Video was very helpful to be sure the procedure to remove and replace the carb properly including installing the governor linkage and gaskets. You can use the male part of the plastic choke to plug the fuel line while working on the carb. In my case the fuel tank needed to be replaced due to hard varnish and rust.
I put a new Honda OEM carb on my gx 200. It would start but not stay running. I watched your video and the manifold gasket, I put on backwards. Hole twords the valve cover. I reversed it and it runs like a scalded ass cat. You saved the day. Thanks 😊
EXactely the video i was looking for . My snow blower / Tao Tao has a clone of this motor , every parts are identical. I had problem to start for years , today i dismount and find the rust was installed in the carb due to rusty thank inside . Thanks a lot for the sharp images , you rock.
Great explanation. I just installed carburetor at my Honda power washer GX 200 6.5 following your instructions. It was very helpful. I have to get a gas and will tell you how it goes. Thanks, Jasbir Mongia
I took the gas tank completely off. There was a cheap wire hose clamp that I just twisted off with a pair of pliers because I'm replacing it with a better hose clamp anyway and the damn thing actually sparked when I broke it off. Nothing ignited but damn.
my GX motor is on a power washer. i have replaced the carb, air filter, oil and pull starter. however my motor still runs like crap, it runs with zero confidence, it randomly will shut down when I move it, or even while washing, the sound coming from the motor is not sustained like in your video when you give it full throttle. Mine only sounds and runs like that when i pin the trigger on my power washer wand. Im being told its the carb however I dont even know anymore. im seeing this thing going on sale on FB market and ebay for $400 so i know its worth throwing money into, I just dont know where im diagnosing incorrectly
You know the air box will still go on and off if you fully close the choke and turn off the gas right? And also you can reuse the gaskets if they aren’t ripped to shreds.
I installed a new chinese carburator , it started first pull . Strangely this carb has no primer input. I found this : '' the carburetor relies on a different mechanism to draw fuel into the system. In this case, the carburetor is designed with a purge bulb or venturi purge instead of a traditional primer bulb.''
Definitely was helpful video as someone who doesn't know anything about small engine or any engine for that matter. Definitely was good video. I myself thought About using a wood pallet sometime goof around and turn one into a go kart basically making a wooden go kart.
😂 tells everyone first thing you want to do is drain the gas, yet literally holds his finger over the gas line for the entire swap 🤷♂️ 🤦do as I say not as I do? That engine is a keeper , cleans off a saw table work bench real good! 👍😆 … ✌️🤙
You can use the choke lever to plug the gas line.
Video was very helpful to be sure the procedure to remove and replace the carb properly including installing the governor linkage and gaskets. You can use the male part of the plastic choke to plug the fuel line while working on the carb. In my case the fuel tank needed to be replaced due to hard varnish and rust.
thank you! someone just gave me one of these pressure washers. trying to start a side hustle. hopefully this gets it working again.
I put a new Honda OEM carb on my gx 200. It would start but not stay running. I watched your video and the manifold gasket, I put on backwards. Hole twords the valve cover. I reversed it and it runs like a scalded ass cat. You saved the day. Thanks 😊
Thank you very much from Brazil, my friend! This is a precious content!
EXactely the video i was looking for . My snow blower / Tao Tao has a clone of this motor , every parts are identical. I had problem to start for years , today i dismount and find the rust was installed in the carb due to rusty thank inside . Thanks a lot for the sharp images , you rock.
There is a niple on the choke lever and it will fit in the fuel line
So do the Honda GX200 and GX160 have the exact same carburator?
Great explanation. I just installed carburetor at my Honda power washer GX 200 6.5 following your instructions. It was very helpful. I have to get a gas and will tell you how it goes. Thanks,
Jasbir Mongia
I took the gas tank completely off. There was a cheap wire hose clamp that I just twisted off with a pair of pliers because I'm replacing it with a better hose clamp anyway and the damn thing actually sparked when I broke it off. Nothing ignited but damn.
Can you show me how to build my own racing mower
Thanks for the video
Currently trying to get an old pump to run with a 120 engine attached that my neighbour was just going to throw away
my GX motor is on a power washer. i have replaced the carb, air filter, oil and pull starter. however my motor still runs like crap, it runs with zero confidence, it randomly will shut down when I move it, or even while washing, the sound coming from the motor is not sustained like in your video when you give it full throttle. Mine only sounds and runs like that when i pin the trigger on my power washer wand. Im being told its the carb however I dont even know anymore. im seeing this thing going on sale on FB market and ebay for $400 so i know its worth throwing money into, I just dont know where im diagnosing incorrectly
I installed the carb, but if I open the choke at all it revs up a ton. What am I doing wrong?
You know the air box will still go on and off if you fully close the choke and turn off the gas right? And also you can reuse the gaskets if they aren’t ripped to shreds.
wow thanks for that time saving tip...
If you use the choke lever round rod to plug the gas
Just did this on a 140. I ordered a carb from Honda and replaced everything around it.
Golf ball tee to plug the fuel line. Great video, Thanks !
I installed a new chinese carburator , it started first pull . Strangely this carb has no primer input. I found this : '' the carburetor relies on a different mechanism to draw fuel into the system. In this case, the carburetor is designed with a purge bulb or venturi purge instead of a traditional primer bulb.''
Super helpful, thanks for doing this!
Definitely was helpful video as someone who doesn't know anything about small engine or any engine for that matter. Definitely was good video. I myself thought About using a wood pallet sometime goof around and turn one into a go kart basically making a wooden go kart.
Thanks for sharing that. It's a detailed and helpful video with helpful tips.
Great presentation. Thank you sir!!
You forgot 1 thing, you did not put the hoseclamp back on the fuel hose.
Thanks for this helpful video. 🙏👍
Super helpful video. Appreciate it.
😂 tells everyone first thing you want to do is drain the gas, yet literally holds his finger over the gas line for the entire swap 🤷♂️ 🤦do as I say not as I do? That engine is a keeper , cleans off a saw table work bench real good! 👍😆 … ✌️🤙
Very well done.
Great job
Clamp fuel line
That filter looks healthy, NOT!