I use this method on my Sony kdl-46w905a Bravia tv?
you can check if you see that wire on your board..but as far as i know all sony have this same configuration.
@@wilstv Thanks a lot , I’ve tried eliminating the BL-ERR cable and I think the problem is solved bcos the Tv is working for the past six hrs.
Hi what exactly Wire should I should I cut
The one that with the BL_ERR written on it.
Does it work on the Oled tv? I have the Sony XBR-65A9G. Red light blinks 4 times too.
it might.try to open it.
Hi there, I had success doing this 3 or 4 months ago and the same problem has started again (4 red blinks) 😣 is there anything you can recommend please? Thank you
you might really need to replace the backlight.
Thanks man, it works perfect 👌🏻
Greetings from Germany
Thank you
What about 6 lights flashing? I did a simple reset more than 10 times. It still cuts off.
i havent encountered that yet.ill make one as soon as i have one.
Same here....
@@ShadowbannedbyTH-cam i had 4 flaahes (and 1.6V on BL_ERR while connected) I cut the BL err signal wire, and it turned to 6 flashes (with 3.3V on the controller side.) After grounding BL_ERR from the controller (as shown) the TV works. Still has backlight issues that caused it to shut off; but atleast it runs.
@@forestR1 hi Forest. I have 4 blinks too. Did it work so far?
@@andresvaldivieso9412 yes.
Vhai amr sony tv same problem red light 5 bar on off hoy er karon ki back light problem? Janaben plz?
Need help.... I have the XBR-85X900H and I'm having the same problems, but my bl_err is connected to a double row plug, and shows it's the #1 wire. Not sure which one is #1.
check the diagram.usually it shows which is #1 look.on the board..mostly is close by near the pins.
@@wilstv my diagram shows a 2 above the number 1 near the left side of the connector, does this mean the one to cut is the bottom wire on left?
@@wilstv I believe I understand now after watching your video a few more times are diagram is similar. 1-27 is my bottom row and 2-28 is the top correct?
If red led blinks 6 times..its LED backlight..replace backlight strips.
Try...replacing backlight strips...Bec it is a Backlight LED Strip problem...one set backlight LED strips is about $20...difficulty is Average..careful removal and recording of all screws etc to replace exactly the same way is important...Also best to replace the whole set of LED strips..don't do onlybthe Spoilt ones...bec they work in synchronization...any small voltage difference can cause a shutdown..
Use youtube videos that show how to do it as a guide...takes about 2 hours to get to the strips..if untrained...make sure the TV is switched off ...for more than 24 hours...and press switch on when unpugged to discharge as muchbas possible....and don't touch the capacitor..HIGH VOLTAGE SHOCK danger!!!
my kdl40nx710 also red led light blink 4 times. im from malaysia. where can i get replacement part for it?
It really works!!!! Thank You 😇
welcome.glad i help.
R u serious
How's this an easy fix?
Wow galing....
Hi Wil
I tried this method , the problem still exist . Can you help me out and check if I did it correctly. I can send a image or video
How many blinks does your tv show?
Thank you WoW you are the best
Yo can you help me bc I need clearification
TV fixed.. thanks so much!
can help me sir my sony kdl-55hx750 have 2blinks
does this fix 6 blinking red lights?
I think is just simple reset for the 6 blinking lights
@@wilstv how to do Simple reset 🙁
@@MadGasher Sony will send you a pamphlet on hw to reset the TV call them
I did a simple reset more than 10 times. It still cuts off.
Thank you! It worked perfectly!
it helped a lot, thank you very much !!!
Does this work for a KD-55X8500C?
you can try opening it.if it has same wiring. or have a bl_err wire.
Hi I followed what you did, but now bottom left corner of screen is alot dimmer then the rest of tv?
is just a temporary fix. because you have to replace the busted led inside. which is lot of work.
Thanks a lot.
What about 5 flashes
dont have experienced with that yet.ill make one once i have.
Did you find out what’s happening? I have 5 flashes also
Same figure it out?
Would you happen to have a email I can send a picture of my diagram and connector/wires?
maybe make a short video of it and ill take a look where is the bl err wire.
@@wilstv I just uploaded the video. You'll notice I cut a few but only tried to ground the white one to the far right.
@@wilstv th-cam.com/video/uZ5pscn8c2Q/w-d-xo.html
i saw the Bl err wire..just cut that one.and connect a extended wire to the ground screw.
@@wilstv is it the bottom left White wire?
hello bro I was trying with Sony kdl-55w808a but I have the same red blinking 5 times. please I need your help
blink error code can have quite a few different causes. Ranging from the T-con board to the panel and few things in between. If you have the original TV remote than try to see if this will work on your set:
1. In standby mode, press the following buttons on the Sony remote:
DISPLAY....5....VOL(-)....TV POWER
2. On the left side are the blink codes. On the right hand side is the error count.
3. Under 005, you'll see three listings... TCON, HFR, and P-ID (panel).
4. Let us know what errors your set shows.
If that does not work on your set, then you will have to remove the back of your TV and check the boards. Try to rule out/in the T-con board as faulty. Disconnect the LVDS cable to the T-CON board, the cable between the Main board and the T-CON board, and see if the error code will change. Let us know what the result is.
@@wilstv hello bro the screen of my tv are black. nothing can't see . you think I can do it with this black screen? thanks :)
If theres no light or blink.it might need new powersupply.
I have an xbr85x850d that shows 8 red blinking lights, tried reset and everything. Im gonna try what you did in this video but my tv has 2 powersupplys and multiple connecters with BL_ERR which ones do I ground? Thank in Advance...
@Wil's Tv
try this
Clean any vents/slots in the TV cabinet
Make sure there is room for air to circulate around the cabinet of the TV.
Turn off the TV and unplug all devices connected to the TV
Turn off the TV and disconnect all connected devices. With all devices disconnected, turn on the TV again and check whether the LED blinks.
If it does not blink, the issue may be in the connected devices
did u fix
i have red & black cables which one should i cut
the one which connect to bl_err wire.
5 times red blink ano po gawin? Kung palitan ng tcon board ok lang po ba?
baka po mhina po u voltage nea..try to plug in somewhere that has good voltage.if not try to change ng t con board.thanks for watching
Have the same problem here please help fix
HELLO CAN YOU PLEASE HELP ME FIND THE BLINKING ERROR CABLE ON KD65XE9005
Look closely on the board.you will find something like Bl_Err.and its close by the wiring connector with the marking of no.1 for your reference.
Man fuck these TVs I shouldn’t even have this problem
Suffering same problem what to do please tell me sony bravia W800 android.
It's not working I have done same thing but same problem. The model No is KD65X8509C sony tv
Mine is Sony Bravia 32inch, bro pano mo natukoy ung exact wire to cut? San mkkita indicator na siya ung error BL?
check un un diagram nea.tpos hnpin mo un saan muna un pin 1..nsa ktbi lng un ng ribbon.
@@wilstv thank you bro 2017 sony bravia 32 inch sken... iba ung board sken,ano fb acct mo bro? send ko picture sana if okay lang sayo.. 3 blinks sken nag off din,may detrected error din malamang
Helow.. I have the same problem .. 4 times red blinking of my Sony KDL-43w667G October 2021
Would this work for a KDL-75W850C model? Mine turns on shows the Sony sign for a few seconds then cuts off and goes to the 6 blink
it might need a reset.try searching how to reset the model of your tv.
Thanks, but it doesn't work for my Bravia KD 55XF9005 4K
Testing now, I think it worked!
Help
3 blink red light Sony kdl-42w800a
It mainly cause by power supply problem.just replace it and it will be good.
For me the green lights up but goes off again and then nothing more happens ???!
nice video bro
thanks hope it helps everyone
Hi” your not showing how to tape wire together , details please
I just solder it.the tape it with electrical tape.nothing special about it.very simple.
Thank you
This is not a genuine fix !!!
This is literally just a botch it fix that will eventually blow the LED back light driver chip.
All you are doing is literally bypassing the tv’s self diagnostics & error code program but as the bad LED is literally still there and not replaced the driver chip will be Working overtime to supply voltage to the bad LED to light it and with no error detection will keep upping the voltage until either the driver chip blows or the power supply gives up.
The only real way to fix this is to strip the tv down, remove the screen and diffuser panels to get access to the LED array and replace the strip with bad led/s.
Thank u, my tv ok.
Thanks worked 👍
Hi, I cut the wrong wire you should trust me tho.
if you cut the wrong wire.find a xtra wire that you can connect them again.
How to fix 2 blinking red?
its power supply issue
This does not work on 900f
Mantap teruskan upload videonya sama2 mendukung ya
Got this same problem on my XBR-55A1E, TV shuts off after a few seconds and I get 4 blinking red light flashes over and over. I've tried the procedure to unplug it and hold the power + volume down and turn it on until I saw the green light and doing the factory reset but still nothing. After that it would just shut off again and again. Also tried to do the Firmware update manually but it was unsuccessful. I got some more chance to fix with this video th-cam.com/video/TSgqb_7HO9I/w-d-xo.html but haven't tried yet...
It looks similar fix as Wil's video. Any thoughts let me know. Thanks!!
yeah it coz by bad led backlight.unless you want to dis assemble the whole tv glass and buy the replacement it will be good.for now this is kinda easy fix if you dont want to do the whole repair of the tv.
Hi Wil, I’m trying to find this wire but I don’t know where it’s located on my XBR-55A1E. Any idea? Thanks!
@g a Thanks for your reply. It started getting some two or three vertical lines (no big issue) and after few weeks it started to shut down with the 4 times red light blinking. Sometimes the TV keeps working for a while but most of the time it shuts down itself.
Ernesto M, I am in the same boat as you with the 65-inch version of your TV. I saw another video with the same fix (search big dog) for the previous Sony OLED generation, so there must be a similar fix for the second generation OLEDs. Unfortunately, the PC boards are no longer labeled with the pin out legends. I am slowly working through pulling out each wire to identify the BRR_err??? wire....pita
My sony android is in blinking 4 times a row, can someone walk me through please? Thaml you
4 blink code means either the backlight inverter board is bad or one of the backlights in the LCD panel has failed. It can also be the LD board or main logic board, check inverter board wires for arcing to ground
Hi wils tv where are you from would you be able to help fix my tv
I've taken my tv to the TV repairs like 3times in 6 months and it keeps doing the same thing its really time and money consuming and the repairers are just not doing there job properly I recon they're just making money off me
Really need help its just passing me off I spent alot of money on this TV 75 inch kdl-75w850c beautiful TV i almost wanna give up on it but your help is needed ill try this out and fix it first before I make another trip too the repairs or buy a new 9ne
Hi.josh.yeah try this fix.is very simple.just find the led err grnd and it might work.
My tv is not fixing with this action
My tv processor heats and ic cuts it's power bro i need to change my motherboard fully
ground use what
the led err wire.connect it to ground
It's been successful, friends, thank you. I present your subscribers. I am from Indonesia
@@wilstv how do i know wich cabel it is? I have a kdl40ex725
find the wire with Bl_err connections.and then connect that to any screws on your tv.
@@wilstv tuvm it worked
nice one
Hiii
Anyone want sell 65 sony lcd screen just screen?
Can hardly hear you clearly . Pls speak louder in your next video
I can hear him fine. Turn up your speakers.
Green light not coming pls somebody help
check first the main plug.connect it to different outlet.your house power may not have sufficient voltage.
My TV is green light
Only if you could have said everything louder🙄🙄
Fake player here ...cant work on my tv😶
Your voice is very slow
Barely can hear you
That's one of the poorest videos ever.
Plss tell me if the wire u cut . Have names in the connector . To connect in the board ? What line number you cut sir ?
locate the BL_Err line.then connect it to ground.
@@wilstv what is the ground???
@@wilstv do you just put it where the screw is and then just screw the screw in and it is being held down by the screw I need more clarification
Will this work on KD-75XF9005?
If it has the BL err line. If might work
Damn tested doesn't work ,TV goes on for a few seconds up to 5 min then turns off giving me 4 blinking red lights