@sadiagnostics so do I just undo the bolts on the two silver ends of the old fuse and just pull out.? Or i have to twist it in a certain way before pulling it out. Thanks
I bought a CLA250 2020 on auction front end collision everything worked perfectly fine it would turn on. Started replacing little stuff it needed and now no power at all could it be that Pyro fuse even tho it would work fine without changing it before?
My Maserati airbag deployed car won’t start I didn’t get in accident tho do you if this is same situation for Maserati the battery is in back can u help me figure this out
I Own.A 2020 ClA 250 I followed your advice and bought and replaced the PYRO-FUSE but it still doesn't start I don't think the diagnostic machine I have is able to properly Communicate with the system I took it to a shop and the guy said my starter was out and could be why its not starting, could this be true ? or do I keep searching for someone who is able to reset it ?
Hello. Can you give me a answer PLEASE. I have a Mercedes Benz C350e pluginhybrid. It dosent start after a crash on back bumper. Just the driver Seatbelt has been Triggered. I charge the 12v battery and then running out of Power. PLEASE HELP ME. Thanks 🙏🏻
Hey, I’ve got a w205 c300 from auction with front end collision. Can’t find the pyro fuse around the battery so assuming it doesn’t have one. Vehicle doesn’t start and i’m assuming because the srs module crash data needs clearing. i have a maxicom mk908p. When i try to get into SRS it asks to unlock. When i do manual comission it says lCM31 (Supplemental restraint system control module) is defective” any idea what that means?
How did you get on with this? Did you find a pyrofuse? I also have a W205 with blown airbags. wont start. Do I just need to clear the crash data with autel?
@@johnnydepp1391 I’ve shown you where pyrofuse is on this a class also you need to use Similar or machine to reset the crash data other wise it doesn’t start
@@sadiagnostics It's no where to be seen on the W205 which is why I've asked @vadimas Dulko how he got on as he also came across the same issue as me. Might it be that there isn't a pyro fuse on the W205?
Advice for a 2020 a220 that was crashed . Doesnt turn over . Would it just be that fuse to change or does the a220 have another fuse i should replace to start it ? Also wondering where i could find front end diagram to rebuild front end. Cant seem to find any type of diagram for this mercedes .
Yes , bridge the pyrofuse, and also unlock the start/crank with a scanner . Alsochsbge your auxiliary battery in middle console and make sure your main battery us fully charged. Also if motor is seized up with a long break bar turn over the crank by hand. Often motor feels stuck/frozen . Just needs some force to turn over. After that should be good to go.
Hi mate can you please advise me i have just replaced a mercedes w204 2009 drivers door after it was damaged now it has airbag light on i have plugged it in and it is saying that the airbag pressure sensor is faulty does the crash sensor need to be programmed to the car
Thanks for your time the door in question has not been crashed, will the door crash sensor detect a crash that has happened to a different part of the car, as i bought the drivers door from a breakers fitted it to my car ? Thanks
@sadiagnostics once I undo the bolt to the pyro fuse, do I just pull it out or there is a method to it like I have to twist it or something to get it out or could you be kind enough to make a video of you actually taking and replacing the pyro fuse please thanks
![PURPEECH - นี่ฉันเองคนที่... (It's me) [Official MV]](http://i.ytimg.com/vi/NuhHd0hOOg8/mqdefault.jpg)
I just changed one on a 2022 Porsche 911. Pain in the ass
Yeh the newer the cars get the worser it is to work on…
Can you make a video 9f you changing the pyro fuse please
@@MrJamjam0021 unfortunately I’m unable to as this car is long gone…
@sadiagnostics so do I just undo the bolts on the two silver ends of the old fuse and just pull out.? Or i have to twist it in a certain way before pulling it out. Thanks
Good work, keep it up
@@ShahSafi thank you for the feedback :)
is it the same for v177 ,2020 hybrid 250e because i can't find it as u show on this video
Did you find it? I can't find it also.
I bought a CLA250 2020 on auction front end collision everything worked perfectly fine it would turn on. Started replacing little stuff it needed and now no power at all could it be that Pyro fuse even tho it would work fine without changing it before?
@@JuanP-o2b no doubt it it maybe a case did just doing a reset crash on Ismail’s diagnostic tool…
Where can I purchase a pyrofuse ?!
My Maserati airbag deployed car won’t start I didn’t get in accident tho do you if this is same situation for Maserati the battery is in back can u help me figure this out
I Own.A 2020 ClA 250 I followed your advice and bought and replaced the PYRO-FUSE but it still doesn't start I don't think the diagnostic machine I have is able to properly Communicate with the system I took it to a shop and the guy said my starter was out and could be why its not starting, could this be true ? or do I keep searching for someone who is able to reset it ?
You need a factory scan tool ideally or a autel with an ecu programmer which is over 1,000.
do you think seatbelt would blow this pyro fuse
@@johnlerigo9703 yes it’s to do with the safety system
Hello. Can you give me a answer PLEASE. I have a Mercedes Benz C350e pluginhybrid. It dosent start after a crash on back bumper. Just the driver Seatbelt has been Triggered. I charge the 12v battery and then running out of Power. PLEASE HELP ME. Thanks 🙏🏻
@@hikmatahmadzai9217 I’ll not start if airbag has been triggered you need to do what I’ve done plus reset it using diagnostic tool
Hey, I’ve got a w205 c300 from auction with front end collision. Can’t find the pyro fuse around the battery so assuming it doesn’t have one. Vehicle doesn’t start and i’m assuming because the srs module crash data needs clearing. i have a maxicom mk908p. When i try to get into SRS it asks to unlock. When i do manual comission it says lCM31 (Supplemental restraint system control module) is defective” any idea what that means?
Hi sometimes it does this with specific autels and also you have to sometimes try more than once to get the system unlocked…
How did you get on with this? Did you find a pyrofuse? I also have a W205 with blown airbags. wont start. Do I just need to clear the crash data with autel?
@@johnnydepp1391 I’ve shown you where pyrofuse is on this a class also you need to use Similar or machine to reset the crash data other wise it doesn’t start
@@sadiagnostics It's no where to be seen on the W205 which is why I've asked @vadimas Dulko how he got on as he also came across the same issue as me. Might it be that there isn't a pyro fuse on the W205?
Also my dash doesn't light up without me putting 12v power pack on the battery.
Advice for a 2020 a220 that was crashed . Doesnt turn over . Would it just be that fuse to change or does the a220 have another fuse i should replace to start it ? Also wondering where i could find front end diagram to rebuild front end. Cant seem to find any type of diagram for this mercedes .
Did you figure it out? I have the same problem with same car?
Yes , bridge the pyrofuse, and also unlock the start/crank with a scanner . Alsochsbge your auxiliary battery in middle console and make sure your main battery us fully charged. Also if motor is seized up with a long break bar turn over the crank by hand. Often motor feels stuck/frozen . Just needs some force to turn over. After that should be good to go.
Thank you! Will try this
I have a teaching transmission on my dashboard after attempting to change rear breaks on my aclass w177 anyway I can contact you ?
This is your solution
th-cam.com/video/nxM1Zj9WjIY/w-d-xo.html
@@sadiagnostics hello I’ve tried that way a few times nothing seemed to work I’m guessing last result is using a diagnostic machine?
@@2FAZEGAMING unplug battery and plug it back on. Not a good idea but you can try this other solution.
@@sadiagnostics yeah tried that too one time timer went down to 15 not fully so I’m guessing I’ll have to maybe get it reset or removed by machine
which one is that?
Hi mate can you please advise me i have just replaced a mercedes w204 2009 drivers door after it was damaged now it has airbag light on i have plugged it in and it is saying that the airbag pressure sensor is faulty does the crash sensor need to be programmed to the car
No but if you open the door card there’s a crash sensor that needs replacing as it’s faulty and has detected a crash in its life time
They are roughly £40 on eBay
Thanks for your time the door in question has not been crashed, will the door crash sensor detect a crash that has happened to a different part of the car, as i bought the drivers door from a breakers fitted it to my car ? Thanks
@@deedee12386 yes it will detect it sometimes it just triggers.
Ok thanks for your reply
Could the same thing happen after a remap
@@crognjoharding9447 no doubt it it would relate to the file that they’ve done
Is this the same for a 1997 C230! Please helppppppp someone?
No don’t think they had any safety for 1997 cars like they do now
Yours maybe fuel related etc…
Where is it located 1:15
@@georgeSogopoulos am lost what you mean
@sadiagnostics once I undo the bolt to the pyro fuse, do I just pull it out or there is a method to it like I have to twist it or something to get it out or could you be kind enough to make a video of you actually taking and replacing the pyro fuse please thanks
Where can I purchase a pyrofuse ?!
Where can I purchase a pyrofuse ?!