Here is a idea you can do to get better flames. Find some way to activate the choke while driving. which will then dump more fuel into the engine, causing more flame
Hook up a 12v coil on a switch to the exhaust plugs and have it also kill ignition when you flip it then hold the throttle wide open and hit the switch. Doing it this way you can have a steady flame for a few seconds while you hold it. You can use a relay to ground the ignition kill when it sees 12v signal from your switch.
I agree with @PorousShark7688 in the fact that if you could flip the choke on then that would give you flames. I just bought the same dual carbs as you have on that engine for my modified mower project. Also, there should be some adjustment in your air/fuel mixture on your carburetors. If you richen up your mixture, you will have big flames all of the time (although it will run like garbage and foul out the plugs on your engine) as long as you give it a tiny bit of throttle. My only advice to you is that you should take note of your current adjustments on your carburetors and when you are done shooting flames, then put them back to how they were. The engine that you used in this video looks like the same one as what you swapped into the primer gray lawn mower that you had on the 70 mph mower challenge part two. It also looks like the same engine as what was in your mower that had the hood covered in stickers (now the honda 650 swapped mower) that you were drifting in town in the winter about 1 year ago. Do you just switch the parts between the mowers for the videos or are they all drivable at any time? Not a bad thing, but I was just curious. Thanks for a great video!
5:24 you need to adjust air/fuel screw usually these type of engines when you give it gas and let it settle back down they idle a little high for about 5 to 10 seconds then lower rpm that's why yours "is bogging" , try reving the engine and wait for the rpms to settle then tune the carb as needed
" In today's video we are going to learn how to bump start a lawnmower " 2 minutes later... " In today's video we are going to learn how to push a mower back home " Yep, you're right haha 🤣
i get backfires on my engine if you set the idle screw fully out so that your throttle valve fully closed after you release the throttle and then normally you get pops and bangs
By the way if you keep your foot on the throttle when you hit the kill switch it will shoot way bigger flames and be way more efficient because you're keeping the throttle blades open which is dumping way more fuel into the engine which is then getting which thing gets shot out the exhaust which gives you even bigger flames
"the engine produces unused gas." -MisterDionne but what you need to make better flames is to put the spark plugs down farther so the gas can ignite easier and it ill make it not only look better but sound better
I think that you may have your spark plugs mounted a little to deep down in your exhaust tubes. Put them almost at the end of the tubes. That way the unburned fuel gets to mix with fresh oxygen and it will burn better.
I put mine right after the exaust port, added some random weedeater coil and it fires after the power stroke, bangs loud and shoots out blue flames. I just turn the iginition off and go downhill last gear, muffler gets red hot
You got the right idea but you have it backwards running lean is not enough fuel. What you mean is running rich when a engine is running rich it is not running efficiently hence causing flames
@@shaneanderson3076 running a engine lean can cause it to lean pop/ misfire running it rich usually makes for more pops on decel/under load but running a hotter plug and running a bit richer would make a great show under load
Take a bike brake handle with the cable and hook the end of the cable to the throttle, then weld the brake handle onto your footeest, but adjust it before you weld so you can reach it
@@MisterdionneYT The one from the back is the one blowing up every time. But if I get a longer one it will have friction with itself and burn because of the tensionner. What should I do ?
@@MisterdionneYT koss quer ton nom pi jtavai ecrit un mesage dans let comment aboit commenr faire des bonne flame ben jpeu lexpliquer icit la so prend les deu spark plug wire de lexhaust mes toe une baterie pi conect sa avec une switch pi sa va faire du consteny fireb
the bogging is due to too much idle fuel its stagnating somewhere in a bend or sum so it sucks too much fuel on idle or complete opposite no fuel at idle
put turbo in lawn mower😂
Make this top comment
Believe it or not, these opposed twin engines, sound amazing when you put a turbo on it. They almost sound like a 12 valve
I would love to hear it with a turbo, would be awesome
Jeje and leave the sparkplugs in for antilag xD
Two turbos
Here is a idea you can do to get better flames. Find some way to activate the choke while driving. which will then dump more fuel into the engine, causing more flame
I tuned the carb on my moped to do that😂. You need a lean idle and a rich wide open throttle. You'll get some loud pops and flames without sparkplugs.
My Honda Navi does that with only an simple Vance and Hines exhaust with the baffle taken out and the carb rejetted
If it has an over head valve you can adjust the valve clearance’s on the exhaust have it open slightly earlier or later
7:41 adhd moment
Hook up a 12v coil on a switch to the exhaust plugs and have it also kill ignition when you flip it then hold the throttle wide open and hit the switch. Doing it this way you can have a steady flame for a few seconds while you hold it. You can use a relay to ground the ignition kill when it sees 12v signal from your switch.
this is it
The stickers make it an engine that increases its power ? this is crazy 😂
Nah those stickers tho💀💀💀💀💀💀
@@Harry_on_60_fps Yes those stickers are something💀💀 Ngl
turn the air fuel screw on the carburetor somewhere close to the idle screw anb have fun 🔥💥
Do you have any video of when you build the suspension?
I agree with @PorousShark7688 in the fact that if you could flip the choke on then that would give you flames. I just bought the same dual carbs as you have on that engine for my modified mower project. Also, there should be some adjustment in your air/fuel mixture on your carburetors. If you richen up your mixture, you will have big flames all of the time (although it will run like garbage and foul out the plugs on your engine) as long as you give it a tiny bit of throttle. My only advice to you is that you should take note of your current adjustments on your carburetors and when you are done shooting flames, then put them back to how they were. The engine that you used in this video looks like the same one as what you swapped into the primer gray lawn mower that you had on the 70 mph mower challenge part two. It also looks like the same engine as what was in your mower that had the hood covered in stickers (now the honda 650 swapped mower) that you were drifting in town in the winter about 1 year ago. Do you just switch the parts between the mowers for the videos or are they all drivable at any time? Not a bad thing, but I was just curious. Thanks for a great video!
I completely died when you lost your words and started beatboxing instea 😂
for real though bro i was on the floor when he started beatboxing
5:24 you need to adjust air/fuel screw usually these type of engines when you give it gas and let it settle back down they idle a little high for about 5 to 10 seconds then lower rpm that's why yours "is bogging" , try reving the engine and wait for the rpms to settle then tune the carb as needed
7:41 😂😂😂😂
You are awesome man i love mower builds keep it up 🙂🙂🙂
7:34 😂😂😂😂
thats some big flames
I like the vibes, and the work! Subbed
love your content, this is what youtube is ment to be, not junk edited and cut clips what everyone else posts
" In today's video we are going to learn how to bump start a lawnmower "
2 minutes later...
" In today's video we are going to learn how to push a mower back home "
Yep, you're right haha 🤣
Bros life is amazing
Love your videos bro literally 💪🏿
Farmers’ Supra😂😂😂
Nice video man !! Love it
The stickers tho💀
don't be suspicious don't be suspicious !!!!!!!
@@MisterdionneYT im not bro i just happened to notice, they look cool bro🥺
+ 30 HP
@@eurotrucksimulator2645 no cap !
pence tu q'un turbo pourrai s'installer dessu ?
Papir pantoute,continue à faire du contenu. 😂❤
if u drill out the jetting on the carb youll throw some good flames
Bro need to make a cop killer lawnmower
i get backfires on my engine if you set the idle screw fully out so that your throttle valve fully closed after you release the throttle and then normally you get pops and bangs
Impressive machine. I love string start. Wish they still sold stuff this way.
I Freakin love that design on that lawn mower engine 😂
To help with belt slip u can drill 1/8in holes in the sides of the pulley that’s what I did on my mud mower it helped alot
Those opposed twins are fucking indestructible torque monsters
I've always had the same idea to put a flame thrower on a mini bike now I know what to do
7:38 LOL
3:50 WHOOHOoŒ
Maybe if you hold a bit the throttle you can have bigger flames, in 4 stroke dirt bikes it works
By the way if you keep your foot on the throttle when you hit the kill switch it will shoot way bigger flames and be way more efficient because you're keeping the throttle blades open which is dumping way more fuel into the engine which is then getting which thing gets shot out the exhaust which gives you even bigger flames
The thing where it bugs if it’s been at idle for too long is because the idle jet is too big😊
You should maybe try amd do some fuel injection conversion
You are the best youtuber ever
Plss show your motor it so freaking cool is it still for sale these days and if yes where Can i look it up
I just found your videos and I’m surprised because they’re awesome….. where are you from?
"the engine produces unused gas." -MisterDionne but what you need to make better flames is to put the spark plugs down farther so the gas can ignite easier and it ill make it not only look better but sound better
I think that you may have your spark plugs mounted a little to deep down in your exhaust tubes. Put them almost at the end of the tubes. That way the unburned fuel gets to mix with fresh oxygen and it will burn better.
I put mine right after the exaust port, added some random weedeater coil and it fires after the power stroke, bangs loud and shoots out blue flames.
I just turn the iginition off and go downhill last gear, muffler gets red hot
You have to kill the engine spark and full throttle the gas to get the flames you want :)
I bet if you adjust the air/fuel ratio rich, put a bigger main jet, and adjust the slide more rich, you could probably have some huge flames lol
Ah et aussi c’est quoi la transmission sur le tracteur dans la vidéo c’est tu avec des poulies ou des gears
All you have to do to make it pro frames high flames is set the carburetor to be more rich mixture of gas
You do not need a turbo you just need to mix the gas ritual in the carburetor by your screw
What lawn mower are you using
Are you still going to put that Honda V4 in a mower? I saw it on your TikTok
no the engine is trashed up it was seized ! there was alot of rust inside the engine
3:35 maudit beau son ça
The best transmission to get for these is either a mst 206 or the better one is the peerless 920
can i still buy the motor
C serait drôle que tu mettes un petit turbo
You should try to build a rear engine riding mower
Would thinner wheels work better?
you have to make it run richer
Unless you are in a welding contest, WHO CARES if you are a bad welder! I am a bad speller but at least my math is gooder
If you like the sound get a harly
damn flames on the lawnmower
give the exhaust a venturie air intake and it will fire always!!!
Its running lean at idle causing it to shoot more flames and engine braking is holding the rpm up to high for it to run lean
You got the right idea but you have it backwards running lean is not enough fuel. What you mean is running rich when a engine is running rich it is not running efficiently hence causing flames
@@shaneanderson3076 running a engine lean can cause it to lean pop/ misfire running it rich usually makes for more pops on decel/under load but running a hotter plug and running a bit richer would make a great show under load
Turbo on that bad boy would be sick
I HAVE IDEA. Put motorcycle chain on lawn mower of no slipping
Now you just need a bug catcher and supercharger
could this also work on a 50CC derbi bike?
Bro needs a egt gauge now 😭
can you make a tutorial on a gas pedal? i am having trouble making one
Take a bike brake handle with the cable and hook the end of the cable to the throttle, then weld the brake handle onto your footeest, but adjust it before you weld so you can reach it
were you driving on 10th line
You make some funny stuff
What is on that engine
How did you make the variable speed mower not blow a belt every 100 ft ?
make one of your belts is probably to short so it stretches to much and snaps
@@MisterdionneYT The one from the back is the one blowing up every time. But if I get a longer one it will have friction with itself and burn because of the tensionner. What should I do ?
Bro spoke Russian for a moment 😂
Ngl if bro is from Canada, he’s most likely from Quebec because of his accent
No he is from new brunswick saint quentin
@@Justin_fourtrax3004x4 yup !
@@MisterdionneYT koss quer ton nom pi jtavai ecrit un mesage dans let comment aboit commenr faire des bonne flame ben jpeu lexpliquer icit la so prend les deu spark plug wire de lexhaust mes toe une baterie pi conect sa avec une switch pi sa va faire du consteny fireb
get some dragons breath and put it on the exhaust tip it will have clouded flames
Salut j'ai une question pourquoi tu parles anglais dans tes vidéos si tu es français ?
Replace flywheel with aluminum or it'll splode. Common issue with those
where can i find parts for these engines tho ?
Kickass.
PLZ DO MORE
thats cool bro
Chefs kiss
the bogging is due to too much idle fuel its stagnating somewhere in a bend or sum so it sucks too much fuel on idle or complete opposite no fuel at idle
Bro got an after burner
Could you imagine getting chased down by police Horseman on that?
Someone beat me to it but definitely put a little turbo on it.
Put the two exhaust together
When are you gonna put a motercycle engine in a lawn mower? 😅
Would be cool but definitely more fun to try to make a slow motor fast imo lol
what lawn mower body is it
why you put the gas pedal on the wrong side
The clutch is on the right
@@Gavinadcock-q2z i could never drive like that haha
@@Noobplayzyt I probably couldn't either but a good amount of mower pedals are on the right
nice, you need to do some work to that crankshaft tho, poor thing is abliterated lol
yeah it is abliterated hahaha
thats insane
What transmission is that?
pearless 6 speeds
What mower is that pls I’m gonna put a 100cc engine in it it’s going to be my Daly driver
This guy MMMMUUUUUSSSSSTTTTTTTTT be from Alberta (with a BC attitude!)
Can I buy it?
Open the throttle when you hit the kill switch.
You should turbo your lawn mower
i want one soo bad
I need a modified mower again..😢
Dude, you should buy my turbo. Craftsman thing will go about 100 mph.