Oh my gosh! This helped me so much! I went three years with a dead key fob. I thought I'd have to pay someone to help me. With this video, I got my new fob to work. It's the little things right?!! Thank you!!
Bought a fob and programmer for my 2011 Silverado and in about 1 minute I had 2 fob's programmed. Now I don't have to listen to a horn blowing and having to hurry up and turn the ignition on.
Don’t show off lol. This is why I’m here today. The horn business. I have a 2011 enclave and this type of programming stopped at 2010. 😢 Life is so unfair.
If you can’t get the remote learning in dash it because you have to have a programer plugged into obd 2 then do this. If still a problem then make sure your vehicle does have remote start. Lastly I know some even with the program form store you need a locksmith to add additional software.
@@charlesthon Thank you brother for your quick response :) I hope you give me the widget link because I searched for it and did not reach her on Amazon!
@@charlesthon Thank you brother and grandmother already :) I have another question: Do you know a face that can program the American remote in general?
@@elcamaron19 I don’t think you can just get it installed. Look in your glove box and there should be an extremely long list of 3 digit codes. If yours has ap8 somewhere on it you should be able to buy a new key with remote start buttons and get it programmed. If you can’t program it the dealer should be able to.
REMOTE PROGRAMMING (For vehicles WITHOUT the Driver Information Center (D.I.C.)) 1. Enter the vehicle, close, and unlock all doors using the power lock switch on the driver’s door. 2. Insert a key into the ignition and switch the key as far to the ON position as it will go without starting. 3. Using the trip/odometer reset button, press and release until “RELEARN REMOTE KEY is displayed on the dashboard display. 4. Press and hold the trip/odometer button until “REMOTE KEY LEARNING ACTIVE” is displayed on the dash. Once “REMOTE KEY LEARNING ACTIVE” is displayed on the dash, you have successfully entered programming mode and are ready to program your new remotes. 5. On the first remote you wish to program, press and hold the “LOCK” and “UNLOCK” buttons at the same time and hold for up to fifteen (15) seconds. You should hear an audible chime from the vehicle to indicate that the remote has been programmed successfully. If no chime is heard, release the buttons and try holding them down again. 6. Repeat STEP 5 for all remotes you wish to program. You can program up to four (4) remotes total. 7. Once you have programmed all your remotes, exit the programming mode by turning the key off and removing it from the ignition. 8. Test all remotes to ensure they are functioning. If any did not program, restart the programming procedure from STEP 1 and switch the order in which you are programming the remotes.
My fob lock and unlock is working already, but the button on the top is not, i dont know what is it called..starter? Lol anyways, if i try to reprogram it the way you did, is it possible that everything will work on my fob?
Remote start? Your truck has to have the module for remote start, and the remote start fobs have a 4th button to start the vehicle. The good news is if you have a 2008-2013 Silverado LT trim or higher you can have the factory remote start installed. I had mine done years ago. It was about $350 at the dealership.
I was having the issue where I hold the odometer stem and it wouldn’t activate I would hold the stem up the the 3 secs then 15 secs and it wouldn’t activate any ideas on why I’m having this issue or to get it to work?
bought a reprogrammer for my 2009 Chevy cobalt LT and after I programmed a fob to it, my engine light came on. I ran the code reader and got a p0700 code and u0073 code. This makes no sense why it came on right after I did this but it’s been fine. I only have 89k miles. Any help/ideas why please?
The P0700 code indicates that there's a malfunction with your vehicle's (TCM) Transmission Control Module. This computer monitors your transmission and works with the Powertrain Control Module (PCM) and Engine Control Module (ECM) to shift gears when necessary. First make sure the battery is properly connected. If there is a loose connection, this can cause the code to appear. Additionally, make sure the ground is clean and free of any corrosion. If there is any build-up on the ground, it can cause problems with the electrical system and lead to the U0073 code.
Well that's a bunch of HOGWASH.Why is it that that's the way of the world today.Get your money and never mind that it doesn't work ,who cares the company or the person got what they were after YOUR MONEY. Things are NOT the way they used to be.A person or A company used to be about their WORD, but not any more so sad.😢
REMOTE PROGRAMMING (For vehicles WITHOUT the Driver Information Center (D.I.C.)) or Relearn Key Info Display 1. Enter the vehicle, close, and unlock all doors using the power lock switch on the driver’s door. 2. Insert a key into the ignition and switch the key as far to the ON position as it will go without starting. 3. Using the trip/odometer reset button, press and release until “RELEARN REMOTE KEY is displayed on the dashboard display. 4. Press and hold the trip/odometer button until “REMOTE KEY LEARNING ACTIVE” is displayed on the dash. Once “REMOTE KEY LEARNING ACTIVE” is displayed on the dash, you have successfully entered programming mode and are ready to program your new remotes. 5. On the first remote you wish to program, press and hold the “LOCK” and “UNLOCK” buttons at the same time and hold for up to fifteen (15) seconds. You should hear an audible chime from the vehicle to indicate that the remote has been programmed successfully. If no chime is heard, release the buttons and try holding them down again. 6. Repeat STEP 5 for all remotes you wish to program. You can program up to four (4) remotes total. 7. Once you have programmed all your remotes, exit the programming mode by turning the key off and removing it from the ignition. 8. Test all remotes to ensure they are functioning. If any did not program, restart the programming procedure from STEP 1 and switch the order in which you are programming the remotes.
Oh my gosh! This helped me so much! I went three years with a dead key fob. I thought I'd have to pay someone to help me. With this video, I got my new fob to work. It's the little things right?!! Thank you!!
Thank goodness you discussed and showed where the Odometer stem was located. You saved me from breaking my truck! Thanks again!!!
Sitting here holding the stem down and it only gives option to change language never any other option
Bought a fob and programmer for my 2011 Silverado and in about 1 minute I had 2 fob's programmed. Now I don't have to listen to a horn blowing and having to hurry up and turn the ignition on.
my headache at the moment
It doesnt appear that mode on my 2011 Silverado can you help me
Don’t show off lol. This is why I’m here today. The horn business. I have a 2011 enclave and this type of programming stopped at 2010. 😢 Life is so unfair.
My 13 impala doesn't have odometer trip button like older cars used to. It has a digital type button
It won’t give me that.
The words remote key learning doesn’t show up on my dash…
What year Silverado?
@@jonathangodbout6645 2011
2013 mine doesn't show up either
Will it show up on 2012
Has anyone taken theirs to the dealership ? I don’t wanna buy the programmer for $40
No matter what I do I can’t get what your dash said on my dash. Any help please.
does the remote start work?
This video was so helpful and most importantly EASY. Thank you!!!
If you can’t get the remote learning in dash it because you have to have a programer plugged into obd 2 then do this.
If still a problem then make sure your vehicle does have remote start.
Lastly I know some even with the program form store you need a locksmith to add additional software.
This worked on my '06 Solstice. Thanks.
This doesn’t work on 2012+
Will this not work on a 2012 GMC Sierra SLE?
If not what did/do you/I have to get?
GMC Sierra 2012 I have no settings in this screen !! What do I do to make it appear
U need the doorman kit $70 dll in Amazon
@@charlesthon Thank you brother for your quick response :)
I hope you give me the widget link because I searched for it and did not reach her on Amazon!
@@azizsa1971 justo search dorman keyless GMC 2012 un amazon
@@charlesthon Thank you brother and grandmother already :)
I have another question: Do you know a face that can program the American remote in general?
Thanks again for that had my Yukon for a year and my remote control stopped working but thanks to you got it
Has anyone been able to get the remote start to work?
You have to have RPO code ap8 for the remote start to work
@@jaxon258 where do you get that installed
@@elcamaron19 I don’t think you can just get it installed. Look in your glove box and there should be an extremely long list of 3 digit codes. If yours has ap8 somewhere on it you should be able to buy a new key with remote start buttons and get it programmed. If you can’t program it the dealer should be able to.
2011 Chevy Traverse
Scrolling through all options even, it gives me no “relearn remote” option. Can you please help?!?
I did the steps twice but the remote still isn't working do I need to buy a new one I replaced the battery with new ones also
I have a 2013 but doesn’t show up the relearn remote on dash ?? Any other way I can please
Same
You have to have a obd2 reader I belive
Puedo reutilizar el obd key fob programmer para otros controles en el mismo carro…?
I don’t have that option to relearn. Has anyone else experienced this? If so how did you do it?
I am right now and dont know what i should do
Same exact boat wish we could get some answers
REMOTE PROGRAMMING (For vehicles WITHOUT the Driver Information Center (D.I.C.))
1. Enter the vehicle, close, and unlock all doors using the power lock switch on the driver’s door.
2. Insert a key into the ignition and switch the key as far to the ON position as it will go without starting.
3. Using the trip/odometer reset button, press and release until “RELEARN REMOTE KEY is displayed on the dashboard display.
4. Press and hold the trip/odometer button until “REMOTE KEY LEARNING ACTIVE” is displayed on the dash.
Once “REMOTE KEY LEARNING ACTIVE” is displayed on the dash, you have successfully entered programming mode and are ready to program your new remotes.
5. On the first remote you wish to program, press and hold the “LOCK” and “UNLOCK” buttons at the same time and hold for up to fifteen (15) seconds. You should hear an audible chime from the vehicle to indicate that the remote has been programmed successfully. If no chime is heard, release the buttons and try holding them down again.
6. Repeat STEP 5 for all remotes you wish to program. You can program up to four (4) remotes total.
7. Once you have programmed all your remotes, exit the programming mode by turning the key off and removing it from the ignition.
8. Test all remotes to ensure they are functioning. If any did not program, restart the programming procedure from STEP 1 and switch the order in which you are programming the remotes.
Thanks for the vid'
But all your O-Rielly & direct' links, seem to be disfunctional !
I cant get the remote key learning active mode to display on my 2008 Impala! Any other suggestions appreciated! I have tried all other procedures!
Same here bro
My fob lock and unlock is working already, but the button on the top is not, i dont know what is it called..starter? Lol anyways, if i try to reprogram it the way you did, is it possible that everything will work on my fob?
But how to actually start it? Do you press twice or press and hold
Remote start? Your truck has to have the module for remote start, and the remote start fobs have a 4th button to start the vehicle. The good news is if you have a 2008-2013 Silverado LT trim or higher you can have the factory remote start installed. I had mine done years ago. It was about $350 at the dealership.
Does not work on my 2008 GMC truck
I was having the issue where I hold the odometer stem and it wouldn’t activate I would hold the stem up the the 3 secs then 15 secs and it wouldn’t activate any ideas on why I’m having this issue or to get it to work?
Omg so simple if it dosent work the first time just redo it so glad for you thank youuuuuu so happyyyyy lolll lifesaver video
bought a reprogrammer for my 2009 Chevy cobalt LT and after I programmed a fob to it, my engine light came on. I ran the code reader and got a p0700 code and u0073 code. This makes no sense why it came on right after I did this but it’s been fine. I only have 89k miles. Any help/ideas why please?
The P0700 code indicates that there's a malfunction with your vehicle's (TCM) Transmission Control Module. This computer monitors your transmission and works with the Powertrain Control Module (PCM) and Engine Control Module (ECM) to shift gears when necessary. First make sure the battery is properly connected. If there is a loose connection, this can cause the code to appear. Additionally, make sure the ground is clean and free of any corrosion. If there is any build-up on the ground, it can cause problems with the electrical system and lead to the U0073 code.
How is that done on a 2011 hhr LT
Need mine done as well. I have a 2007 HHR.
Any luck doing this on an HHR?
I don’t have this option on the dash. Is there any other way
ZERO COOL I don't either. Geez
I don’t see the relearn remote key on my dash
Tengo una. Biuk 2014 pero no aparece esa que usted dice como le puedo hacer
They don't work and they don't tell you it is designed to die after 3 used (or tries if it doesn't work -and it doesn't)
Well that's a bunch of HOGWASH.Why is it that that's the way of the world today.Get your money and never mind that it doesn't work ,who cares the company or the person got what they were after YOUR MONEY. Things are NOT the way they used to be.A person or A company used to be about their WORD, but not any more so sad.😢
I was able to get mine to work but I bought the one with the programmer.
What the heck did you do cuz mine beeps but once I press n hold lock and unlock it stops and does nothing......
@@shellrell, I just plugged the receiver that came with the key fob in by my left knee and it did all of it for me...
@@shellrell auto zones printed out instructions on how to do it but i followed the directions that are are on the programmer/receiver.
@@elizabethscott8252 yea that anti work for me
@@shellrell sorry🤔
Doesn't work after 2010 or 2011.
REMOTE PROGRAMMING (For vehicles WITHOUT the Driver Information Center (D.I.C.)) or Relearn Key Info Display
1. Enter the vehicle, close, and unlock all doors using the power lock switch on the driver’s door.
2. Insert a key into the ignition and switch the key as far to the ON position as it will go without starting.
3. Using the trip/odometer reset button, press and release until “RELEARN REMOTE KEY is displayed on the dashboard display.
4. Press and hold the trip/odometer button until “REMOTE KEY LEARNING ACTIVE” is displayed on the dash.
Once “REMOTE KEY LEARNING ACTIVE” is displayed on the dash, you have successfully entered programming mode and are ready to program your new remotes.
5. On the first remote you wish to program, press and hold the “LOCK” and “UNLOCK” buttons at the same time and hold for up to fifteen (15) seconds. You should hear an audible chime from the vehicle to indicate that the remote has been programmed successfully. If no chime is heard, release the buttons and try holding them down again.
6. Repeat STEP 5 for all remotes you wish to program. You can program up to four (4) remotes total.
7. Once you have programmed all your remotes, exit the programming mode by turning the key off and removing it from the ignition.
8. Test all remotes to ensure they are functioning. If any did not program, restart the programming procedure from STEP 1 and switch the order in which you are programming the remotes.
What is my car doesn't have the Key relearn option?
That just for Chevy cars??👍💯
Same thing here
Thankyou
No luck with mine!
I don’t have relearn
great!!!
SCAM
R you serious