Great build You need the silencer stock or amazon for $24. And that motor will do 60 and come on the pipe harder. Needs back pressure. I've raced 80s 250s and 500s for 30 years
Your front forks are back-to-front. Loosen your handle bars, disconnect cables etc to the front brakes, rotate your forks 180deg then tighten your handlebars and reattach your brake cables.
I don't know if you remember me, but I met you in a game called badeggs and you told me to subscribe to your channel and I did ... and I liked your content, I was practically one of your first subscribers and I hope you have more
Nice Ripper! If you take a bit of 1-1/8" diameter tubing to your pipe,then pinched down to 7/8 to the flange on a smoother transition it will increase the sonic wave effect at low to mid rpm. You can still bolt that way That little step you have is costing you a bit of the sonic pressure wave, by about 20-30%. Try not to dent the expansion chamber each dent disrupts the wave 👍
I can not get my bike to idle I adjusted the screw in every position 1/8 inch in every direction adjusted the clutch. Still dies when clutch disposables
Push if you don't want to damage the clutch. Due to the way the clutches work on these engines, they're basically either engaged or disengaged, not really any in-between, so if you engage the clutch at 0mph the engine will bog and die almost instantly, unless you dump the clutch at high revs, which is very likely to break the clutch or snap something. So tldr: must be moving a bit first
You're kidding right? The RIGHT pipe and jetting can add upwards of 3hp to these little engines, that and ethanol-free gas (I run AvGas in mine) and gearing it's not at all impossible to have a 60MPH plus bicycle. Running AvGas (Aviation Fuel, available at your nearest airport) alone would add 2 or 3hp. Key to these little 2 strokes is the highest octane gas you can get without alcohol in it, Bestways and 7/11s have ehanol-free fuel, at least around here anyway. The beauty of these 'lil Chinese engines is there's so much room for improvement, and you can go high-dollar, or you can go low-buck, and still get measurable performance out of them. My Zeda's bone stock and with pump gas it'll do 40MPH all day long, and I weigh about 280#. Running Avgas brought that up to just a tad under 50 on the flat, and again, that's a stock engine.
@@randomprecisionmotors3130 Ya my bike a sled now I lost the needle clip leaning it out on my oko carb had to put the nt carb on got to pull the jug and port it and buy a vm18 this time doing only 39 mph with reeds...Not to happy with the yd100
I gotta tell ya though, the more I mess with this supposed 'HP' carb, the more I wanna just slap the NT carb back on...didn't have to mess with that NEARLY as much as the HP, I had a HELL of a time getting it to idle with the HP, and finally after a combination of cable adjustment idle screw adjustment it idles, although a bit high for my liking...
@@macmotorizedbike3834 Really? YD100's going on my next build, probably a 20" rig if I can find the right frame. Probably keep that all stock as well except jetting will go down from a #70 to a #66, and probably a KX65 pipe or am OLD YZ80 pipe. Expansion chambers are the ticket for these motors, but you don't want one with too big a chamber, and one of those older YZ pipes would be ideal if I could find one...
@@randomprecisionmotors3130 Ya hp sucks big time. Nt better I was using oko much better than both like night and day treatland sells needles thank God pack of 10 18 bucks
i love that sound!! is it good to buy performance parts from aliexpress? Found out that aliexpress parts are good and some of them are sold twice the price in bikeberry and gasbike
Hi does your manifold pipe that you made make less of a responsive throttle ? I’m wanting to do the exact same as you but love how responsive the throttle is with the stubby manifold I have. Is there a difference ? Thanks 😊
We used a carb laying around for my old yamaha dt175 enduro 2 stroke my dad modified it on my YD100 she was wicked my current bike is 88cc she's surprisingly faster than the 100 don't ask me why I haven't tried a top speed run I know I backed off at 55 60 with way more throttle going
I will purchase that engine for a project during summer ,i wanted to ask you if you know how to make it sound less loud because i live in the center of athens and noise can get me in trouble with the authorities and the neighbors.Thank you in advance
Dude at the heck of a bike you did a real nice job on it what kind of motor is that you got to see you at tell me what kind can you use on that please my email AdamDemel@gmail.com
If some one will know how to operate the clutch they can easily steal the machine by pedaling it. Why not eliminate the problem of theft all together by removing the pedals. It is also better to bump start these engines then it is to pedal start the machines. They are all reverse thread machines
They do sell pull starts, I've had one before, if you want to see it in action check out my first start up on my motorbike video, but it's Chinese you know and it broke on me and I didn't bother buying another one.
If you would have taken the jet from the stock carb and put it in that newer carb you bought it would have ran beautifully, thats what i did. You need to force it a little but it’ll go
Do you recall what size jets you ran and what size is the carb? I'm running a PKW21 and I'm up to 150 on the main jet and 38 on the air jet with very poor results.
Great bike that sounds as I expected it real raw and fast I know for a much lighter frame such as a bicycle lol scoot took a new state called VROOM! Who did your custom exhaust work to give it an adaptable flange to mount on that block? I weld some and ask for ideas and materials that Id try experiments with. Thanks mate keep your brakes fresh lol that thing is swift & really smokes em.
Hey, Ive got the same motor on my bike, and I just happened to have a 28mm mikuni flat slide carb almost identical to yours in the video, just sitting in my shop. What jets sizes and needle clip position are you running? I just installed mine along with a suzuki pipe and I'm not getting enough fuel for the engine to run without the choke on. It will start easily with the choke on but bogs with the throttle and dies the second the choke is turned off
A 28mm is pretty much too big for any of these motorized bikes, a vm18 would be a much better match. I'm running a 22.5 pilot and 67.5 main in mine but it'll be different for elevation and so on
Lol dude that thing is sick, I just crashed my suzuki bandit 1200 a couple weeks ago and was thinking of building me one of these go get my riding fix instead of buying a new bike. How much does something that quick cost to build ?
My Andbull 80cc gets 56mph with what mods Ive done But I have yet to venture to the dark side of Suzuki parts re purposed for fastest bicycle power where adding an engine not far from the benchmark even if a China doll it can be rebuilt its ALIVE! Muaha hahaha
Yes the stock is the quietest but I daily drove it to work every, single, day there and back rain or shine for about 6 months until I bought the Mustang😁 which is now with a full exhuast and is pretty damn loud and I daily drive it everyday😂 im just a loud type of guy I guess lol🤷♂️
Great build You need the silencer stock or amazon for $24. And that motor will do 60 and come on the pipe harder. Needs back pressure. I've raced 80s 250s and 500s for 30 years
Your front forks are back-to-front. Loosen your handle bars, disconnect cables etc to the front brakes, rotate your forks 180deg then tighten your handlebars and reattach your brake cables.
Whole thing looks back to front lol
I don't know if you remember me, but I met you in a game called badeggs and you told me to subscribe to your channel and I did ... and I liked your content, I was practically one of your first subscribers and I hope you have more
Oh yes I remember 😂, but thank you so much for staying!
Nice Ripper!
If you take a bit of 1-1/8" diameter tubing to your pipe,then pinched down to 7/8 to the flange on a smoother transition it will increase the sonic wave effect at low to mid rpm. You can still bolt that way
That little step you have is costing you a bit of the sonic pressure wave, by about 20-30%.
Try not to dent the expansion chamber each dent disrupts the wave 👍
You should put a good set of racing reeds with a stuffer kit in the reed cage I bet you wake it up and would sound even more amazing
What gas tank is that as well
These and Beater Cars are bae
Thank you! A pull start! Don't understand why people wont install a 25 buck part thats so convenient!!
Ive had a pull start before, it broke and didn't bother buying another one #china 😂
Because the pull starts iv seen are junk,,iv got one I'm gone send back
Besides the pull start being junk it widens the engine blocking your stock cranks from pedaling.and custom cranks feel unnatural.
What type of bike is it?
I can not get my bike to idle I adjusted the screw in every position 1/8 inch in every direction adjusted the clutch. Still dies when clutch disposables
Crazy biker. 👍
Cool build bro
Thnx
Welcome
How come u dont make motorized bicycle vids anymore
Hey man you got a link to that hose for some reason I can’t find one for my Oko anywherw
If you come to a stop, do you have to push off the ground before going or can you start from a dead stop?
Push if you don't want to damage the clutch. Due to the way the clutches work on these engines, they're basically either engaged or disengaged, not really any in-between, so if you engage the clutch at 0mph the engine will bog and die almost instantly, unless you dump the clutch at high revs, which is very likely to break the clutch or snap something.
So tldr: must be moving a bit first
@@charliesmith874 too late, I got a cent clutch
Sweet nice speed without reeds never really thought a pipe made that much difference..Im running that BS zeda66 pipe
You're kidding right? The RIGHT pipe and jetting can add upwards of 3hp to these little engines, that and ethanol-free gas (I run AvGas in mine) and gearing it's not at all impossible to have a 60MPH plus bicycle. Running AvGas (Aviation Fuel, available at your nearest airport) alone would add 2 or 3hp. Key to these little 2 strokes is the highest octane gas you can get without alcohol in it, Bestways and 7/11s have ehanol-free fuel, at least around here anyway. The beauty of these 'lil Chinese engines is there's so much room for improvement, and you can go high-dollar, or you can go low-buck, and still get measurable performance out of them. My Zeda's bone stock and with pump gas it'll do 40MPH all day long, and I weigh about 280#. Running Avgas brought that up to just a tad under 50 on the flat, and again, that's a stock engine.
@@randomprecisionmotors3130 Ya my bike a sled now I lost the needle clip leaning it out on my oko carb had to put the nt carb on got to pull the jug and port it and buy a vm18 this time doing only 39 mph with reeds...Not to happy with the yd100
I gotta tell ya though, the more I mess with this supposed 'HP' carb, the more I wanna just slap the NT carb back on...didn't have to mess with that NEARLY as much as the HP, I had a HELL of a time getting it to idle with the HP, and finally after a combination of cable adjustment idle screw adjustment it idles, although a bit high for my liking...
@@macmotorizedbike3834 Really? YD100's going on my next build, probably a 20" rig if I can find the right frame. Probably keep that all stock as well except jetting will go down from a #70 to a #66, and probably a KX65 pipe or am OLD YZ80 pipe. Expansion chambers are the ticket for these motors, but you don't want one with too big a chamber, and one of those older YZ pipes would be ideal if I could find one...
@@randomprecisionmotors3130 Ya hp sucks big time. Nt better I was using oko much better than both like night and day treatland sells needles thank God pack of 10 18 bucks
Why'd you remove the pedals? If you're going to do that you might as well get a pull starter or electric ignition.
What kind of carburetor is this and where can I get it ??
I have a 32 tooth sprocket and when I hit 40mph my eyes water so bad it's hard to see
Does this fits on a pitbike
i love that sound!! is it good to buy performance parts from aliexpress?
Found out that aliexpress parts are good and some of them are sold twice the price in bikeberry and gasbike
I dont buy from cheap sites like aliexpress and wish lol, I dont care how well the things in their are made I just don't trust it.
@@dreygrach i noticed that the parts on aliexpress for motorized bike are the same that you can buy in bb or gas bikes
Good thing I bought the same carb that u have on.
Hi does your manifold pipe that you made make less of a responsive throttle ? I’m wanting to do the exact same as you but love how responsive the throttle is with the stubby manifold I have. Is there a difference ? Thanks 😊
What bike and motor is that? Looks sick man
Kids 20 inch bike, Amazon/eBay 66/80cc motor that I built myself.
We used a carb laying around for my old yamaha dt175 enduro 2 stroke my dad modified it on my YD100 she was wicked my current bike is 88cc she's surprisingly faster than the 100 don't ask me why I haven't tried a top speed run I know I backed off at 55 60 with way more throttle going
Isn't it because the yd100 80cc?
I will purchase that engine for a project during summer ,i wanted to ask you if you know how to make it sound less loud because i live in the center of athens and noise can get me in trouble with the authorities and the neighbors.Thank you in advance
If you buy the whole kit it comes with a really quiet exhaust, mine is after market thats why its so loud.
@@dreygrach ohh I thought it was very loud because they sound loud in most videos I have seen, thank you tho I feel more confident on buying one now ✌
@@wakaka9168 yep, no problem.
I'd say you did a great job ,,,I want that pipe an carb so bad, ,,that engines is ripping it's ass off ,,,
Haha yuup, and thanks!
Hey so I have one of these bikes to and is there a way to get the carb to go onto the original intake with out no rubber hose
Hmmm not sure maybe play around and find out.
Dude at the heck of a bike you did a real nice job on it what kind of motor is that you got to see you at tell me what kind can you use on that please my email AdamDemel@gmail.com
Why did you remove the pedals????
Not enough room or to prevent theft. That's what I do with mine. Pedals clank the exhaust
If some one will know how to operate the clutch they can easily steal the machine by pedaling it. Why not eliminate the problem of theft all together by removing the pedals. It is also better to bump start these engines then it is to pedal start the machines. They are all reverse thread machines
When is somebody going to come up with a pull start for these little motors there are lots of things we could do with them if we had a pull start
They do sell pull starts, I've had one before, if you want to see it in action check out my first start up on my motorbike video, but it's Chinese you know and it broke on me and I didn't bother buying another one.
Hard to place pull starters..most will hit your pedals
If you would have taken the jet from the stock carb and put it in that newer carb you bought it would have ran beautifully, thats what i did. You need to force it a little but it’ll go
Oh really, maybe I'll try that.
Do you recall what size jets you ran and what size is the carb? I'm running a PKW21 and I'm up to 150 on the main jet and 38 on the air jet with very poor results.
You’re Going the wrong way, smaller jet sizes needed for peak performance but not too lean
This video, this bike, this is one of those that got me here. You alive bro?
Damn yeah man I'm still here, I've been having so many things to deal with, I really do want to get back tho
@@dreygrach Good to hear that. Better a busy body than an idle one. Stay strong.
Great bike
that sounds as I expected it
real raw and fast I know for a much lighter frame such as a bicycle
lol
scoot took a new state called VROOM!
Who did your custom exhaust work to give it an adaptable flange to mount on that block?
I weld some and ask for ideas and materials that Id try experiments with.
Thanks mate
keep your brakes fresh lol
that thing is swift & really smokes em.
Hey, Ive got the same motor on my bike, and I just happened to have a 28mm mikuni flat slide carb almost identical to yours in the video, just sitting in my shop. What jets sizes and needle clip position are you running? I just installed mine along with a suzuki pipe and I'm not getting enough fuel for the engine to run without the choke on. It will start easily with the choke on but bogs with the throttle and dies the second the choke is turned off
Hmmm I'm not sure, I had a buddie jet it for me, not sure about the needle clip also, whenever I take it apart I'll look at both.
A 28mm is pretty much too big for any of these motorized bikes, a vm18 would be a much better match. I'm running a 22.5 pilot and 67.5 main in mine but it'll be different for elevation and so on
What jet u run un that carb
Sorry I don't remember :(
😮😮
Lol dude that thing is sick, I just crashed my suzuki bandit 1200 a couple weeks ago and was thinking of building me one of these go get my riding fix instead of buying a new bike. How much does something that quick cost to build ?
200$
@@lukeriley2721 $200 is like the cheapest build you can get lol
Well my build cost around 600 dollars, I got a while videonon how much I payed for every part and how much the whole build came out in total.
What is the top speed
Its in the video.
45mph
I missed this bike.
45 miles? Dude, thats insane
Though the vid your bike sounds exactly like mine. I have a clone wc80 pipe standard nt speed carb and it sounds like a ktm65
Cool
Yep thanks!
You should get a jackshaft for it
Jackshaft for....gears?
Yes
It uses the stock bike gears
@@liamsmith5976 yeah We will see, because thats quite some work, since I have no gears only one drive gear.
You just need a pull start now
I had a pull start on it before, but it broke and I didn't bother buying a new one.
Mine hits 40mph
Nice
Your pipe header is way to small I use 1 /14 header tubing get rid of that stock header on that nice pipe
Look up (pipe it up) on Ebay he sales headers
👍👍
My Andbull 80cc
gets 56mph with what mods Ive done
But I have yet to venture
to the dark side of Suzuki parts re purposed for fastest bicycle power where adding an engine not far from the benchmark
even if a China doll
it can be rebuilt
its ALIVE! Muaha hahaha
Yo nice bike but your forks are on wrong.
For like the hundred time I'm being told😂, its on back wards unporpose. Check out my full reviews of my bike for an explanation why.
And thanks.
Just put a moped pipe
Naw bud the smaller the tires the faster it will go
Stock pipe is the quietest. These bikes are way too loud for daily use.
Yes the stock is the quietest but I daily drove it to work every, single, day there and back rain or shine for about 6 months until I bought the Mustang😁 which is now with a full exhuast and is pretty damn loud and I daily drive it everyday😂 im just a loud type of guy I guess lol🤷♂️
DreyGrach Aussie? Or Uk?
@@st.paulmn9159 Wait are you asking if I'm Ukrainian? No I'm Russian. Sorry I dont quite understand your question.
I daily ride wit a mz65 yd109 it’s loud af but that’s most the fun!!
This is why i read the comments 💯 uk 🇬🇧 Ukraine 🇺🇦 practically the same thing 😑