@@mikekingtv3325 I have a great question for you, I am interested in a twist throttle that starts you off slow, because I notice that all the cheap $15 twist throttles that I a have used, knock you off the saddle as soon as you barley turn it to its minimal activation point, I am looking for a throttle that starts off very slow and gradually starts accelerating to full speed. Please refer me to one either through amazon link or a model and model number, I will subscribe to your channel upon you response. thanks
panalo ka lods. galing mo magturo. subscribe na ako. pero itatanong ko lng, kung d ka makakuha ng 4volts, o mga 3v lang nakuha mo, ibig sabhin ba nito, mahina ang signal, at babagal ang takbo ng ebike?rama ba idol
Hi, first of all, thank you for this very usefull video. I have a problem with my e-quad throttle reaction, I have 4 different throttle, one finger type and three twist type, I measured the output signal as you discribed and didn't see any major problem but the motor driver doesn't give any response during the first angles of the throttles, but after the first 4-8 degrees, the motor starts to spin with a higher speed than desired and it makes a bad feeling on driving characteristics of quad. Between the 4-8 degrees to max throttle, there isn't any problem. Because of this issue, I can't drive the quad at very slow speeds below 5kph. Do you have any suggestion to fix this issue? Thanks. I checked this issue with another motor driver as well, and the result was the same.
I have a Phantomgogo R1 36v scooter. The make and model are Sine wave brushless controller 2HM-0. When I tested the 5v red wire coming out of the controller I found that the 5 volt Red Wire is pushing 17.44 volts. I am afraid of connectiing the.controller to the throttle because I do not want to damage the throttle. Is this high voltage normal or is it a defect? Will it destroy my throttle?
The voltage is so high.. maybe you also check the supply of the hallsensor on the motor HUB if the same reading.. . Because it should be all 5volts the same on the throttle..
I have a controller. And on the controller is a jst-sm 4 pin connector for both the brakes and the throttle together. 2 are for the brakes and that leaves 2 more pins which are of course for the throttle. But, the throttle has 3 pins. Could it hurt my bike if I switch the pins around until I find which pin goes where ?
@@mikekingtv3325 in this order. Grey, white, brown and black. They told me the grey and the white were brake wires. Thanks. So you think the white might be the signal ?
hello micke i have problem in my scooter 48v 1000w evry thing is marche but the motor is not when i test the red and the black it 0 v and between the black and green also 0 v
Check input Voltage, if you have input supply voltage you should have the output reading... If not check open wire Used resistance measurements end to end or wire check if there is open line wire connection.
@@mikekingtv3325 wala na nka stock na, khit yung motor nya e 5 volts yun bkit nawala. umiilaw nman yung panel nya kpg switch ko yung ignition switch nya. tanong ko sa ebike store e sira na raw controller nya dapat bili raw ako bago o palitan yung controller. salamat boss sa reply mo.
@@mikekingtv3325 ok. And twisting the throttle will increase reading? Correct? So once I verified that where on the controller do we connect the green one too?
Sir 48 volts e bike mataas Naman Ang charge biglang tumirek. Tapos tsinek ko supply Ng throttle lumalabas 29 volts DC . Possible ba na sira na Ang controller. Please help thank you.
Ang throttle kc 5 volts lng un kabyan.. baka nga sira ang controller mo.. piro kong natakbu siya tapus natirik lng.. check mo lahat ng battery kong my blotted.. piro tataka ako bakit 29 volts ang sa throttle mo.. mas maganda niyan kabyan kong sa palagay mo i sira ang controller mo kong may trupa k jan n my stuck n controller kabit mo muna pra ma try mo bagu ka bumili.. baka kc iba ang sira sayang pagbjli k agad
sabi ni tumer d macontrol yong accelarator . tuloy tuloy takbo. pero pinuntahan ko ok naman ibig sabihin may loose sa wiring saan kaya doon first time ko mag repair ng ebike
☠️ I've been experiencing extremely dangerous episodes of the motor not stopping as soon as I turn the throttle , related to high humidity conditions ! I think it's because the humidity increases conductivity of the hall sensors in the throttle . can you recommend a good throttle ? I think the manufacturers are going to have to make them water proof. I experienced the same issue with a different throttle , battery and controller. just using the bike after a rain storm is enough to cause the issue. We must have a throttle will a switch to cut power ! ☠️ Also stop using hot glue on the Hall sensors ! It melts were I live ! And make the throttle not Fall apart so easy , and they need to be made with softer grips or made to accept normal grip's.
MCY Throttle or handle bar Switches is water proof, and some controller can be set at program on throttle so if there are not normal the controller automatic cut. So the motor can't run
@@mikekingtv3325 thanks, I've talked to a company that has seen the issue before but only in the throttles that have high battery voltage running inside to a lcd. screen
![เปิดบ้าน โคตรสวย ป๋องกพล รู้จักตั้งนาน เพิ่งรู้ว่ารวย!!! l [Nickynachat]](http://i.ytimg.com/vi/tmgCF_2HfYI/mqdefault.jpg)
An excellent way to test the throttle. keep uploading we all need help!!!
Thanks 😊
Good method ..thanks
Thank you also
Ty very clear😊
Thanks
The waterproof julet connecters are trickier , i need a spare set with bare wires one end !
Salamat ng marami.idol
Salmat
Thanks po dito sa tutorial mo sir Mike very Interesting po
😁😊😊salmat din.. God bless po..
@@mikekingtv3325 I have a great question for you, I am interested in a twist throttle that starts you off slow, because I notice that all the cheap $15 twist throttles that I a have used, knock you off the saddle as soon as you barley turn it to its minimal activation point, I am looking for a throttle that starts off very slow and gradually starts accelerating to full speed. Please refer me to one either through amazon link or a model and model number, I will subscribe to your channel upon you response. thanks
Matrabaho din pla magcheck ng throttle ng ebike chong eheh. Nice tutorial!
salmat boss..😁
panalo ka lods. galing mo magturo. subscribe na ako. pero itatanong ko lng, kung d ka makakuha ng 4volts, o mga 3v lang nakuha mo, ibig sabhin ba nito, mahina ang signal, at babagal ang takbo ng ebike?rama ba idol
Nice content boss.. more videos like this.. 😊😊😊
salmat pre
Hi, first of all, thank you for this very usefull video. I have a problem with my e-quad throttle reaction, I have 4 different throttle, one finger type and three twist type, I measured the output signal as you discribed and didn't see any major problem but the motor driver doesn't give any response during the first angles of the throttles, but after the first 4-8 degrees, the motor starts to spin with a higher speed than desired and it makes a bad feeling on driving characteristics of quad. Between the 4-8 degrees to max throttle, there isn't any problem. Because of this issue, I can't drive the quad at very slow speeds below 5kph. Do you have any suggestion to fix this issue? Thanks. I checked this issue with another motor driver as well, and the result was the same.
Maybe your hallsensor of your throttle inside not inplace. So that the magnet ang sensor can not turn in normal.
@@mikekingtv3325 anong number value code po ng hall sensor para sa throttle
I have a Phantomgogo R1 36v scooter. The make and model are Sine wave brushless controller 2HM-0. When I tested the 5v red wire coming out of the controller I found that the 5 volt Red Wire is pushing 17.44 volts. I am afraid of connectiing the.controller to the throttle because I do not want to damage the throttle. Is this high voltage normal or is it a defect? Will it destroy my throttle?
The voltage is so high.. maybe you also check the supply of the hallsensor on the motor HUB if the same reading.. . Because it should be all 5volts the same on the throttle..
nice tutorial lodz .. keep uploading ..
thanks boss ..
Master pwedi bang gamitin iyong charger n prang sa laptop n 24volts sa batter n 24volts dn, thanks and more vlogs Watching from KSA
Charger lang Ng cp boss 5 volts
I have a controller. And on the controller is a jst-sm 4 pin connector for both the brakes and the throttle together. 2 are for the brakes and that leaves 2 more pins which are of course for the throttle. But, the throttle has 3 pins. Could it hurt my bike if I switch the pins around until I find which pin goes where ?
Okay si may be the 4 wire are
Black- negative
Red- 5 volts
Green- output signal
Yellow Green - high brakes
@@mikekingtv3325 in this order. Grey, white, brown and black. They told me the grey and the white were brake wires. Thanks. So you think the white might be the signal ?
ung hall sensor na yan sir na ic same din ba ng nasa motor na hall sensor ic kung same pwd ba malaman ung part number nya
Same lng boss.. search mo boss Hallsensor.. marami bady marking yan piro same function
Good day po idol.. ask ko lang, pwede ba pang replace ang 41E Hall sensor sa trotle, 49F po kasi ung sa trotle. salamat!
Poyde boss..
😊😊😊😊😊😊😊😊😊😊💯👍
Thanks
Parehas yong number ng trotle sensor sa hub sensor
Parihas boss
Thankyou ❤️😊
Thanks
What is the function of a transistor on a Ebike
It's a hallsensor that sends a signal to the controller for idle and speed ftom, .8 volts to 4.6 volts
Master masunog ba iyong IC sensor nia kong nasupply ng 12volts
Yes boss di siya poyde mag over voltage 5 volts lang kc yon
Sir paano ba mg palit ng e bike controller na di parihas ang socket pwede ba yon ma convert
Boss ala k ba mga connector.. .. poyde mo din gamitin ung stock niyang connector
hello micke i have problem in my scooter 48v 1000w evry thing is marche but the motor is not when i test the red and the black it 0 v and between the black and green also 0 v
Check input Voltage, if you have input supply voltage you should have the output reading... If not check open wire Used resistance measurements end to end or wire check if there is open line wire connection.
sir bkit walang 5 volts yung supply ng trottle ng bike ko kya ayaw umandar. saan ko ba hahanapin yung 5 volts e 48 volts nman tong ebike ko.
Ibig sabihin boss di nag activate ang controller.. naka patay pa kaya ala 5 volts
@@mikekingtv3325
wala na nka stock na, khit yung motor nya e 5 volts yun bkit nawala. umiilaw nman yung panel nya kpg switch ko yung ignition switch nya. tanong ko sa ebike store e sira na raw controller nya dapat bili raw ako bago o palitan yung controller. salamat boss sa reply mo.
Ilng volts po ung ic sir n ipapalit...
5 volts yong hall sensor bossing..
Sir saan po ba nabibili yang transistor, pwede ba sa electronics supply.
Yap boss.. search mo ang hall sensor marami kc body no. Un piro same lang.
Salamat sir ha, sana'y dios na lang bahala sa ipinamahagi mong kaalaman o karunungan sa aming intereadong matututo.
Sir, saan ba galing yang 5 volts ng trottle, may na check ako sa converter na 12 volts, paano na reduce yung 12volts to 5 volts?
Where do you connect your green signal wire too?
I connected to positive of my test probe of my digital multimeter
@@mikekingtv3325 ok. And twisting the throttle will increase reading? Correct? So once I verified that where on the controller do we connect the green one too?
Meron po kayo how to check oem lcd if short circuit or what
Boss san po nakaka bili ng prang transistor
Sa shoppe boss
Sir ano kaya sira ng e-bike ko 73kph ang naka display sa pannel ko kahit di naman tumatakbo. Dapat sana 00 sana.
Ginalaw pa ang wirning boss. Need check bossing
Thank you, can we be frnds
Yes .. i done.. .. thanks
Sa akinYung throttle logo sa dashboard lumalabas ayaw gumana pag piniga.
Check mo bossing baka loose lang pag may tester ka ma tetest mo kong sira talaga siya sa output ng throttle kong nagana ng maayos
san po nakakabili ng hall sensor ic?
Sa mga electronics store po
Sir 48 volts e bike mataas Naman Ang charge biglang tumirek. Tapos tsinek ko supply Ng throttle lumalabas 29 volts DC . Possible ba na sira na Ang controller. Please help thank you.
Ang throttle kc 5 volts lng un kabyan.. baka nga sira ang controller mo.. piro kong natakbu siya tapus natirik lng.. check mo lahat ng battery kong my blotted.. piro tataka ako bakit 29 volts ang sa throttle mo.. mas maganda niyan kabyan kong sa palagay mo i sira ang controller mo kong may trupa k jan n my stuck n controller kabit mo muna pra ma try mo bagu ka bumili.. baka kc iba ang sira sayang pagbjli k agad
@@mikekingtv3325 ok Po sir. Salamat sa info. Check ko rin Po.
Kabayan nasa magkano kaya ang hall sensor at ilan piraso yan?
Isang pirasu lng boss nasa 30nt
Sir dyan din ba naka kabit yung, speed dun sa LCD?
Hindi boss sa controller nakakabit ang wire para dun s speedometer
Pano pag ung trottle pag hinawakan lang umaandar na sira na baun
Need check bossing
San po ba maaring makabili ng sensor
Marami sa electronics store
Bakit e bike. Ko in unang andar pabigla bigla .DIY repair trotell
pre mike nasa taiwan ka pa rin ba
Yap pre d2 padin..
San kaya siya pwedeng ipaayos? Kasi d marunong ang bikeshop
Bkit boss.anu.b prob. Ng e bike mo..
Ayaw na po gumana ang throttle niya kanina lang. Nahirapan kami maghanap ng mag-aayos. Ngayon andun asawa ko sa pagawaan ng motor
Panu po ba ng yari bigla lng ba di tumakbo kabyan pag pinihit.. baka ang sita niyan ay breakswitch lang..
boss bat kaya ung 3wheel ko pg inaabante nbgal ngvaviraite lng.sya pero.s atras ok.nman.sya.sna msagot pra may idia
Boss pano po pag 0.86 po yung green pero 4.5V lang po ang read sa red. Palyado napo ba ang controller(48V) non. ?
Yong green boss.output signal un papuntang controller , pag pinihit mo.ng sagad tataas un hanggang 4.3 volt.. kc ung red at black supply lng.un.
Sir bka po my alam kau.ask ko lng po kc ung ebike ko po pag Anu po mlakas humatak pero mayamaya po humihina bago nmn po ung battery nya
Ilang watts ba controller
pre mike si arnold to. paano magtanggal ng hall sensor
Pre ikaw pla yan.. musta...
Sang hall sensor sa hub or throttle pre.. pag sa hub babaklasin mo pre ganun din sa throttle
@@mikekingtv3325 sa throttle
Madali lng pa sa throttle pre.. baglasin mo muna
sabi ni tumer d macontrol yong accelarator . tuloy tuloy takbo. pero pinuntahan ko ok naman ibig sabihin may loose sa wiring saan kaya doon first time ko mag repair ng ebike
Check mo nlng pre ung dulo dulo ng wire tapus igalaw mo ung manubila kong my loose b talga
Throttle ki price kya hai
250nt
👍👍👍
thanks
ok
👌👍
En français
☠️ I've been experiencing extremely dangerous episodes of the motor not stopping as soon as I turn the throttle , related to high humidity conditions ! I think it's because the humidity increases conductivity of the hall sensors in the throttle . can you recommend a good throttle ? I think the manufacturers are going to have to make them water proof. I experienced the same issue with a different throttle , battery and controller. just using the bike after a rain storm is enough to cause the issue. We must have a throttle will a switch to cut power ! ☠️ Also stop using hot glue on the Hall sensors ! It melts were I live ! And make the throttle not Fall apart so easy , and they need to be made with softer grips or made to accept normal grip's.
MCY Throttle or handle bar Switches is water proof, and some controller can be set at program on throttle so if there are not normal the controller automatic cut. So the motor can't run
@@mikekingtv3325 thanks, I've talked to a company that has seen the issue before but only in the throttles that have high battery voltage running inside to a lcd. screen
Can't understand these folks 😒