Noticed something interesting that wasn't included in the description for the boards I ordered. Found this after checking other seller's listings. These boards have an internally shorted VIN and OUT+. OUT- is switched so if you have a common ground, the OUT/LOAD will always be on. If you are trying to use this to delay a vehicle backup camera shutoff like I am, it doesn't work because all ground connections are common. In other words, the backup camera will always be on no matter what.
Hi I have a question please does the ground for the out/load - have to be different to the ground for the ground 12V ? (Both the ground on the left of the board
@@soarerloverify so if I use same ground for input 2 & 4 on the right of the board the circuit would still function correctly and switch power on and off after OP set time
@@soarerloverify P1.1: signal is triggered again, invalid Currently I have my input signal which is 12v and stays on until it loses power from another switched relay. On the right of the board I have 12v permanent and ground (which shared with my load ground) then my output + to my unit/load which is already grounded separate. Would this set up work on mode p1.1 to trigger power for 10 seconds to my unit/load then go off and not provide power again to my unit/load on output + until the signal trigger is lost and re triggered please Thank you for your reply really appreciate it 🙏
@@sarooprinceany amount of time you want just need to set it up in setup mode. Double check the wirings setup shown on the video wrong wirings can damage the unit.
You would need two boards to control two lights trigger only tell the board to active power to output but you can have multiple lights from trogger depending on your power source and just have individual on/off switch for each lights
![[4K] TREASURE(트레저) “KING KONG” Band LIVE Concert 킹콩은 라이브를 찢어🦍 [it’s KPOP LIVE 잇츠라이브]](http://i.ytimg.com/vi/p8bLLOxPDD8/mqdefault.jpg)
You have saved me from having a breakdown over this timer, THANK YOU!
Very usefull thank you very much! 👍👌🏻
Thanks you so much!
thank you
Noticed something interesting that wasn't included in the description for the boards I ordered. Found this after checking other seller's listings. These boards have an internally shorted VIN and OUT+. OUT- is switched so if you have a common ground, the OUT/LOAD will always be on. If you are trying to use this to delay a vehicle backup camera shutoff like I am, it doesn't work because all ground connections are common. In other words, the backup camera will always be on no matter what.
Teria como fazer instalando um motor de chocadeira ?
Hi I have a question please does the ground for the out/load - have to be different to the ground for the ground 12V ? (Both the ground on the left of the board
No, Same
@@soarerloverify so if I use same ground for input 2 & 4 on the right of the board the circuit would still function correctly and switch power on and off after OP set time
@@sarooprince which mode are you using on the control board. Some modes needs to be triggered in order to active
@@soarerloverify
P1.1: signal is triggered again, invalid
Currently I have my input signal which is 12v and stays on until it loses power from another switched relay.
On the right of the board I have 12v permanent and ground (which shared with my load ground) then my output + to my unit/load which is already grounded separate.
Would this set up work on mode p1.1 to trigger power for 10 seconds to my unit/load then go off and not provide power again to my unit/load on output + until the signal trigger is lost and re triggered please
Thank you for your reply really appreciate it 🙏
@@sarooprinceany amount of time you want just need to set it up in setup mode. Double check the wirings setup shown on the video wrong wirings can damage the unit.
Hi is there a way to control two lights with two different triggers ? If not do you know of a timer relay that could ?
You would need two boards to control two lights trigger only tell the board to active power to output but you can have multiple lights from trogger depending on your power source and just have individual on/off switch for each lights
Im confused what is the purpose of this unit if you have to seat there and trigger it can it cycle automatically?
Yes, trigger can done by a switch or a sensor.
Can I use this to control when my 12V motor turns on?
Yes, which mode are you plan on using?
untuk kipas angin bisa ga
सर इसके ऊपर का body या कवर या कैबिनेट कहा मिलेगा
I was getting some where.. then I got lost at triggering it with red wire. Maybe they don't do what I have in mind.
Depending on the mode you are in as some mode doesn't required a trigger to be activated. What mode are you using?
@@soarerloverify i figured it out thanks. Kept messing with it till I did
hello can you help me with my project i just want to get an advice from you, as an expert in arduino?
Hi, What do you need done or help with?
What if you trigger it first and later trigger it again while the timer is counting down.
it would it reset or do nothing Depending on which mode you're in.