I like its simplicity! But I am puzzled there are no pull down resistors at pin 9 & 10, these are connected to just emitters according to the manufacturer's datasheet, so the gates could never return to zero. But your idea worked anyway...
Good video! Can I put 4 different mosfets, or do they all have to be the same? I have 2 of the same and 2 more that are less volts and less Amperes. Thank you for your reply.
Hi what are you connecting everything with? Is that copper wire and solder? I’m doing this as a project for college, could you also tell me what every component does in this circuit if possible! Thanks
yapılan her iş güzeldir.Fakat burada iki sorun var.Soru 1 .Videonun tanıtımında 3000 w.yazmak ahlaki bir problem ,bunu çözmeyi düşünürmüsünüz.soru 2...açıklamalar kısmında devrenin gücünü 500-800 w.malzeme listesinde ise 12v.10a.transformatör yazmışsınız. 120 w transformatör den bu gücü nasıl almayı düşünüyorsunuz.
Hello! An important question: I have a transformer that I took out of the ups. He was in Ups and there were two batteries 12 V and connected in series together 24V. This means that it draws 24 V current. When I connected it to 220V, it gives 12V power directly. My question is. Can I make a 12-0-12 out of it to make an inverter? Thanks for the reply.
nice video please I have some questions to ask how many watts is the resistor. I'm pleased if I did not see this type of transformer what kind of transformer can I concerning the battery how did you manage to put it together sir please reply thank you.
!!! If ZVS has ferrite core in wire coil, with switch on, isn't the power draw very high without load attached to secondary of ferrite transformer? Idling mode-- waiting for the end load. A standard type switching inverter with transformer has idling mode, low power, waiting for the end load applied. People keep turning on + off power to their ZVS set up.///...???
I used 12v 2A battery and it was fine but when i increased the source to 12v 2.6A and tried to check the frequency, the tl494 ic burnt🙂 i tried twice thinking maybe the connection had some fault but i burnt 2 ICs at the end... And suggestions please?
SIR can i use 12 volt 14 amp battery.and sir which is maximum power generate in 12 0 12 5 amp transformer.and sir can i use above 2200 uf 60volt capacitor.and sir can i use equivalent ic please reply me sir.
Yo necesito lo mismo pero en 220v y de alta frecuencia, de 50Khz o similarde salida. Conoce algún módulo barato en venta para esto, por ejemplo el Aliexpress o Amazón, o dense sea no lo encuentro fácil
th-cam.com/video/4UhnSUsN3oA/w-d-xo.html
👍 work
This inverter sine wave or square wave?
@@cheerbai44 Square
Impresionante, uno de los videos más bonitos que he seguido en TH-cam
Gracias, señor.
welcome
Amazing work 👍
thanks
Good job 😎 & nice vedio 💫💥
Welcome ❤️❤️
Hasil yang luar biasa👍
welcome
I like its simplicity! But I am puzzled there are no pull down resistors at pin 9 & 10, these are connected to just emitters according to the manufacturer's datasheet, so the gates could never return to zero. But your idea worked anyway...
yes you are correct.. bro.
Good video!
Can I put 4 different mosfets, or do they all have to be the same? I have 2 of the same and 2 more that are less volts and less Amperes. Thank you for your reply.
All are same
Very nice👏👍
welcome
Hi what are you connecting everything with? Is that copper wire and solder? I’m doing this as a project for college, could you also tell me what every component does in this circuit if possible! Thanks
Yes, its are copper wire. Plz componet detials have in youtube and google.
What type of wire is getting used at 1:06 ?
Good job!
thank you
yapılan her iş güzeldir.Fakat burada iki sorun var.Soru 1 .Videonun tanıtımında 3000 w.yazmak ahlaki bir problem ,bunu çözmeyi düşünürmüsünüz.soru 2...açıklamalar kısmında devrenin gücünü 500-800 w.malzeme listesinde ise 12v.10a.transformatör yazmışsınız. 120 w transformatör den bu gücü nasıl almayı düşünüyorsunuz.
Hello!
An important question:
I have a transformer that I took out of the ups. He was in Ups and there were two batteries 12 V and connected in series together 24V. This means that it draws 24 V current. When I connected it to 220V, it gives 12V power directly.
My question is. Can I make a 12-0-12 out of it to make an inverter? Thanks for the reply.
yes 12 0 12 ok
Workinh 100%❤
welcome
Very simple thanks !!!!
welcome
Okay, can i use IC 4047 with the same construction?
This is CD4047 Inverter. th-cam.com/video/GoAPeqcZU5M/w-d-xo.htmlsi=v98QIZy6bgW8t0jB
This transformer is step down one?and can we use it for delicate items like tv , laptop? please reply 🙏.BTW nice video i will try to make it 😄.
Yes step down. Yes you can use TV, laptop
And what power output for it? And your battery power ?
Please sir, the voltage reduced when I put load. What do I do?
one Mosfet is short
Hi sir did you bend it did it work upload did you upload it
Transformers out is 120v and mosfet is heat super fast without load can you help pls
Good video. 100K preset, how many watts preset? greetings
It is normal preset
Can i use selling fan . What is watt rating for this inverter❤ 💯
500W , don't use for motors
Sir can i use 220ohm resistor on G pin of mosfet. And can i use 1000uf 35v capacitor on input of 12v. And does this circuit actually work
yes no problem
Nice
thank you
Be blessed bro, excellent tutor
are both ic TL494 and KA700 has same pinout and can i replace KA7500 in the place of TL494
Yes you can use KA7500 👌
Good I use a100Ah Battery 12v DC, on this cct
Good job. Please can i use " 35v 2200uf" ?
yes
@@homemade_101 там и на 16 в можно питпние 12 это для устойчивости монтажа применил
Hello, what about a powerful converter for big motors using a car batterie, what i do change please?
use 12v battery and use irf3205 mosfet
100percent working
Can this circuitry be designed for a breadboard ? Or using Arduino components
Don't use bresdboard because high amper controller
Is it possible to use irf540n and along with the explanation too
yes
ممتاز و من الافضل توضيح القدره الكهربيه للدائره
thank you
If you replace the transformer with another type of ferrite, how much frequency will it need?
66kHz
Please sir, can i use it to charge my phone, and laptop, and how can it last
If we put input 220 does it give us 12 DC output ?
no 12v input. out 220v
Can I run with this fan or drill machine
Yes. You can use fan
@@homemade_101 please reply me can I use 12-0-12 volt transformer
can i use 2 pcs 220 ohm resisters connected in paralal
220 ohm x2 paralal = 110 ohm same 100ohm no problem
Very good
Welcome..
I made this inverter many thanks but please tell me how it possible 100Watts transformer can support 800Watts loads?
I think cand but try
Can i use this circuit to power like TV and any other small Electronics gadgets at home?
don't use electric motors, fan
@@homemade_101 okay, what about to charge laptop and phone?
Kindly tell, Is this sine wave ??
no bro square
What resistor is use for P55N mosfet
100 ohme ok
Where can I get the 12v supply from and where can I also get that transformer from? Would you be able to link the website?
battery
عمل راقي جدا أحسنت استاذ
شكرا لك
You did this well. How many watts is the inverter?
thanks 500W
Thanks
Thanks
To make 3000W, what should be changed here? Mosfet, or something else?
bro how much load will connect in this circuit
And can i use it to charge my phones and laptop
yes but not recommended
nice video please I have some questions to ask how many watts is the resistor. I'm pleased if I did not see this type of transformer what kind of transformer can I concerning the battery how did you manage to put it together sir please reply thank you.
all resistors are 1/4W, 12V 10A battery, 5A transformer
So bro how do you manage to make 3000W with 120W power input...or it is not 3kW output? Please answer me 🙏
He said it's 500 W output @@shoaepanetheko5839
Amigo de cuántos Watts es ese inversor
yep
can we use about 5 transistor
can't 5, 5 ok total 10
I mean 6. 3 and 3. And I have 10A 12-0-12 will work fine
Sir, Can i use irf3205 mosfet? And is it pure sine wave?
yes, you can use irf3205. no this is not sine wave
Hi , Can i use 13007 and add more in paralel ?????
13007 is transistor bro. irfz44n is mosfet
شكرا على الرد ، عزيزي هل يمكن إستعمال 13007 بدل irfz44n . شكرا
Can I use ferrite core transformer
Can't bro..
What about the IC 4047...
only tl494
Sir, must the cap be 470nf
yes sorry
!!! If ZVS has ferrite core in wire coil, with switch on, isn't the power draw very high without load attached to secondary of ferrite transformer? Idling mode-- waiting for the end load. A standard type switching inverter with transformer has idling mode, low power, waiting for the end load applied. People keep turning on + off power to their ZVS set up.///...???
Please, the out is 220v, 5ohrz?
yes. it is you can changing
@@homemade_101 thank you
Can i use 55AH battery? or more? 100Ah
yes it
@@homemade_101 🙏🙏🌹🌹
I used 12v 2A battery and it was fine but when i increased the source to 12v 2.6A and tried to check the frequency, the tl494 ic burnt🙂 i tried twice thinking maybe the connection had some fault but i burnt 2 ICs at the end...
And suggestions please?
It cannot be. Check if it is properly connected. This is a good circuit.
@@homemade_101 i cross checked everything but it still burnt
Same here
@@navin1986 try adding a 1A diode on the positive input of the ic
Can I use irf3205 and add more in paralel?
can broo..
Please sir, can this work with 12 0 12 1000ma transformer
no
I used tranformer with ferite , the out put AC current cannot read in tester , what the problem Sir.
use normal transformer 12 0 12V, 5A
If you use ferrite core transformer then you have to increase the pwm frequency and set it at 66kHz.
Funcionaria la parte de potencia a 48V dc?
12V DC
Square wave or sine wave, please check the capacity of the electrical circuit
sorry Square wave
👍👍👍👍👏👏👏
One dude:
The output of 220v AC in of high frecuency? En khz? Or only down 56/60hz of red
Thanks?
50HZ
which value of resistor can suitable for IRF640N mosfet in its gate pin?
100 ohms
Hey bro. Can i use 2 mosfet
Ok but low power.. 200w
@@homemade_101 thanka 😊
Real video 😅
Excellent video and like it.👌
Welcome bro..
Thanks. video quality. I want to ask. what is the consumption of the converter in amperes without load
Without load 100ma 🤔🤔. Lode amper 5A
@@homemade_101 please help. I have a current of 2.4 amperes without load. what could be the reason. Thanks
@@Andrey-ym8di I think the Mosfets shots. Check them out.
@@homemade_101 ok/////
Hi.can u tell how many watts can it use
800W max
Please how do i connect an UPS transformer to this circuit?
This is ups transformer but. Modified: th-cam.com/video/NrFI8csluyY/w-d-xo.htmlsi=z5ljUJL2ETanTBI7
@@homemade_101 can I power my Electronics gadgets on it
what is the battery pack circuitry?
BMS. It is 3.7v battery pack
can i use 4.7 uf cap and 10k preset
@@MD_Areeb Where are you trying to use the 4.7 uF capacitor? Let me know. I think I can help you!
@@ibtidaahmed9684 thanks for your replay. I wanted to use in 0:43
@@MD_Areeb You can use it. However, it would be better if you could manage even smaller uF ones.
@@ibtidaahmed9684 ok. Thanks
Homemade 101 hola , muchas gracias por la enseñanza , que motor podria conectar ? suscriptor nuevo , gracias y likes
Como no son ondas puras, no son aptas para su uso en ningún motor.
Y la salida es en alta frecuencia?, Por ejemplo del orden de los 50khz?,
Can i use 3 amp transformer
yes, but low power out.
@@homemade_101 how many watts ?
SIR can i use 12 volt 14 amp battery.and sir which is maximum power generate in 12 0 12 5 amp transformer.and sir can i use above 2200 uf 60volt capacitor.and sir can i use equivalent ic please reply me sir.
ok no problem
what is the ampere of the transformer
10A or 5A
Yo necesito lo mismo pero en 220v y de alta frecuencia, de 50Khz o similarde salida.
Conoce algún módulo barato en venta para esto, por ejemplo el Aliexpress o Amazón, o dense sea no lo encuentro fácil
are you need high frequency out inverter ?
@@homemade_101si eso es
Necesito alta frecuancia y si es regulable con potenciometro la salida mejor
Thanks
Welcome..✌️
Sir I need high frequency MOSFET for inverter
Please tell me that's name?
Irf3205 , irfp250n
Thanks
Well done 👍 Respactabile Sir I appreciate for you Frome Pakistan Clifton Gizri Karachi Muhammad Khalid khan Thanks a lot,s Respactabile Sir
welcome @user-wl4px6ht7b
What is the output power
500W
👍👍👍
How to make it 1500watts sir,can you pls teach plssss
Not possible
Transformer w how much
100W
2k
The question is why did the feedback not work so that the scheme would be correct?
this is basic inverter
Hello can you make this 50hz to tl494ic 36khz
yes, you can.
Hola para que sea onda pura??
yes
Sir transformer kitne ampere ka hai aur is ki price kya hai ye coper hai ki almunium
5A .
Sir I made this , but I don't use potentiometer, so MOSFET died , because High frequency, I know 90hz of tl494
It frequency MOSFET not support
you are need set preset 50-60hz
Yes you are right 👍
Sir make video on Automatic Changeover using relay
Where are you from ?
sri lanka
How many watts?
200W
This is 100% working? Please true to say
yes. 100% SUER
I am trying to make but my ic was explode
it is impossible
where is the schematic
have in description box
If you replace the transformer with another type of ferrite, how much frequency will it need?
500Hz
@@homemade_101 50 Hz
Transformer w how much
200W