*[...Jacob showing his dad card...] "hey let's blow some Mickey Mouse ears on this thing!"8 *Also a clean cut that's going to save you 25 minutes of cleanup AFTER you have the rigtht file and flapper disk found.*
You can make 1 out of a piece of 1” flat bar drill a 1/4” hole then measure whatever the radius of a circle you want then drill a hole for the drag tip to fit in. Drill a 1/4” hole in the center of the circle you want and put a bolt . It works pretty good just have to weld the hole up when your done and it’s cheap
Hypertherm makes them. They fit straight onto the torch. Edit; Because y’all have a drag tip you don’t need the outrigger wheel. You can still use the wheel if you want it’s just not necessary.
Thanks Jacob!! Definitely going to go check this out. We all appreciate all the videos you do!!! They a very educational and very informative. Be blessed sir!!
If your using the plug, start with your tip outside the cut, blow through, then without letting off of the high pressure, slide the point into the punch mark. Try to make it a smooth transition and just start your radius cut immediately after you drop in to the punch mark. What this does is make it where you don’t have a blow through hole in your part. If you’re using the hole, do the opposite. When you get used to it, you won’t even need to grind. Unless you’re going to weld on it.
This particular cutting device looks good but, I noticed that you didn’t show cutting a bigger radius, such as in the range of 8” to 12” in diameter. Little diameter like what you did there of about 5-6 dia is the maximum for this cutter device.
Thanks for the video on that circle rig! I’m gonna pick me one up. The link you put in the description doesn’t work though and I have to ask, are you growing one of those ridiculous mullets like I see every teenage boy have nowadays? Lol
I didn’t quite understand how you adjust the radius of the cut. I can see how to raise and lower the torch up or down towards the steel using the wingnut. Or does it just come with a few different pre-set sizes of that L shaped attachment Like 1” 2” 4” or something like that? Stay blessed bro EDIT: Watched the B roll and first cut again. I see how to increase or decrease the arc now
That’s gorgeous smooth ass cut!!! That’s almost like a water jet cutter!!!
holy heck!! That thing is mint!! Why have I never seen one of them before. I must run with a real cave man crowd.
holy cow, gotta get me one of those, tired of walking around the material I'm cutting especially in a smaller shop setting
If you take care of it, it will last forever
*[...Jacob showing his dad card...] "hey let's blow some Mickey Mouse ears on this thing!"8
*Also a clean cut that's going to save you 25 minutes of cleanup AFTER you have the rigtht file and flapper disk found.*
Thanks have a blessed day America
Do they make them for plasma setup? That would be sweet deal for my hypertherm
My exact thoughts
You can make 1 out of a piece of 1” flat bar drill a 1/4” hole then measure whatever the radius of a circle you want then drill a hole for the drag tip to fit in. Drill a 1/4” hole in the center of the circle you want and put a bolt . It works pretty good just have to weld the hole up when your done and it’s cheap
They will be here shortly
Hypertherm makes them. They fit straight onto the torch. Edit; Because y’all have a drag tip you don’t need the outrigger wheel. You can still use the wheel if you want it’s just not necessary.
That's a quality piece of tooling brother, gotta snatch me up one.
I think you are going to love it
Great review Jake 👍! Yeah some crazy weather, that's for sure.
Thanks Wade. Hope you are doing well.
@@JacobSchofield yeah not too bad. Stay safe out there buddy 👍
was waiting for your tarp to flare up......great little video Jacob ...cheers
Thanks Jacob!! Definitely going to go check this out. We all appreciate all the videos you do!!! They a very educational and very informative. Be blessed sir!!
Thank you Derek means the world us that you guys enjoy the videos. Be blessed
If your using the plug, start with your tip outside the cut, blow through, then without letting off of the high pressure, slide the point into the punch mark. Try to make it a smooth transition and just start your radius cut immediately after you drop in to the punch mark. What this does is make it where you don’t have a blow through hole in your part.
If you’re using the hole, do the opposite. When you get used to it, you won’t even need to grind. Unless you’re going to weld on it.
Hi Brother. Is the adaptor removable?? Thanks
That sounds like some good ole Northern Missouri weather we get.
Has it been crazy over there too? Not going to lie we thought the snow was over 😂
is it sold online?
Can I ask the name of the tool?
Good job jacob
Minty 👌. I really need to upgrade !
This thing is worth up grading to
hahaha , get you some devil dust lol . good to see you back great vid , thanks
Thanks Greg felt good to finally put out another video.
Exactly what I needed man, thank you
Glad it helped Jayden.
3:53. Gostaria de saber o valor e se vcs importavam para o Brazil
We just made them ourselves,they're actually pretty simple!
Be curious to know how long that bearing lasts
Bom dia como faço para ter um
How do i get the tool
Well, you made me buy one......
Jacob do you know the discount promo code for this?
Were in a drought in Florida,
This particular cutting device looks good but, I noticed that you didn’t show cutting a bigger radius, such as in the range of 8” to 12” in diameter. Little diameter like what you did there of about 5-6 dia is the maximum for this cutter device.
Thanks for the video on that circle rig! I’m gonna pick me one up. The link you put in the description doesn’t work though and I have to ask, are you growing one of those ridiculous mullets like I see every teenage boy have nowadays? Lol
I didn’t quite understand how you adjust the radius of the cut.
I can see how to raise and lower the torch up or down towards the steel using the wingnut.
Or does it just come with a few different pre-set sizes of that L shaped attachment
Like 1” 2” 4” or something like that?
Stay blessed bro
EDIT: Watched the B roll and first cut again. I see how to increase or decrease the arc now
I’ll do another video. This kit will cut I believe a 5/8 to 16” hole
How big does it go
I built my own circle cutter for the plasma cutter....I'm sure I could put a bushing in it and use it with oxy-acetylene
Right on.
Nice
Hows the pipeline work doing?
I haven’t been on a pipeline since last April. 😂 we where kinda forced to find other means of work which in the end was a huge blessing to us.
@@JacobSchofield you can thank Biden for that 👎💩
Sweet
Where are you located?
Western United States
Cool
Don’t force it. Get a bigger hammer. Your cuts look much like machine burned parts that I have had made. Good job!
Straight torch on the small circle works better...... 90 degrees on a flange wizard for the bigger diameter holes
Looks to me a global warming 😂 😂 😂 😂 thank you for sharing
Wish it was about a hundred dollars
👍👍👍
Get you local machinist to turn you out a bushing for that baby 👶 torch
Cory great thoughts, I think circle B technology is going to build a lot for a baby torch and a plasma set up. Should be coming out here shortly.
Very nice but to rich for this guys blood.
Good tools always cost money. But if taken care of this thing could be handed down.
Worth every penny??? How many pennies did you pay? Wtf
Lots of pennies.