We just got our 2021 212XE in the water. After 4 days of use I knew the factory buckles need to go. We put in on the northeastern end of Cayuga so it’s almost a 2hr drive. I always have to stop and tighten them down. I should have my boat buckles by Friday. I can’t wait to install. Great video thanks!
Hey Capt. Leon…When I picked up my 2021 195S two months ago, and had one of the Yamaha supplied tie down come loose on the way home from the dealer. Knew right away, they had to go. I installed similar ratcheting buckles on my trailer…what a difference! Thanks for another great video.
Remember to recheck these after you drive for a bit and the boat settles into position. They usually need another click then they are good to go!! Coming from an AR240 owner
Installed my SS boat buckles today in the exact location as yours. One of my best investments...I DID NOT add a spacer as previously suggested. The straps are free and clear (as long as the boat is on straight)
Why? At that strap angle, regardless of how much you crank that strap down it will not prevent the boat lifting off the trailer. This installation is 'Two thumbs down'. The purpose of those Boat Buckles is to pull the boat directly down 'vertically' on to the trailer.
While I agree with you Ross, on that boat trailer combo there is no way to install the straps in a vertical position. Even the OEM comparable set up has them where mine were installed. I suppose it's better than nothing, but you're right.
@@CaptainLeonsBoatingandMore Agreed I am also tired of the 'modifications', but then my wife says it keeps me out of the house! Your boat/trailer design is a problem when trying to mount those great ratchet straps correctly. Again, those straps are to pull the boat directly DOWN onto the trailer, to make the boat and trailer move as one. The angle you have those straps exerts little to zero DOWN force. Those straps are only pulling the boat forward onto the winch post. I had a similar problem and had to do yet another workshop 'modification' to my trailer. Your combo is a little more difficult, to get that down force maybe throw the strap over the top of the boat?
you're not bored...its dedication to being efficient... and you like things smooth! did you silicone by the washer, or is it a hollow tube, and salt water can drain out the bottom? If it was a tub/4 side piece I drilled into I would have silicone'd... but I know nothing and maybe the ends are open so it doesn't matter?
Why not put a spacer between the buckle and frame and the strap will be free of ant contact. Maybe one or two stainless steel washers is all. I will be mounting mine in the same location, but will add a spacer. I love your videos, comical too.
Not a bad idea Rob, although the buckle assembly won’t be as flush to the trailer frame. Let us know how it goes. Appreciate the compliment, thanks for watching!
@@CaptainLeonsBoatingandMore galvy process should apply to both surface, inside out. Looking for holes, like the one on cross beam, 5:15 min in your video.
I also must say that the factory straps on the 190 were an annoyance that I learned to tolerate over the years. Can't tell you how many times I'd come close to jamming my finger while tightening them down! 🤔
LEO just tinted my windows ! looks sharp ! you should do it and make a video .. i went with 50% but wish i did 35 % anyhow it adds class of looks and some glare protection makes inside boat feel cooler and comfortable
@@CaptainLeonsBoatingandMore whatever you do stay away from 20% and below to dark and reduces visibility when seated driving . 35 % is Perfecto and looks sharpe!
@@CaptainLeonsBoatingandMore where is the best place to launch in morichies out to GG for day parking safe and all ? ... I was looking at remsenburg 20$ for day marina but they said ramps steep in LT ? thnx
A set of these Boatbuckle straps came on my 2175 Pro-V , I broke a strap and called the company to get a replacement, they said they don't sell them and you have to just buy another set. What B,S.!!
Trevor they want the strap to pull straight off the reel and return back as straight as possible, that would be 0 degrees. Watch my video at the 7:50 mark, mine is almost at 0%. They will allow up to 30 degrees if it being pulled slightly off straight. This has nothing to do with the orientation of the mounted buckle mechanism. Hope that explains it, thanks for watching!
Chris, they are doing awesome. I'm exclusive salt water use but make an effort to wash with fresh water after every outing. No visible signs of wear or corrosion.Very pleased with them!
@@CaptainLeonsBoatingandMore Bullshit! three trips and these pieces of shit were smoked. I do a COMPLETE wash down of my boat, trailer, rods, reels all accessories EVERY TRIP, that includes soap and water, and the pressure washer. These things rusted together in no time, unoperable.
I just have to say, that this is the 4th Video that has suggested using a 7/16th Drill Bit! Like WTF guys......the Bolt is a 1/2" Bolt.....so...try as you might, That 1/2" Bolt is not going to make it, through any 7/16th Hole! I keep my boat 1/2 hour drive from our place. So....to get all the way out there, to discover that I needed a 1/2" Drill Bit.....Pissed me OFF! Yes......I should have checked the Bolt and Nut before I headed out, so that is on me. BUT......I just thought, that after watching 4 Videos on this "SIMPLE" install........that these 4 guys, knew what they were talking about? I won't make that Mistake again. Its a HALF INCH BOLT people.......Take a HALF INCH Drill Bit with you.....Just in case! DOH!
Ray, are you implying that 4 separate unconnected TH-cam creators each decided to incorrectly state the size of the drill bit they used? For real bro? I’m very careful in the free content and guidance I provide to my viewers. I’m methodical in following manufactures suggestions and guidance. I don’t know the size of the bolts your product came with, as you say that’s on you, but my bolts, my drill bit and even the instructions all said 7/16. Worked perfectly! Thanks for watching.
If you are looking at buying these things for your boat, DON'T!! I put these things on my brand new aluminum trailer to hold my boat, thinking that all f the "reviews" were good. After the VERY FIRST trip to the water, the next time out they became hard to release. I then took them off, sprayed them inside with corrosion X, lithium grease and even MAX WAX!! They made three trips to the water, after the third trip I had to cut the straps with my knife to release my boat from the trailer. I currently have two giant chunks of rusted together garbage to show for my money. DO NOT BUY, unless you like throwing your money away.
![[UNCUT] “อภิสิทธิ์” ครม.อุ๊งอิ๊ง แย่งเก้าอี้กันฝุ่นตลบ “ทักษิณ” บงการเอง Iคนดังนั่งเคลียร์I 21ส.ค.67](http://i.ytimg.com/vi/a_b-kItw2jY/mqdefault.jpg)
Great video! I never minded the old tie downs until I got the ratchet style, I wouldn't want to go back now.
Thanks for the shout out!! AH-BOOM.
We just got our 2021 212XE in the water. After 4 days of use I knew the factory buckles need to go. We put in on the northeastern end of Cayuga so it’s almost a 2hr drive. I always have to stop and tighten them down. I should have my boat buckles by Friday. I can’t wait to install. Great video thanks!
Hey Capt. Leon…When I picked up my 2021 195S two months ago, and had one of the Yamaha supplied tie down come loose on the way home from the dealer. Knew right away, they had to go. I installed similar ratcheting buckles on my trailer…what a difference! Thanks for another great video.
Thanks for watching Matt, beautiful boat you have!
The boat will shift forward if not up tight against the front roller, which will cause the OEM buckles to loosen.
@@MrRfitz3 Good point! Thanks for watching.
Remember to recheck these after you drive for a bit and the boat settles into position. They usually need another click then they are good to go!! Coming from an AR240 owner
Thanks Anthony, will do!
Awesome video Leon! Now I just have to convince my wife lol. Thanks for the shout out!
Sounds like a plan!
Excellent, I placed buckles but I like the position if where these are. Going to relocate.
i just did these lol .. they work great spray them with some fluid film so they prevent rust ...
Installed my SS boat buckles today in the exact location as yours. One of my best investments...I DID NOT add a spacer as previously suggested. The straps are free and clear (as long as the boat is on straight)
Good stuff Rob, yeah, I'm loving them thus far. I'm taking the time to hose them off good after dunking the trailer in salt water.
Capt Leon, I think you were sold on them once you saw them on the 252SE, right?
Why? At that strap angle, regardless of how much you crank that strap down it will not prevent the boat lifting off the trailer. This installation is 'Two thumbs down'. The purpose of those Boat Buckles is to pull the boat directly down 'vertically' on to the trailer.
While I agree with you Ross, on that boat trailer combo there is no way to install the straps in a vertical position. Even the OEM comparable set up has them where mine were installed. I suppose it's better than nothing, but you're right.
@@CaptainLeonsBoatingandMore Agreed I am also tired of the 'modifications', but then my wife says it keeps me out of the house! Your boat/trailer design is a problem when trying to mount those great ratchet straps correctly. Again, those straps are to pull the boat directly DOWN onto the trailer, to make the boat and trailer move as one. The angle you have those straps exerts little to zero DOWN force. Those straps are only pulling the boat forward onto the winch post. I had a similar problem and had to do yet another workshop 'modification' to my trailer. Your combo is a little more difficult, to get that down force maybe throw the strap over the top of the boat?
you're not bored...its dedication to being efficient... and you like things smooth! did you silicone by the washer, or is it a hollow tube, and salt water can drain out the bottom? If it was a tub/4 side piece I drilled into I would have silicone'd... but I know nothing and maybe the ends are open so it doesn't matter?
It all drains out, no worries!
@@CaptainLeonsBoatingandMore Thank You
Why not put a spacer between the buckle and frame and the strap will be free of ant contact. Maybe one or two stainless steel washers is all. I will be mounting mine in the same location, but will add a spacer. I love your videos, comical too.
Not a bad idea Rob, although the buckle assembly won’t be as flush to the trailer frame. Let us know how it goes. Appreciate the compliment, thanks for watching!
Great video. dont forget to coat the hole cutting surface to prevent corrosion.
Good point. Does the galvanized process they apply to the trailer only protect the outer metal surface, honestly not sure.
@@CaptainLeonsBoatingandMore galvy process should apply to both surface, inside out. Looking for holes, like the one on cross beam, 5:15 min in your video.
I also must say that the factory straps on the 190 were an annoyance that I learned to tolerate over the years. Can't tell you how many times I'd come close to jamming my finger while tightening them down! 🤔
They served their purpose, glad I moved on!
LEO just tinted my windows ! looks sharp ! you should do it and make a video .. i went with 50% but wish i did 35 % anyhow it adds class of looks and some glare protection makes inside boat feel cooler and comfortable
Good deal, we will see. I never felt the need for tint, but it does look sharp. Thanks for watching!
@@CaptainLeonsBoatingandMore whatever you do stay away from 20% and below to dark and reduces visibility when seated driving . 35 % is Perfecto and looks sharpe!
@@CaptainLeonsBoatingandMore where is the best place to launch in morichies out to GG for day parking safe and all ? ... I was looking at remsenburg 20$ for day marina but they said ramps steep in LT ? thnx
@@demolaj1 There is a Suffolk County Ramp at the foot of the Smith Point Bridge. Town of Brookhaven also has a ramp at the Forge River by permit only.
@@CaptainLeonsBoatingandMore Thanks Leo
A set of these Boatbuckle straps came on my 2175 Pro-V , I broke a strap and called the company to get a replacement, they said they don't sell them and you have to just buy another set. What B,S.!!
Not good customer service, perhaps there is a reason. Thanks.
I need to get some of those. Would it be better with the hook facing up? Just a thought.
Either way I'm sure is fine, they are great. Thanks for watching.
My boat weighs about 3500lbs. Are these strong enough for me??
Sure are. You are not lifting the full weight of your boat just holding it from moving. I think each strap has like 1800lb. holding power.
What about the no more than 30 degrees from vertical as detailed in the instructions? You look like about 70 degrees from vertical.
Trevor they want the strap to pull straight off the reel and return back as straight as possible, that would be 0 degrees. Watch my video at the 7:50 mark, mine is almost at 0%. They will allow up to 30 degrees if it being pulled slightly off straight. This has nothing to do with the orientation of the mounted buckle mechanism. Hope that explains it, thanks for watching!
how are these holding up to the elements ? any corrosion
Chris, they are doing awesome. I'm exclusive salt water use but make an effort to wash with fresh water after every outing. No visible signs of wear or corrosion.Very pleased with them!
@@CaptainLeonsBoatingandMore Bullshit! three trips and these pieces of shit were smoked. I do a COMPLETE wash down of my boat, trailer, rods, reels all accessories EVERY TRIP, that includes soap and water, and the pressure washer. These things rusted together in no time, unoperable.
@@ZZ-jd6vx mine are absolutely perfect! Not one sign of rust or wear, they look and perform brand new, no bullshit!Maybe yours were defective?
@@CaptainLeonsBoatingandMore as defective as a product can be!
Been wanting to get some of these but i hear of people stealing them off the trailer while your out boating around on the lake.
That sucks, what’s wrong with people? They can afford a boat but need to steal straps?
I know it would be a hassle, but I thought about people stealing them and just take them off after unhooking.....@@CaptainLeonsBoatingandMore
Hopefully not worth stealing.@@acflye
My wife's friend commented after I bought my boat that boat stands for.... Bring... On... Another... Thousand..
Boy was she right.
I've been fortunate with my boat being so cheap and efficient to operate. But I hear ya!
I just have to say, that this is the 4th Video that has suggested using a 7/16th Drill Bit!
Like WTF guys......the Bolt is a 1/2" Bolt.....so...try as you might, That 1/2" Bolt is not going to make it, through any 7/16th Hole!
I keep my boat 1/2 hour drive from our place.
So....to get all the way out there, to discover that I needed a 1/2" Drill Bit.....Pissed me OFF!
Yes......I should have checked the Bolt and Nut before I headed out, so that is on me.
BUT......I just thought, that after watching 4 Videos on this "SIMPLE" install........that these 4 guys, knew what they were talking about?
I won't make that Mistake again.
Its a HALF INCH BOLT people.......Take a HALF INCH Drill Bit with you.....Just in case!
DOH!
Ray, are you implying that 4 separate unconnected TH-cam creators each decided to incorrectly state the size of the drill bit they used? For real bro? I’m very careful in the free content and guidance I provide to my viewers. I’m methodical in following manufactures suggestions and guidance. I don’t know the size of the bolts your product came with, as you say that’s on you, but my bolts, my drill bit and even the instructions all said 7/16. Worked perfectly! Thanks for watching.
Drilling through the frame takes time....
You're not kidding, my video makes it look easy, which its not! Thanks for watching.
What brand steel drill bit did you use ? Tips pls.
If you are looking at buying these things for your boat, DON'T!!
I put these things on my brand new aluminum trailer to hold my boat, thinking that all f the "reviews" were good.
After the VERY FIRST trip to the water, the next time out they became hard to release.
I then took them off, sprayed them inside with corrosion X, lithium grease and even MAX WAX!!
They made three trips to the water, after the third trip I had to cut the straps with my knife to release my boat from the trailer.
I currently have two giant chunks of rusted together garbage to show for my money.
DO NOT BUY, unless you like throwing your money away.