did you happen to see and fix your issue? I have a q7 with a camera that stopped working. Is your screen blank when you put it into reverse or did it stay on mmi radio screen when camera wasnt working>?
Thanks a lot for sharing the troubleshooting video. It’s the same issue happened with my backup camera as well. The trunk spring snapped the camera harness. I fixed it and working fine
this is most likely my problem as well..ive been having connectivity issues with my camera for months and it finally stop showing on my display. thx for sharing
Hello, first of all thank you for your detailed video! I have this problem on my Audi A4 B8. The image started cutting out intermittently and sometimes saturating like a as if a wire was moving or being cut. Please where was your black wire cut? Did you have to remove all the tape around the wires to remove all the black wire that goes from the module to the rear camera? Thank you for your valuable response!!!
Thanks heaps for this video. My issue is there is no video when I reverse. Unfortunately so far mine doesn’t seem to be a broken cable…. I’ve tested the reverse 5A fuse = 12V . Test the plug you said should be 6.5V. = 0V I have continuity between that 6.5V plug at the camera and the wiring running to the reverse module so I know the 12v wiring is good in that section. Should I just buy a working module and hope that’s my issue?
I have the same problem. I tried hooking up a battery connector I had that takes 4 AA batteries - 6v - probably close enough - and no image at the dash. I doubt the camera pulls more power than 4 AAs could supply for a while (new akaline). Might check the local pick u part boneyards. Sigh. I also have a cabriolet, and did the F202 sensor, and then the F171 went out. I am not impressed with older german electrics....
@@steamboat75043 have you scanned for codes? I’ve found the display for the parking assistant only intermittently comes on aswell. Makes me think it’s an MMI issue, though I did remove the camera module and took a look inside, there was a little bit of corrosion on the lower part of the pcb
@@Notanuffy I had pulled out the frame holding the modules on my 2010 s5 cabriolet but I was primarily concerned with the wiring for the roof module - all of which was ok - that needs the F171 sensor - which is on its way. I have a VCDS and this is what comes back (2/16/24) which is why I started checking through the wiring to find what you found. My parking assistant beeping has always worked. The guidelines show up and move with the steering wheel on the screen. When the camera did work sometimes it was slow to change back to the regular display once the car was moving forward. Still, no power at the camera so...: Address 19: CAN Gateway (J533) Labels:. 8T0-907-468.clb Part No SW: 8T0 907 468 T HW: 8T0 907 468 K Component: GW-BEM 4CAN-M H09 0101 Revision: EB700052 Serial number: 5200E0960602CF Coding: 00C303 Shop #: WSC 02391 823 56573 VCID: 52FD6823B4E19B3AC97-8006 Subsystem 1 - Part No SW: 8K0 915 181 E HW: 8K0 915 181 E Component: J367-BDM H06 0160 Serial number: 19081228040609 2 Faults Found: 02873 - Control Module for Back-Up Camera (J772) 004 - No Signal/Communication Freeze Frame: Fault Status: 01100100 Fault Priority: 2 Fault Frequency: 1 Reset counter: 226 Mileage: 136100 km Time Indication: 0 Date: 2009.04.29 Time: 00:40:49 Freeze Frame: Bin. Bits: 10111 Voltage: 11.40 V Count: 6 Bin. Bits: 10011 Time: 25.40 s 03041 - Energy Management Active 000 - - - Intermittent Freeze Frame: Fault Status: 00100000 Fault Priority: 7 Fault Frequency: 1 Reset counter: 14 Mileage: 136145 km Time Indication: 0 Date: 2009.05.16 Time: 03:45:35 Freeze Frame: Bin. Bits: 10000 Voltage: 11.30 V Count: 11
SIR. SIR. You saved me a weekend of troubleshooting!
My Q7 broke in the exact same manner.
did you happen to see and fix your issue? I have a q7 with a camera that stopped working. Is your screen blank when you put it into reverse or did it stay on mmi radio screen when camera wasnt working>?
@@ji99lypu44mines a black screen I will take a look tonight once I can find my Allen keys
Thanks a lot for sharing the troubleshooting video. It’s the same issue happened with my backup camera as well. The trunk spring snapped the camera harness. I fixed it and working fine
Boutique to check mine now! Great video keep em coming‼️💯
I have a q5 b8.5, the back up camera shows a black screen. Scan says open circuit…..could it be the same problem as yours?
this is most likely my problem as well..ive been having connectivity issues with my camera for months and it finally stop showing on my display. thx for sharing
My camera and latch dont work. The latch was initially not operable but the camera worked till last year. Thoughts?
Hello, first of all thank you for your detailed video! I have this problem on my Audi A4 B8. The image started cutting out intermittently and sometimes saturating like a as if a wire was moving or being cut. Please where was your black wire cut? Did you have to remove all the tape around the wires to remove all the black wire that goes from the module to the rear camera? Thank you for your valuable response!!!
Hallo What’s the type of the cable an from where do you bought it?
Thanks !
Thanks heaps for this video.
My issue is there is no video when I reverse.
Unfortunately so far mine doesn’t seem to be a broken cable….
I’ve tested the reverse 5A fuse = 12V .
Test the plug you said should be 6.5V. = 0V
I have continuity between that 6.5V plug at the camera and the wiring running to the reverse module so I know the 12v wiring is good in that section.
Should I just buy a working module and hope that’s my issue?
I have the same problem. I tried hooking up a battery connector I had that takes 4 AA batteries - 6v - probably close enough - and no image at the dash. I doubt the camera pulls more power than 4 AAs could supply for a while (new akaline). Might check the local pick u part boneyards. Sigh. I also have a cabriolet, and did the F202 sensor, and then the F171 went out. I am not impressed with older german electrics....
@@steamboat75043 have you scanned for codes? I’ve found the display for the parking assistant only intermittently comes on aswell. Makes me think it’s an MMI issue, though I did remove the camera module and took a look inside, there was a little bit of corrosion on the lower part of the pcb
@@Notanuffy I had pulled out the frame holding the modules on my 2010 s5 cabriolet but I was primarily concerned with the wiring for the roof module - all of which was ok - that needs the F171 sensor - which is on its way. I have a VCDS and this is what comes back (2/16/24) which is why I started checking through the wiring to find what you found. My parking assistant beeping has always worked. The guidelines show up and move with the steering wheel on the screen. When the camera did work sometimes it was slow to change back to the regular display once the car was moving forward. Still, no power at the camera so...: Address 19: CAN Gateway (J533) Labels:. 8T0-907-468.clb
Part No SW: 8T0 907 468 T HW: 8T0 907 468 K
Component: GW-BEM 4CAN-M H09 0101
Revision: EB700052 Serial number: 5200E0960602CF
Coding: 00C303
Shop #: WSC 02391 823 56573
VCID: 52FD6823B4E19B3AC97-8006
Subsystem 1 - Part No SW: 8K0 915 181 E HW: 8K0 915 181 E
Component: J367-BDM H06 0160
Serial number: 19081228040609
2 Faults Found:
02873 - Control Module for Back-Up Camera (J772)
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 226
Mileage: 136100 km
Time Indication: 0
Date: 2009.04.29
Time: 00:40:49
Freeze Frame:
Bin. Bits: 10111
Voltage: 11.40 V
Count: 6
Bin. Bits: 10011
Time: 25.40 s
03041 - Energy Management Active
000 - - - Intermittent
Freeze Frame:
Fault Status: 00100000
Fault Priority: 7
Fault Frequency: 1
Reset counter: 14
Mileage: 136145 km
Time Indication: 0
Date: 2009.05.16
Time: 03:45:35
Freeze Frame:
Bin. Bits: 10000
Voltage: 11.30 V
Count: 11
Hi my savor!! Can you tell me how this cable called to search it in eBay? Thanks in advance!!
Did you have reverse lights when your camera was out?
Where did you connect the wire?
reconnected the cut wire to the other end of the cut wire LOL
I have the same problem, I can’t figure out
I would start with each individual part it could be...I had the benefit of another B8.5 to swap parts from to see...
Common problem I assume, as I got my 2016 s4 with the reverse camera not working smh
Sir audi a3 back camra install
Dude, I did too much. You could’ve just replaced the module and voila.😊