Sidewinder X2 Step By Step Klipper Installation And Setup Guide Including Configs and Macros

แชร์
ฝัง
  • เผยแพร่เมื่อ 9 พ.ค. 2023
  • Follow this simple,complete step by step guide to install and configure Klipper on your Artillery Sidewinder X2. All required configs are included n the download link below.
    Klipper Configs; drive.google.com/file/d/1XB76...
    Get your RPI here; shorturl.at/rsKWX
    RPI Imager: www.raspberrypi.com/software/
    Putty: www.putty.org/
    Pronterface: github.com/kliment/Printrun/r...
    STM32 Programmer: www.st.com/en/development-too...
    Klipper Installer And Update Helper: github.com/th33xitus/kiauh
    Klipper sample configs: github.com/Klipper3d/klipper/...
    Klipper Website: www.klipper3d.org/
    Subscribe; th-cam.com/users/subscription_c...
    Join our Discord server: / discord
    Visit our website; www.etherealproject3d.com
    Buy Me a coffee; www.Ko-fi.com/etherealproject3d
    Follow us on Facebook; / etherealproj. .
    Follow us on Instagram; / etherealpro. .
  • แนวปฏิบัติและการใช้ชีวิต

ความคิดเห็น • 329

  • @rodbacon9489
    @rodbacon9489 11 หลายเดือนก่อน +10

    I've been running Klipper on my SWX2 for quite some time, and was about to switch back to Marlin when I found your video. The information, configs and macros you've provided have transformed my printer into what I always hoped it would be.

    • @EtherealProject3D
      @EtherealProject3D  11 หลายเดือนก่อน +1

      Awesome, thank you very much. Im glad its working better for you now.

    • @rodbacon9489
      @rodbacon9489 11 หลายเดือนก่อน

      @@EtherealProject3D One question. What is the fan duct you're using? I haven't replaced mine yet.

    • @EtherealProject3D
      @EtherealProject3D  11 หลายเดือนก่อน

      @@rodbacon9489 its my own design for a 5015 fan.

    • @rodbacon9489
      @rodbacon9489 11 หลายเดือนก่อน +1

      @@EtherealProject3D is it available for download anywhere? I'm about to fit a 5015 to my SWX2 and have printed a duct from Thingiverse, but yours looks interesting.

    • @rodbacon9489
      @rodbacon9489 10 หลายเดือนก่อน

      Found it online. Thanks.

  • @yodhanhunter
    @yodhanhunter ปีที่แล้ว +1

    Awesome. This is going to help a lot this weekend when I get my X2 on Klipper

  • @ChrisChiapoco
    @ChrisChiapoco 11 หลายเดือนก่อน

    Thanks mate. Yours is by far the best instructional video for this - appreciate you!

    • @EtherealProject3D
      @EtherealProject3D  11 หลายเดือนก่อน

      You are very welcome, and thank you.

  • @Flopshoubox
    @Flopshoubox 3 หลายเดือนก่อน

    First print is currently running !
    Your video is incredible !
    Thanks a lot !

    • @EtherealProject3D
      @EtherealProject3D  3 หลายเดือนก่อน

      You are very welcome, thank you.

  • @oddy_gg
    @oddy_gg 6 หลายเดือนก่อน

    KIAUH makes this so much simpler. Thanks for showing

  • @SimonGrimm1983
    @SimonGrimm1983 2 หลายเดือนก่อน

    Amazing video, i have "klippert" my X2 now. It was so easy, thank you

  • @andyw8009
    @andyw8009 5 หลายเดือนก่อน +2

    I'd like to say big thank you for motivation to get Klipper on my SWX2. I have got a BTT Pi v1.2 so I could skip couple of steps but overall your instruction walked me through with no problems. Great job!

    • @EtherealProject3D
      @EtherealProject3D  5 หลายเดือนก่อน +1

      You are welcome. I love those BTT Pis, they are great

  • @christoskarantanis
    @christoskarantanis หลายเดือนก่อน +1

    This video still helps all sidewinder owners a year after posting! Thank you very much for your help!

  • @johnmichael3740
    @johnmichael3740 หลายเดือนก่อน

    I have to say these videos were extremely helpful to me, I was reluctant to install Klipper and I did face quite a few challenges but in the end things are working quite well and it is on to input shaping! Thank you.

    • @EtherealProject3D
      @EtherealProject3D  หลายเดือนก่อน

      Awesome, I am happy I have been helpful.

  •  10 หลายเดือนก่อน

    Fantastic video ! Thanks for the video and for the support files too. 👍

  • @HiHoSilverAway76
    @HiHoSilverAway76 ปีที่แล้ว +5

    Just got Klipper on Linux (old laptop) and my X2 thanks to the help of your video. Took me awhile to figure everything out(board didn’t want to flash as it was stuck in a bootloop) but definitely appreciate your time explaining each step!

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว +3

      Thank you for watching and for your comment. I hear the bootloop is caused by the stock probe. I did not know this till after uploading this video. Im glad this was helpful for you all together. Have fun with klipper.

    • @ova1435
      @ova1435 6 หลายเดือนก่อน +1

      Hi, I also have the stock probe and intend to migrate to Klipper soon... How did you fix your bootloop ? Do you have any links that would be interesting to read before installing Klipper?

  • @bamboo9840
    @bamboo9840 7 หลายเดือนก่อน

    Thank you very much for sharing your knowledge!

  • @redline3036
    @redline3036 ปีที่แล้ว +1

    Your the man took me maybe 30mins to get setup. Now I just need to do the linear rails that you did and ill be good.

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      Awesome, im glad it worked for you.

    • @redline3036
      @redline3036 ปีที่แล้ว

      @@EtherealProject3D Easiest klipper install I've ever done was really really easy. Already have your board installed its just makes it that much better. Bummed I missed out on the flexplates but thats ok my fault for not getting one when I should have.

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว +1

      @@redline3036 sweet, im glad i was able to make it easy for you. I still have a couple of the flexplates. I am figuring out a new manufacture as well. The ones I have left got some damage that makes them un sellable at full price. For those that want one I am willing to sell them at a discount to replace the cost but they are not in perfect condition. Email me if you are interested.

  • @JJiMedia
    @JJiMedia หลายเดือนก่อน

    Thank you so much for this awesome guide. I was aware of Marlin before and was preparing to flash my SW X2 with it, but running to this, and having an extra Raspberry Pi 3B with a 5" display lying around, I decided to follow this path instead, and I have to say I'm not dissappointed. Klipper has everything I need and more and with all the bells and whistles with bed leveling and heightmap, the first layer test print looked perfect with zero need for any tweaking.
    The only hurdle I ran into was the flashing. The verification failed and I needed to do a full chip erase first before I was successful in getting the firmware flashed successfully. One thing you should have mentioned was that once you flash the firmware, the TFT on the X2 will no longer do anything and show all zero values, just so that those new to all this won't be too concerned (as I was at first until I realised you actually control everything either from the web interface or KlipperScreen.
    You've got one subscriber more. Keep up the good work!

  • @manuelhaibock8662
    @manuelhaibock8662 9 หลายเดือนก่อน +1

    Big THX for this Video. So i was able to run Klipper for my Genius Pro. It's working perfect and it's so much faster. Maybe you can need the printer.cfg for other people. Now it's not perfect but i have to get used to it. Happy printing

  • @PaulLemars01
    @PaulLemars01 11 หลายเดือนก่อน +1

    Excellent video for installing Klipper. However, I have what I guess is a noob question. Why? what benefits are there for running Klipper on the X2. I've been running mine since it first came out and it's worked out really well for me. It's my third printer after the ubiquitous Ender 3 and an Anycubic Linear Kossel both of which still work perfectly albeit noisily. I tend to design and print functional parts that we use around the apartment or for friends. Speed of printing is not a big issue for me, in fact quietness of operation is the most important consideration since we have to live with our printer in the family room. I like to use Octoprint since that way I can monitor a print when I'm out and about and the RPI3 that it runs on seems to work nicely with the stock Marlin although the print quality could be a bit better. Will Klipper appreciably increase the print quality? I've heard about input shaping but I don't understand how you could integrate a sensor module on a bed slinger. It seems to me that proponents of Klipper tout the increase in print speed as the main benefit but I wonder what I'd be giving up. For example, Klipper seems to be more complex and time consuming to use than my simple Octoprint interface. Nonetheless thank you so much for what is undoubtably the best instructional video on how to achieve Klipper on the X2.

  • @BradRochford
    @BradRochford 5 หลายเดือนก่อน

    Thank you for this amazing step by step guide on this complicated install. I had to pause and rewind a couple of times but got it all in the end. There were a few scripts that I had to adjust in the configs but it was pretty straight forward. Now I am just fine tuning my z offset and getting Cura to play nice.

  • @HarelBenSheffer
    @HarelBenSheffer 9 หลายเดือนก่อน

    Great tutorial! Thank you.
    I was very apprehensive about switching to Klipper, mainly because of flushing the printer's firmware...
    Once done, got my first layer perfectly thanks to the leveling tools.
    A question, though: why does a print take so long to start (up to 5 minutes) or it does not start at all? the console shows "File selected" and that's it... Need to use the emergency stop and then reset for it to work again.

  • @mamlvagensinan6832
    @mamlvagensinan6832 ปีที่แล้ว +1

    Thanks!
    Keep up the good work

  • @berndsemmelhuber6266
    @berndsemmelhuber6266 หลายเดือนก่อน

    Thanks for the great instructions. The firmware update worked immediately. Now I'm looking for a good klipper profile for the OrcaSlicer. Do you have a good recommendation for this?

  • @mamerghojal965
    @mamerghojal965 10 หลายเดือนก่อน

    fantastic video , what would make it a complete guide is a follow up on some of the errors that you might encounter .
    for example the m997 command didn't work for me and i hade to open the printer and install a jumper .
    also my pc didn't see the printer until i turned it off and only powered it from usb

    • @EtherealProject3D
      @EtherealProject3D  10 หลายเดือนก่อน

      Thank you, and thanks for the video idea, i might just have to do that.

  • @goldesenor9475
    @goldesenor9475 7 หลายเดือนก่อน +1

    I had to adapt some stuff to genius pro but great stuff! thank you!

    • @EtherealProject3D
      @EtherealProject3D  7 หลายเดือนก่อน

      your welcome

    • @EGuy1974
      @EGuy1974 3 หลายเดือนก่อน

      Could you please share the modified files for genius pro?
      TIA

  • @cyberfly8452
    @cyberfly8452 9 หลายเดือนก่อน

    Excellent video thanks !!! 💪

  • @Der_Chefschweisser
    @Der_Chefschweisser 9 หลายเดือนก่อน

    One of the best Tutorials.Everything went fine ..till i upgraded klipper.I dunno why but the firmware wouldnt connect.Mcu so i had to reupload usin dfu mode with jumper.But thankfully after some 8 hours i finally managed the basics.thx

    • @EtherealProject3D
      @EtherealProject3D  9 หลายเดือนก่อน

      You need to define it in the cfg

  • @ova1435
    @ova1435 5 หลายเดือนก่อน

    Very instructive video.
    I see in printer.cfg this section for the case fan, but I'm wondering if this is correctly configured... according to Klipper doc a controller_fan should be associated with heater or an active stepper driver
    [controller_fan case]
    pin: PC6
    off_below: 0.3
    idle_speed: 0.0
    How is this supposed to control the case fan?

  • @IgorDeCamps
    @IgorDeCamps ปีที่แล้ว

    Excellent Video, Short and sweet. The only thing I find annoying on these Ruby boards is having to short the PINS to update the Klipper Firmware on the MCU. Going to install a little switch externally to short the pins for Bootloader mode, whenever I need to flash... Klipper is going through constant updates.
    Q: Does one of those configs include the Induction Bed level mod you did earlier?

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว +2

      Thank you. Yeah I dont know why they did not include a bootloader on this board, seems like an easy thing to have, the switch is a good idea for sure. To answer your question, no it does not, I had trouble getting to work correct and for the sake of time I switched back to the CR-Touch to get this video done.

  • @Avrution
    @Avrution ปีที่แล้ว

    This is on the list after the linear rails are done.

  • @iglhamm
    @iglhamm 8 หลายเดือนก่อน

    Hi, great video!
    But whats the reason behind your rotation_distance numbers in your config? You're using odd numbers like 39.94 and 7.96.
    All other X2 Klipper configs online use like 40 and 8 respectively. I even think I read somewhere that Klipper internally rounds those numbers anyway.

  • @Flecoide
    @Flecoide 8 หลายเดือนก่อน

    Gracias!!! muy buena explicación!!!

  • @CiroAnacleto
    @CiroAnacleto ปีที่แล้ว

    Excelent video ! I bought my new Sidewinder X2 and I am considering to install klipper on it. I am thinking in to buy a MKS pi instead of Raspberry pi. I have a question:
    The stock screen will be still able to controll the printer after the firmware upgrade or it will be only controlable by the web interface ?
    Thank you

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว +1

      With klipper the stock screen does not function. If you get the mks pi I recommend getting a compatible screen that works with the mks pi so you can have the klipper screen interface along with the web interface. Thank you for watching and happy 3d printing.

  • @gaboxargentina
    @gaboxargentina ปีที่แล้ว

    Amazing video thanks

  • @alxzeu
    @alxzeu 10 หลายเดือนก่อน

    Hi, I know I shouldnt be talking as THIS particular channel has only 17 subscribers, but I had another channel in the past and would recommend making the title shorter and more summarising, this got me 10x more views. loved the video thank you.

  • @bananatubeOG
    @bananatubeOG ปีที่แล้ว +1

    If for whatever reason you're getting the error message ""Option 'serial' in section 'mcu' must be specified" after setting the mcu id, make sure the # before serial: is removed, or the line will not be active. silly mistake I made, as the # was present, unlike how it is in this video. hope that helps anyone.

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      You need to uncomment the [mcu] section in the printer.cfg file

  • @horacioramos6484
    @horacioramos6484 9 หลายเดือนก่อน

    excelent! i have a question, can we change the home location with klipper?

  • @wernercoetz
    @wernercoetz 3 หลายเดือนก่อน

    Thank you for the video, i have not yet watched the entire video. I was wondering can i run this tutorial on my Creality Ender 3 S1 pro? Thanks in advance.

  • @BooshmanLee
    @BooshmanLee ปีที่แล้ว

    Informative video. Much different to doing this in an X1?

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว +1

      Thank you. The process should be pretty similar on the X1.

  • @andriitsarenko1696
    @andriitsarenko1696 4 หลายเดือนก่อน

    Hey! Thanks for tutorial, I've followed your steps without issues. The only issue I see for now, that macros for filament load retracts filament too much, and on print start filament extruded a bit later then print starts. It's not a big issue on start print, but on change filament in the middle of printing I think it could be an issue.

  • @Godrik4822
    @Godrik4822 ปีที่แล้ว

    Great video! Please keep up the good work and start a Patreon :P I would sub just for the contecnt on the SW X2. Thanks again.

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      I am on kofi, its like patreon. Link is in video dicription. Thank you.

  • @jplorge
    @jplorge ปีที่แล้ว

    Hello, thank you for all these very instructive and pleasant videos. I am still on a SWX1, without BLtouch. but klipper is installed.
    I've heard of a full metal heating head to get up to 300°C, is this valid, or is it better to switch to another printer? speed is not the most important thing, but learning about the novelty that is klipper allows you to stay up2date at no cost. I'd also like to know if you've ever heard of or seen a SWX1 with the head and motherboard of a SWX2, do you think it could work. the mechanical base is identical, isn't it? except for the blue plactic gantry on the swx2.
    Thanks in advance for the answers even if you don't have any more information than I do. Good job mod. on this Artillery. thanks.

    • @velocistafpv
      @velocistafpv ปีที่แล้ว +1

      I'm using an X2 with the all-metal hotend and have been printing 280+ deg on the extruder with no issues. Sidewinders are very capable 3D printers.

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      Yes they are.

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      Thank you for your kind remarks, It helps to know that people are enjoying my content. As far as using the SWX2 electronics in an X1, Its doable but there are some differences that are hard to notice at first glance. The breakout boards are all different and the tool head uses a 24 pin ribbon cable on the X2 rather than the 20 pin on the X1. You could just switch out the mainboard if you wanted to, but would take a few changes to the wiring inside as well.

    • @jplorge
      @jplorge ปีที่แล้ว

      @@EtherealProject3D Thank you for your reply, I now have a better idea of the differences between the two models. I'm going to stay with the X1 and get used to learn Klipper. One more question, you have made an electronic card to connect a BLtouch, do you know the cost to Europe? if you still have some in stock too.

  • @danielesebastiani9905
    @danielesebastiani9905 ปีที่แล้ว

    Great video, if I have the flsun v400 with the speeder pad , can I configure it to work instead to buy a raspberry ?

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว +1

      I am not sure, Ive not had any experience with speeder pad so I cant speak to any specifics about it.

  • @chrissadler241
    @chrissadler241 ปีที่แล้ว

    Awesome Thanks! Shared hop you dont mind :)

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว +1

      Your welcome, I dont mind at all, thank you for sharing.

  • @tysonhaas179
    @tysonhaas179 8 หลายเดือนก่อน

    Hello. I’m rand new to 3D printing and just bought a SWX2…can you explain to me what the purpose of this is and what benefits it has?

  • @anishnattamai8801
    @anishnattamai8801 11 หลายเดือนก่อน +2

    Can you make a tutorial for a Artillery-Genius? If not, is there a config file i can use, and follow this tutorial?

  • @hatta1991
    @hatta1991 5 หลายเดือนก่อน

    Great toturial, thanks!
    I run my X2 since one year on Klipper and due to problems I switched over from the SonicPad to the Bigtreetec Pad7.
    Can you show, how to make the resonance control in Klipper? Would be great 😁
    Thanks and greetings

    • @EtherealProject3D
      @EtherealProject3D  5 หลายเดือนก่อน +1

      Thats going to be mondays livestream

    • @hatta1991
      @hatta1991 5 หลายเดือนก่อน +1

      @@EtherealProject3D oh yeah 😁 looking forward to it 😎

  • @konradduncan817
    @konradduncan817 7 หลายเดือนก่อน

    Great video, really well explained, I'm using Orca Slicer, but the "PRINT_START" and "END_PRINT" doesn't work, klipper never gets to send the extruder to heat up, do you know why it could be?

    • @alejandrojo7628
      @alejandrojo7628 6 หลายเดือนก่อน

      Can you Name the exakt Error?

  • @samvanlaecken856
    @samvanlaecken856 ปีที่แล้ว

    Awsome video. I am still using the swx1 with a bltouch and hemera extruder ( using your bracket designs). I am looking into installing klipper. Would the printer.cfg file be good base start for my printer?

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว +1

      Thats a great setup on the X1 for sure. The X1 will have a pretty different config setup, check out 3D Print Beginner, he has a klipper config for the X1 that would be a good starting point.

    • @samvanlaecken856
      @samvanlaecken856 ปีที่แล้ว

      Sweet thank you

    • @Nealio139
      @Nealio139 ปีที่แล้ว

      Hi sam were you able to find the config files for the x1? I wasn't able to find it. would you be able to link them to me if you found it?

  • @MrRataj04
    @MrRataj04 11 หลายเดือนก่อน

    interesting solution, have you ever encountered a situation where during printing sometimes a layer of the y axis or a lot of layers move during printing?

    • @EtherealProject3D
      @EtherealProject3D  11 หลายเดือนก่อน

      No, I have not had that problem.

  • @fotogeekbrix
    @fotogeekbrix 10 หลายเดือนก่อน +1

    Hi! Thanks for a thorough video 🙂
    I have a SWX1.
    Is this directly transferable to this model?
    Thanks ;-)

    • @familyj4715
      @familyj4715 4 หลายเดือนก่อน

      Was it? Also same boat as you

  • @giovox9127
    @giovox9127 3 หลายเดือนก่อน

    Hi, thank you for this fantastic guide, unfortunately after 3 weeks of use it no longer works. I did several tests and came to the conclusion that the motherboard firmware was corrupt. i connect the PC to try to flash Klipper/Marlin again, the printer is not recognized by Windows (I installed the drivers, and I also tried with the manual dfu). What could I do? thanks for your time.

  • @KarstenBecker36
    @KarstenBecker36 5 หลายเดือนก่อน

    Hi there, i followed your tutorial today and am now at the hightmap thing.... I have a deviation of 0.400mm and the map picture looks like mt everest.... What can i do about that. It took several tries to get the printer to printing, i had to install ideamaker and only then it started printing, BUT the extruder ripped the first layer off the bed....i think i need help here

  • @sargentokoala
    @sargentokoala 7 หลายเดือนก่อน

    how do you manage a sonic pad with sidewinder x2, will you please make a video??

  • @Mysguyded40
    @Mysguyded40 9 หลายเดือนก่อน

    I was about to do this, but saw a Q/A on an earlier post about the bed leveling iduction mod. Am I correct to assume if I have done that mod, I cannot follow this tutorial and get Klipper to work or has this been updated?

    • @EtherealProject3D
      @EtherealProject3D  9 หลายเดือนก่อน

      you will have to change the probe settings in the config.

  • @gaming4alll
    @gaming4alll หลายเดือนก่อน

    Awesome video. Do you by any chance have a config file for the Original Artillery Genius?

    • @EtherealProject3D
      @EtherealProject3D  หลายเดือนก่อน

      Thank you very much. I do not, sorry.

  • @stephenmills5133
    @stephenmills5133 ปีที่แล้ว

    Never had a perfect first layer till now , just got tweek my cura profile for this , thank you for all the advice and help , if you have any hints for a good cura or prusaslicer profile i be grateful

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      Awesome! Im happy I could help. I use IdeaMaker for slicing sorry.

  • @idarstomsvik5439
    @idarstomsvik5439 ปีที่แล้ว

    Excellent video, i finished upgrading to Klipper this afternoon, and i noticed that the filament runout sensor isn't working anymore. Do you have a solution for that?

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      It will have to be connected to one of the endstop plugs on the mainboard a d defined in the printer.cfg

  • @MarkusThomaen
    @MarkusThomaen 4 หลายเดือนก่อน

    Hello, i want to change my X2 to clipper. Can I flash the bin file on your google drive to my x2 like this? Sorry I'm from Germany and my English is not the best. Thanks for this great guide.

  • @jsss00000
    @jsss00000 9 หลายเดือนก่อน

    Thanks for your tutorial, followed it and got Klipper on my sidewinder. I only have one problem, corners are not as good as they were on marlin, is there anything i can do to fix it? Thanks!

    • @EtherealProject3D
      @EtherealProject3D  9 หลายเดือนก่อน

      Your welcome. You should tune pressure advance

  • @zerixscz6327
    @zerixscz6327 7 หลายเดือนก่อน

    Hi. Great video. I have one question. Is it possible to connect the printer via wifi, if so can you make a video about it. I’m kinda noob in this things.

    • @EtherealProject3D
      @EtherealProject3D  7 หลายเดือนก่อน

      With the RPi you will have wifi by default and you can access the machine via the web interface.

  • @cedricbertrand3048
    @cedricbertrand3048 6 หลายเดือนก่อน

    Hello, first: thank you for this video! Can you tell me if you figured out how to manage the filament runout through klipper? I know I need to unplug the filament sensor from the TFT first and then plug it to a free pin on the mother board of the SWX2 (pin PA0), and with a special setup in the Marlin firmware, this can work and allow for example Octoprint (on a RPI) to be aware when the filament runout is triggered. Do you have the same configuration but for klipper? Thanks.

    • @EtherealProject3D
      @EtherealProject3D  6 หลายเดือนก่อน +1

      I do not yet but will be adding that feature in the near future.

    • @cedricbertrand3048
      @cedricbertrand3048 6 หลายเดือนก่อน +1

      @@EtherealProject3D Great! Thanks

  • @UzunKamis
    @UzunKamis 3 หลายเดือนก่อน

    I would like to ask something on start/end.cfg files. I have pasted when I have in Cura in these cfg files respectively. Should I remove what I have in Cura in Start G-Code and End G-Code?

  • @geauxracerx
    @geauxracerx 10 หลายเดือนก่อน

    I’m setting up to try this with the Genius Pro. I took your config and changed the build dimensions to what the Genius Pro’s are. Do you think this will work since they are pretty much the same machine just the sidewinder is bigger.

  • @HiHoSilverAway76
    @HiHoSilverAway76 ปีที่แล้ว

    Hi there, commenting again. Would the screw_tilt_adjust work for other printers on Klipper? I am trying to get my Anycubic Chiron to level but running into my height map all over the place. I apologize for asking on a Sidewinder video but you seem very knowledgeable about Klipper/etc.

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      Yes it will work on the Chiron, you will need to make sure you have the coordinates of the bed screws and offsets correct in the printer config. No need to apologize, I welcome any questions and am happy to provide help.

    • @HiHoSilverAway76
      @HiHoSilverAway76 ปีที่แล้ว

      @@EtherealProject3D I appreciate you getting back to me, but looks like I have more errors to figure out before I can even measure the bed screws. Getting "pin needs to be specified in probe" no matter what config I have used. Been working on this for 3 days and my probe offset won't work correctly. Gotta love Klipper and random configs lol.

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      @@HiHoSilverAway76 what mainboard are you using?

    • @HiHoSilverAway76
      @HiHoSilverAway76 ปีที่แล้ว

      @@EtherealProject3D ATMega2560

    • @HiHoSilverAway76
      @HiHoSilverAway76 ปีที่แล้ว

      @@EtherealProject3D I was able to make another config file work. But testing bed mesh next. Probe is working/heaters/etc. I appreciate your help nonetheless and will come back to this video once my replacement parts come in for my SW-X2 (Arrived DOA but could get klipper to talk to it).

  • @dopestuff
    @dopestuff 4 หลายเดือนก่อน

    hey love the guide, but the "klipper configs" file is no longer in the google driver?

    • @EtherealProject3D
      @EtherealProject3D  4 หลายเดือนก่อน +1

      Its linked through my website now. If you have any trouble with it let me know.

  • @thomasb8247
    @thomasb8247 8 หลายเดือนก่อน

    Hello, my printer is a SWX2. the pc only recognized it in the device manager as a USB device under the name STM32 Bootloader. I can access it with STM32 but not with Pronterface(there i need a COM port and i dont have one offert). I have the Plantine version 1.2 and had to jump. Does anyone know what I did wrong?

  • @user-dz8rh4yx4p
    @user-dz8rh4yx4p 6 หลายเดือนก่อน

    super vidéos !! mais je n arrive pas à faire fonctionner le macros BED TRAM

  • @andyw8009
    @andyw8009 5 หลายเดือนก่อน

    Hi Matt, I am having a little issue and u might be able to help... I have klipperized my SWX2 thanks to you, I have upgraded bearings on my carriage (extruder) and now when I go to do BED TRAM it goes so close to the bed that when the CR touch probe drops it hits the bed (no gap in between). Nothing has changed apart from the bearings...what do I do now? Any ideas?

    • @EtherealProject3D
      @EtherealProject3D  5 หลายเดือนก่อน

      Is the nozzle hitting the bed? if so, adjust your zoffset.

    • @andyw8009
      @andyw8009 5 หลายเดือนก่อน

      ​​@@EtherealProject3D the nozzle was not touching the bed, just the probe hitting the bed during its initial drop. I think I have managed it though, lowered the bed down to make it a little bit further away from the probe and managed to carry out the Bed Tram as well as all other bed leveling operations 😊

    • @EtherealProject3D
      @EtherealProject3D  5 หลายเดือนก่อน +1

      @@andyw8009 Awesome, glad you got it sorted. Good luck and if you have any more questions please dont hesitate to ask.

  • @jvs126
    @jvs126 10 วันที่ผ่านมา +1

    Hi, I use orca slicer.
    I have followed all the steps and when I print the motors it loses steps, I think the error is in the accelerations, could you make a profile for orca slicer?
    I am using a translator, I don't know if it will be understood,
    Thank you very much in advance

  • @user-ps1yr9fc7l
    @user-ps1yr9fc7l 4 หลายเดือนก่อน

    Ok I am just using SM32 and Plugged into the USB only. However in SM32 the port shows as SWD and not USB, there are no options for the USB?

  • @MonsieurKero
    @MonsieurKero 10 หลายเดือนก่อน

    Thanks for your videos :D
    I have a problem with the "MCU"! I put it in the right place but it doesn't work and I get this error message :
    Option 'serial' in section 'mcu' must be specified
    Once the underlying issue is corrected, use the "RESTART"
    command to reload the config and restart the host software.
    Printer is halted
    What should I do ?

    • @EtherealProject3D
      @EtherealProject3D  10 หลายเดือนก่อน

      Make sure you uncomment the line as well.

  • @LeonardoGPate
    @LeonardoGPate ปีที่แล้ว

    I wonder if sidewinder x2 can be connected with MKS pi board in order to install klipper.

  • @lb8384
    @lb8384 11 หลายเดือนก่อน

    Could you create a tutorial for the X1/X2 with your custom extruder PCB? Or is it the same as this video? :)

  • @erosvizcaya7387
    @erosvizcaya7387 ปีที่แล้ว

    hello! does the printer.cfg file work for a genius pro? thanks for the video. It was very helpful to me!

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      You would need to change the build volume and bed screw coordinates and yes it will work.

  • @stephenmills5133
    @stephenmills5133 ปีที่แล้ว

    A issue ive found is the bl touch that comes with the x2 puts the machine into a reboot loop so it can not be flashed with klipper , you need to remove it put the z limit switch on or upgrade to a cr touch

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      Thats strange, thank you for the info.

    • @HiHoSilverAway76
      @HiHoSilverAway76 ปีที่แล้ว

      I just got my sidewinder x2 yesterday, could you explain what you did or have a link to setting that up? I have yet to run into the issue but would like to read about it or know just in case I run into this error.

  • @pray4fabe899
    @pray4fabe899 5 หลายเดือนก่อน

    Would you recommend crtouch or genuine bltouch for klipper upgrade?

    • @EtherealProject3D
      @EtherealProject3D  5 หลายเดือนก่อน

      I like the CR Touch better, its been less prone to uncommanded deployments

  • @leeo.alexander2324
    @leeo.alexander2324 ปีที่แล้ว

    I am assuming that this setup would work on an Artillery Sidewinder X1, correct. I have been interested in Klipper for awhile but I have not attempted to try installing it on my X1.

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว +1

      The printer.cfg will be a bit different as the X1 uses a different mainboard. There are some X1 configs out there that are a great starting point. The process will be close to the same though, the main difference is with the X1 you need to disconnect the tft and update the firmware with a slicer.

    • @leeo.alexander2324
      @leeo.alexander2324 ปีที่แล้ว +1

      Thanks. I have already installed a switch to turn the tft off when updates are required next to the "Reset" button. All I have to do now is collect the files and start the change. Thanks again.

  • @ascottilterribile
    @ascottilterribile 6 วันที่ผ่านมา

    Il file SWX2 _BL_Touch & 3D Touch
    Può essere usato per una stampante X1 con bl touch ?
    Grazie

  • @santini39
    @santini39 2 หลายเดือนก่อน

    Merci beaucoup pour cette vidéo, je l'es suivi pas a pas mais au moment d'imprimer j'ai ce message d'erreur "Unable to open file" et je ne trouve pas la solution?

  • @techrevolutions
    @techrevolutions 8 หลายเดือนก่อน

    was going great until the firmware was flashed as per the included options and my rpi just cannot detect the mcu in the , no port etc, tried a few different commands and its just not showing up as it did for you in the "Get mcu" section, any advice ?

    • @Prevettspecialdesign
      @Prevettspecialdesign 2 หลายเดือนก่อน

      Same problem for me too? Did you get it fixed?

  • @Batista99PT
    @Batista99PT 8 หลายเดือนก่อน

    We can use these configs on Artillery Sidewinder X2 using a Sonic Pad? Im new in 3d printing

    • @EtherealProject3D
      @EtherealProject3D  8 หลายเดือนก่อน

      Yes you can use them as a start but you will need to use the top portion of what Creality provides with the Sonic Pad documentation.

  • @gthestar
    @gthestar ปีที่แล้ว

    hi, noob question, can I follow this tutorial with a BIGTREETECH BTT Pi V1.2? I know they give an easy and direct way ton install klipper and mainsail on it but with your tutorial I would be able to flash the swX2 motherboard easily. thank you for your work, I'm not very confortable with all this but the way you explain it makes me feel able to do it.

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      Sort of, you will need to use tje BTT CB1 image as opposed to the pi os.

    • @gthestar
      @gthestar ปีที่แล้ว

      @@EtherealProject3D thank you, so I have to instal KIAUH the same way you did to compile the motherboard firmware after flashing the BTT image?

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      @@gthestar Yes, once you get the image installed you need to open the configuration file in the boot folder on the sd card and put in your wifi info. Then you can follow the guide

    • @gthestar
      @gthestar ปีที่แล้ว

      @@EtherealProject3D great!! thank you for your help, a lot!

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      @@gthestar No problem. I did a livestrem with the BTT PI last week and I go over this. I will finish in tomorrows stream.

  • @Dvm2003
    @Dvm2003 ปีที่แล้ว

    Does this video generally apply to the older x1?

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      You can use it as a general guide but flashing the mainboard will be a little different and the configs will be different.

  • @AnonUsername473
    @AnonUsername473 11 หลายเดือนก่อน +2

    Hi, i have a problem. After your installation something went wrong as from the pi the connection wasnt working. So i decided to restart from 0 but now i'm not able to connect the printer to the pc anymore. The pc detects the 3d printer in DFU mode as "unknown USB device", pronterface gives me "rubbish reply bad baudrate" error and STM32 doesn't recognise any USB or Serial port available. I'm in serious trouble help

    • @EtherealProject3D
      @EtherealProject3D  11 หลายเดือนก่อน

      That means klipper firmware is on the printer, continue on with the install on the pi.

    • @AnonUsername473
      @AnonUsername473 11 หลายเดือนก่อน

      @@EtherealProject3D Thank you for responding, fixed the problem and now i have klipper all set up! Only thing is that the turorial skips over how to install the screen on the raspberry (or i have just missed it), ty for the tutorial!

  • @eberger02
    @eberger02 4 หลายเดือนก่อน

    My comment seems to have disappeared, so apologies if this question appears twice in a row.
    If I’ve upgraded the hot end to all metal bits how does the printer configuration file need changing? I have no display. I guess it is just the maximum temperature but maybe there is something else?
    Oh, I forgot to mention that I have ordered one of your PCB breakout boards and a BL Touch Original, but I doubt either makes a huge difference.
    Just remembered I upgraded the thermistor (NTC 100k)

    • @EtherealProject3D
      @EtherealProject3D  4 หลายเดือนก่อน +1

      Just the max temp needs to be updated in the printer.cfg.

    • @eberger02
      @eberger02 4 หลายเดือนก่อน

      @@EtherealProject3Dthanks. That was my guess, but it’s nice to be sure.

    • @EtherealProject3D
      @EtherealProject3D  4 หลายเดือนก่อน

      @@eberger02 yeah yeah

  • @Timlicious89
    @Timlicious89 2 หลายเดือนก่อน

    love your tutorials, realy easy to follow and on point.
    but i have a problem with this one...
    im using a genius pro, so i changed the position_max values in [stepper_x/y/z] in the printer.cfg
    but it feels like it needs even more changes.
    homing isnt completly centered on the Y for example.
    and when i do the "bed tram" macro, the whole hotend getting squished into my bed so its stopping...
    hope someone can help me, i saw a lot getting this running on genius pro with your help but jeah... :/

    • @EtherealProject3D
      @EtherealProject3D  2 หลายเดือนก่อน +1

      you need to change the home coordinates

    • @Timlicious89
      @Timlicious89 2 หลายเดือนก่อน

      guess i found the spots which needed to be changed by myself now. hotend is centered nicely on my genius pro.
      will check later if there is also still the same problem when im going for the bed tram macro

    • @Timlicious89
      @Timlicious89 2 หลายเดือนก่อน

      "Bed Tram" dosnt realy work for me, the firmware thinks the screws are at the spot of the sidewinder. but i changed the screw spots (i took them from a genius pro printer.cfg i found)
      any solution for this? or may i have to change mor ein the printer cfg?

    • @Timlicious89
      @Timlicious89 2 หลายเดือนก่อน

      @@EtherealProject3D wasnt only the home coordinates which needed some love. but i think i found all coords which needed tweaking for the genius pro and so far its running nicely. realy appreciate your good work and content for the artillery printers.

  • @Leolikesbizkits
    @Leolikesbizkits 11 หลายเดือนก่อน

    I've installed this on my SW-X2 and seeing good results so far, still going through the calibration and fine tuning.
    Question: Could I use all the SW-X2 files and changes the Printer bed sizes so that it could be used on a Genius Pro?
    My Genius Pro is all ready for klipper, it has a config already but I'd like to use the same cfg and macros etc for the Genius
    Thank you for the X2 tutorial!

    • @EtherealProject3D
      @EtherealProject3D  11 หลายเดือนก่อน +1

      Yep you can do that for your gpro.

  • @undercavemen
    @undercavemen ปีที่แล้ว

    Hi, in your documentation your firmware upgrade says it goes upto 300º but the stock extruder is limited to 240º. Is this compatible with the stock extruder from the SX2?

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว +1

      You will need to change to an all metal hot end if you want to print hotter than 240.

    • @undercavemen
      @undercavemen ปีที่แล้ว

      @@EtherealProject3D Sorry to be such a pain. I am on MAC and now I am stuck in the part where you connect the printer for the 1st time to put the m997 command, I am getting the following error and would not like to continue since firmeware installation is sensible. This is the error: SENDING:M997
      Can't read from printer (disconnected?) (SerialException): read failed: [Errno 6] Device not configured

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว +1

      @@undercavemen this can happen, just continue on.

  • @ternocimadh5863
    @ternocimadh5863 2 หลายเดือนก่อน

    Can you make a beginnerstutorial for sw x3 pro

    • @EtherealProject3D
      @EtherealProject3D  2 หลายเดือนก่อน

      I would love to but I currently do not have that machine.

  • @omnizziah
    @omnizziah 5 หลายเดือนก่อน

    I can't put my machine to DFU mode. In pronterface I can connect to it (Serial USB device COM5) but as I enter M997, it drops "Can't read from printer" and "Can't write to printer" errors. If I put the jumper on the motherboard's pins, windows 11 losts connection to the printer, COM5 disappears and an unknown device appears in USB devices.
    Can someone help me step-by-step? Also it's not clear when exactly to put the jumper on the pins (During ON or OFF state? When to take it off precisely?) Although I think I tried all the combinations...

  • @dincerdilci4661
    @dincerdilci4661 4 หลายเดือนก่อน

    Hi... A report like this appears in Klipper reports. This is why Klipper Dashboard does not work. What should I do?

  • @theusuario-pb5xk
    @theusuario-pb5xk 6 หลายเดือนก่อน

    Hi
    I have modified all the scripts and code for a Genius Pro and it's working
    BUT i'm having a small problem when starting the print
    It gives me an error related to the temp, as the temp it's insufficient(below min) to draw the purge lines
    If i manually input the temp and after that i start the print it works

    • @EtherealProject3D
      @EtherealProject3D  6 หลายเดือนก่อน

      What slicer are you using? Sounds like a problem with you start macro/gcode.

    • @theusuario-pb5xk
      @theusuario-pb5xk 5 หลายเดือนก่อน

      @@EtherealProject3D i'm using prusaslicer
      and the exact error is : Extrude below minimum temp
      the initial gcode it's exactly as in your video
      PRINT_START
      SET_PRESSURE_ADVANCE ADVANCE=0.068
      I use 220ºc to the noozle and 65ºC on the bed
      When i send the file, the printer starts to heat up the bed until it reaches 65ºC
      After that it starts heating the noozle and at the same time it moves to the home position
      it start moving to draw the purge line but an error pops with that code, the noozle at that moment it's around 80ºc
      maybe a M109 it's missing on the code?
      /////////////////////////////////////////////////////////////////////////////////
      i think i fixed it changing the print_start macro to grab the temp from the slicer
      on printer.cfg
      [gcode_macro PRINT_START]
      gcode:
      {% set BED_TEMP = params.BED_TEMP|default(65)|float %}
      {% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(225)|float %}
      G90 ;Set to absolute positioning
      G28 ;Home all Axes
      M190 S{BED_TEMP} # Wait for bed to reach temperature
      M109 S{EXTRUDER_TEMP} # Set and wait for nozzle to reach temperature
      BED_MESH_PROFILE LOAD=default ;Load Bed Mesh Profile
      _PURGE_LINE ;Side Purge
      on prusa start gcode:
      PRINT_START EXTRUDER_TEMP=[first_layer_temperature] BED_TEMP=[first_layer_bed_temperature]
      SET_PRESSURE_ADVANCE ADVANCE=0.068

    • @EtherealProject3D
      @EtherealProject3D  5 หลายเดือนก่อน

      @@theusuario-pb5xk In Prusa slicer you need to add the heatup gcodes

  • @sambartling6787
    @sambartling6787 2 หลายเดือนก่อน

    I cannot get pronterface to connect. It says connected but when I m997 it says it cannot read from printer.

  • @bamboo9840
    @bamboo9840 7 หลายเดือนก่อน

    After the step with pronterface and SMTprogrammer I'm unable to communicate with the x2 anymore. I've tried to flash the stock firmware via SD and even this hasn't resolved my issue... Do you know how I could fix it? Thank you in advance

    • @bamboo9840
      @bamboo9840 7 หลายเดือนก่อน

      After reading a few comments I have to clearify that the MCU I've used doesn't really gets accepted from Mainsail. I'm always getting the MCU-Error

  • @stephenmills5133
    @stephenmills5133 ปีที่แล้ว

    So i managed to get klipper to work with stock X2 and how i done it was disconnected the bl touch connected mainsail done the config of the mcu then reconnected the bl touch and now ive sorted most of the configs

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว

      Awesome, im glad it worked out for ya.

    • @stephenmills5133
      @stephenmills5133 ปีที่แล้ว

      @Ethereal Project 3D ive just done the map , going ginosh the set up tomorrow and sort a cura profile out for it
      Thats a question i wanted to ask you , have you got a profile for the sovol sv06 plus for cura or prusaslicer

    • @EtherealProject3D
      @EtherealProject3D  ปีที่แล้ว +1

      I do not, sorry.

  • @muhammetburakcevik9387
    @muhammetburakcevik9387 7 หลายเดือนก่อน

    First of all, thank you very much for your information, but I have a problem, can you help me? I cannot install a stm32 cube programmer on my computer. Step 7 remains on a white screen. Do you know why?

    • @EtherealProject3D
      @EtherealProject3D  7 หลายเดือนก่อน

      Try running the exe as admin.

    • @muhammetburakcevik9387
      @muhammetburakcevik9387 7 หลายเดือนก่อน

      @@EtherealProject3D I tried but it didn't work 😥

  • @dixmitty
    @dixmitty ปีที่แล้ว

    Does anyone have Klipper installed on a rpi that already has Homebridge (home automation software)?

  • @user-ps1yr9fc7l
    @user-ps1yr9fc7l 4 หลายเดือนก่อน

    At the point where you enter the M997 code I am getting a Error 13 and I am not able to continue with the install. Any suggestions appreciated.

    • @EtherealProject3D
      @EtherealProject3D  4 หลายเดือนก่อน

      You will have to put it in DFU mode manually, on the mainboard there is a cluster of pins. With the power off and USB disconnected, jump the pins labeled 3.3v and boot. then connect only USB power, no main power. then continue on witht e update from STM32. When done, remove USB power and then the jumper.

  •  8 หลายเดือนก่อน

    Question : 1 month ago upgraded my X2 to klipper as i commented. Notice new version os klipper are out and require to upgrade the printer firmware ? i know how to generate a new version of the firmware , but how to flash it ? pronterface ? or on klipper server ? Thanks

    • @EtherealProject3D
      @EtherealProject3D  8 หลายเดือนก่อน +1

      You will need to put the printer in DFU mode manually by jumping the boot and 3.3v pins on the mainboard , power with usb only then upload new firmware using stm32 programmer

    •  8 หลายเดือนก่อน

      @@EtherealProject3D ahhh so , pronterface M997 will not work anymore ? probably i will stick to this versions for a while, until a major version is released or something.

    • @EtherealProject3D
      @EtherealProject3D  8 หลายเดือนก่อน

      @No pronterface will not work. Thats a Marlin thing.

    •  8 หลายเดือนก่อน

      @@EtherealProject3D ahhh i suspected that. Ok got it ! Thank you so much! Cheers

  • @FrostNuke
    @FrostNuke 11 หลายเดือนก่อน

    do you have clipper file for the x1? or is it the same as the x2?

    • @EtherealProject3D
      @EtherealProject3D  11 หลายเดือนก่อน +1

      Its a different file. I think I have one hanging out someware.

  • @Blejzzz
    @Blejzzz 3 หลายเดือนก่อน

    Do I need Marlin installed on my printer or can I instal Klipper on stock machine?

    • @EtherealProject3D
      @EtherealProject3D  3 หลายเดือนก่อน

      The machine has marlin stock, but yes you can install klipper on the stock machine

    • @Blejzzz
      @Blejzzz 3 หลายเดือนก่อน +1

      @@EtherealProject3D thank you for your help

  • @graftechkrakow5995
    @graftechkrakow5995 หลายเดือนก่อน

    Hi
    I'm trying to install Klipper and everything was going well until the printer connected using Pronterface. The printer had a connected status, but the m997 did not work, errors appeared and the message "the fourth unsuccessful attempt will disconnect the printer" from now on it is impossible to connect to the printer. Stm32 also does not detect the printer. Do you have any advice on how to fix this.

    • @EtherealProject3D
      @EtherealProject3D  หลายเดือนก่อน

      You will need to put it into dfu mode manually by jumping the boot and 3.3v pins on the mainboard then powering it via USB

    • @graftechkrakow5995
      @graftechkrakow5995 หลายเดือนก่อน

      @@EtherealProject3D Unfortunately, the attempt to upload the firmware failed, I get the message "Error: Data mismatch found at address 0x08000004 (byte = 0x05 instead of 0x75)
      Error: Download verification failed)
      the jumper on the board is set to boot + 3.3v, STM32 has a connected status. Artillery Ruby motherboard version V1.2, TFT version GD32F305
      I have no idea what to do next