Hello Igor, Hmmm that would have of been a good break down to work on. That was great sending the video I really do appreciate that. If you still do have the servo pack, you could use a Scopemeter to view the encoder output on the CN1 connector via breakout board. I am suspecting an issue with the servo pack encoder board. But this can also happen when you attempt to run the servo at to high of a frequency I had that problem on a 50w motor on my trainer at home. But obviously this was not the case in the test run. Hope to hear from you again :) Have A Wonderful Day Tom
Hi Tom. Encoder work fine.... actually I think that problem is one of mofset in die. This motor with new one and same config work perfectly as expected.
Igor In your video it looks as if you have the Green wire with yellow stripe connected to the W terminal output to the motor, but it also looks like the cable is spliced. Here you could have the wires between phases improperly connected. If this is indeed the case when you pressed the Servo On button you turned on the power section of the servo pack, without the run signal from the Forward or Reverse the Servo Pack attempts to hold the motor in place as if it had a load attached. Hope This Helps Tom
Thanks Tom. it's not my first yaskawa servopack. video was recorded for deller on ebay. I got new one :) I understand what You mean about cables...but sequence and all setings ok...work fine on other servopack. Thanks
hello, everyone here hi Igor this zzz sound is an issue in the power drive pack inside the servo pack must check up on your motor or test it on another drive, also i am having an issue code 030 it turns out to be a firmware issue and i must replace the drive, any ideas please help?
it's not my first yaskawa servopack...video was recorded for deller on ebay. I got new one :) which work perfect. Those one from video became a donor of spareparts.
Actually I make this video for supplyet to describe problev. Supplyer resend me new one. I believe thet is a hardware problem with mofset (power amplifier). Good luck
![⭐ฮิตในTikTok!! ( หมูเด้ง MooDeng ) Ver. แดนซ์โจ๊ะๆ ReMix BY [ ดีเจกิต รีมิกซ์ ]](http://i.ytimg.com/vi/3krsyfWUeHU/mqdefault.jpg)
Hello Igor,
Hmmm that would have of been a good break down to work on. That was great sending the video I really do appreciate that.
If you still do have the servo pack, you could use a Scopemeter to view the encoder output on the CN1 connector via breakout board. I am suspecting an issue with the servo pack encoder board.
But this can also happen when you attempt to run the servo at to high of a frequency I had that problem on a 50w motor on my trainer at home. But obviously this was not the case in the test run.
Hope to hear from you again :)
Have A Wonderful Day
Tom
Hi Tom. Encoder work fine.... actually I think that problem is one of mofset in die. This motor with new one and same config work perfectly as expected.
Igor
In your video it looks as if you have the Green wire with yellow stripe connected to the W terminal output to the motor, but it also looks like the cable is spliced. Here you could have the wires between phases improperly connected.
If this is indeed the case when you pressed the Servo On button you turned on the power section of the servo pack, without the run signal from the Forward or Reverse the Servo Pack attempts to hold the motor in place as if it had a load attached.
Hope This Helps
Tom
Thanks Tom. it's not my first yaskawa servopack. video was recorded for deller on ebay. I got new one :) I understand what You mean about cables...but sequence and all setings ok...work fine on other servopack. Thanks
hellow brow, I have the Yaskawa servopack SGDV-200A01A, it seems to show the 030 error code, do you know how to fix it?
hello, everyone here hi Igor this zzz sound is an issue in the power drive pack inside the servo pack must check up on your motor or test it on another drive, also i am having an issue code 030 it turns out to be a firmware issue and i must replace the drive, any ideas please help?
How can i run this servopac inverter to the keypad??
hi, not sure that I get quection.... to control servopac You have to connet it with USB cable to PC and run Yaskawa SigmaWIN.
Tour for Work
See the link below, link is for Sigma ll but essentially the same,
th-cam.com/video/At3DpkhKx4w/w-d-xo.html
i have a problem with servopack , the display shows PN how to solve it?
Did you solved this problem?
yes... this video was recorded for deller on ebay. I got new one :)
Break ON?
it's not my first yaskawa servopack...video was recorded for deller on ebay. I got new one :) which work perfect. Those one from video became a donor of spareparts.
Dear Mr.Igor, please how to solve this Problem, i have same problem, thank .
Actually I make this video for supplyet to describe problev. Supplyer resend me new one. I believe thet is a hardware problem with mofset (power amplifier). Good luck
please wiring sign and pulse to breakout board
Error of A.30 get by solution
I have yaskawa servo pack problem error 910 or 710 is coming