It doesn't work. Version 17 of capwap is out and after running the first stage to update the lightweight version with the mobility-express command, it actually bricks the primary boot image.. It installs it as a mobility-express but in reality it's a the lightweight image. Then if you try to convert it, it only shows the option ap-type capwap....
Windows firewall was blocking tftp traffic... (i assumed the network where the AP sits was considered a private network; it was public). Thanks for the video
Hi Sal, I follow through the steps, all went fine until the image update I hit into some issue saying ....... Image downloaded, writing to flash... do CHECK_ME, part1 is active part tar: can't open '/tmp/part.tar': No such file or directory No part.tar found Error: Image update failed. AP3820.567E.03C8# Writing reload timestamp (Sat Apr 11 15:42:54 UTC 2020) to disk [04/11/2020 15:42:55.2752] UBIFS: un-mount UBI device 0, volume 3 [04/11/2020 15:42:57.3746] Restarting system. [04/11/2020 15:42:57.4046] Going down for restart now Please help
Thanks for the video & as your videos instruction, i have already converted AP from capwap to mobility express. but facing some problem to setup mobility. Our AP can boot by part1 & also part2 & during working in cli it is going to stop mode & start again. So, how would we overcome the problem & can set an static IP & which procedure should i follow to run mobility express properly?
Nice video. I followed it and converted an 1815i AP from CAPWAP to mobility express. However, the 5GHz radio remains disabled. Can you guide how to activate it?
Thank you for this. I know its like 6 years ago but still much help. I have a question regarding the error. Is it possible to erase the Flash before the installation? Do you think that would help? If yes, could you provide the code to format the flash? much appreciated.
I was able to convert my 3802 to mobility express. I can’t seem to tftp the ap file to have the ap’s join the controller. It is saying file not found. Pulling whatever little hair have out
I've tried this once before without success and back at it again. According to cisco documentation, the running version must be 8.3.102.0 or greater. I have 8.3.143.0 currently, and I get the disk space error. I don't have the entitlement for the capwap image and no longer have access to the WLC to upgrade that way. It's funny, I have entitlement for the ME code, but not the lwap code. Cisco isn't what it used to be.
@@CiscoSal I have never kept smartnet on the APs, but I do still have it on the controller. I used to be able to get code for the APs. I'm assuming I had that via the controller's contract, but not sure why that changed.
Is the reverse easily doable: converting AIR-AP3802P-B-K9C to AIR-AP3802P-B-K9? I'm not technical, so forgive me if this should be obvious from the discussion. Any reverse instructions appreciated.
I see on the Cisco site one of the files for the conversion is: AIR-AP3800-K9-ME-8-3-130-0.tar your instruction referenced "103.tar". Was your reference a typo or is Cisco's file just newer than what you used to produce the video?
+robb kinnin you are just looking at a different version of code. You are referencing a little older of a code 8.3. I was using 8.5. Thanks for watching!
If I have 1815I-Q-K9 (none - K9C) can I convert and use one of those as a wireless controller and the rest will be regular APs that will connect to Mobility Express WLC?
Hello excuse me when I enter the static ip in wired0, the status appears down protocol up and speed n / a the test of ping to the tftp server appears to me 0/5 could you help me, I would thank you very much please
I use them in my house exclusively. I will say I recently received some Meraki GO equipment and it is a lot more user friendly. It has some good features like being able to throttle specific traffic and block domains. Ill be doing a review on them shortly. You can buy these devices on Amazon sold by Cisco. So since its legit, you also get full support. Here is a link to the Amazon store amzn.to/3FqHWXY You do not need to purchase licenses or smartnet or anything like that. There is an optional security license that basically connects the Meraki GO firewall to the Umbrella Security Cloud, for more in-depth security. Way above what linksys, netgeaer etc will do. But if its for your home you probably don't need it.
@@CiscoSal Thanks for the C-Go recommendation!! I did a review of them a few revisions ago.. I am still waiting on the team to fill a few requests for me before I jump back on that ship. I am happy to see they introduced the web UI a month or so ago. I do have a question about the guest portal setup.. How is it on the ME platform I "think" you are able to change the background pages within the portal but wanted to make sure, and the 240AC doesn't allow this.
I have a Cisco 2802i CAPWAP AP with software version 8.3. If want to convert this to ME version 8.10, can I migrate directly to 8.10 from 8.3 or do I need to do incremental upgrade, like 8.3 to 8.5, 8.5 to 8.8 and then 8.8 to 8.10?
Hola. tengo "Aironet 2800i Access Point" no puedo descargar el software hagame el favor de bajarme y subir a mega porfavor.. les agradeceria muchisimo.
Try this www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/82/user_guide/b_ME_User_Guide_82/appendix.html#topic_A575EE4B2A054DE5BAF1931A7D384DB5
Hi Cisco Sal did you preforemed the conversion befor setting the AP up , i have 1800 series that won't let me Type anything in the CLI it just keep looking for a CAPWAP server then it reboot itself after 15 attempt !!
Cisco Sal Yes it is geeting enough power from Thr POE , i accessed to it via console and it says CAPWAP state : discovering looks like i need a wireless controlled to set it up then i can convert to Mobility express ?!
@@CiscoSal I'm having the same issue now. Without a controller on the network, it's stuck in a boot loop because of repeated CAPWAP discovery failure. Any idea how we can handle this?
Hi, you should be able to find that info here www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/82/user_guide/b_ME_User_Guide_82/appendix.html
Thanks! Just to confirm, you require a K9C versus a K9 PID to convert a ME to CAPWAP and vice versa. But AIR-AP3802i-B-K9 (US PID) only with CAPWAP cannot covert to ME correct?
The ones I used were AIR-AP3802i-B-K9. So, yes these can be converted to ME. The difference is from an ordering perspective the K9C ones you can select to have the ME code on them from the factory. The k9 ones there is no option to select ME code at the time of ordering. So, if you get the AIR-AP3802i-B-K9 they will have to be converted, or you use them in CAPWAP mode.
for some reason I can't get to the ME through GUI. I just connected the 3800 to my laptop and did the upgrade. I should be ablle to access the ME on my laptop correct? 10.0.0.2...any suggestions?
You can download the software from cisco.com. You can also purchase them with the ME software already loaded. I recommend talking to your partner to make sure they are selling you the correct version. If not they will probably default to the version that joins controllers.
@@CiscoSal cisco requied an account that subscribe to them to download the image. Meanwhilr i dont have that account. So if u have the image could you kindly mail it to me , will be very appreciate that
If you purchased the AP though cisco sanctioned channels then you can sign up for a cisco.com account and download the software. That’s how cisco protects themselves from unauthorized resellers.
At the time of perches product , you should pay for technical support they provide you all software reading our product as well as they as SR NO of product and they will be help you
I Need help , can you Help me sir , i have Ap modal no Air Ap 2802i-D-K9 , and i don't have controller but and want to convert 1 Ap as master Ap how i do ? you have iso file then provide me
After a day of searching online on how to do this, I stumbled across it on TH-cam.
Thank you
Thank you for your help, i followed throughout and it exceptional.
This has been tremendously helpful.
THANKS MAN!!! YOUR VIDEO IS SO USEFUL. I HOPE YOUR CONTINUES DOING MORE OF THIS
Thanks, converted a 1832i to ME
I'm trying to do the same but can't get the tar as I'm not a registered business. Can you help?
hey, can you send me a firmware 1832i ?
I had to reimage to lwap and it worked fine. Thanks Sal!
God bless you my friend, thank you very much
Thanks a lot ... to me it was a very useful tutorial ... it worked with AP2082i
It doesn't work. Version 17 of capwap is out and after running the first stage to update the lightweight version with the mobility-express command, it actually bricks the primary boot image.. It installs it as a mobility-express but in reality it's a the lightweight image. Then if you try to convert it, it only shows the option ap-type capwap....
Did you ever do the follow-up videos on getting the APs set up and tied together?
Windows firewall was blocking tftp traffic... (i assumed the network where the AP sits was considered a private network; it was public). Thanks for the video
Thank you so much Sir. It really helped me a lot. Thanks million !!!
Hi Sal,
I follow through the steps, all went fine until the image update I hit into some issue saying .......
Image downloaded, writing to flash...
do CHECK_ME, part1 is active part
tar: can't open '/tmp/part.tar': No such file or directory
No part.tar found
Error: Image update failed.
AP3820.567E.03C8#
Writing reload timestamp (Sat Apr 11 15:42:54 UTC 2020) to disk
[04/11/2020 15:42:55.2752] UBIFS: un-mount UBI device 0, volume 3
[04/11/2020 15:42:57.3746] Restarting system.
[04/11/2020 15:42:57.4046] Going down for restart now
Please help
Nice but you're taking a lot of shortcuts ! How to setup the tftp server, ho to connect the AP to the laptop, etc. I don't have a controller.
I get an error at the end: image upgrade not needed, changing AP Type to Mobility Express. What would I have to do?
Thanks for the video & as your videos instruction, i have already converted AP from capwap to mobility express. but facing some problem to setup mobility. Our AP can boot by part1 & also part2 & during working in cli it is going to stop mode & start again. So, how would we overcome the problem & can set an static IP & which procedure should i follow to run mobility express properly?
Nice video. I followed it and converted an 1815i AP from CAPWAP to mobility express. However, the 5GHz radio remains disabled. Can you guide how to activate it?
Thank you for this. I know its like 6 years ago but still much help. I have a question regarding the error. Is it possible to erase the Flash before the installation? Do you think that would help? If yes, could you provide the code to format the flash? much appreciated.
do you have ap3g3-k9w8-tar.153-3.JC1.tar for the 2802I? I Tried downloading it but i need a service contract to do so.
same
very timely video. What TFTP Server do you use?
TFTPD32 or TFTPD64 depending on the old laptop I'm using.
I was able to convert my 3802 to mobility express. I can’t seem to tftp the ap file to have the ap’s join the controller. It is saying file not found. Pulling whatever little hair have out
I've tried this once before without success and back at it again. According to cisco documentation, the running version must be 8.3.102.0 or greater. I have 8.3.143.0 currently, and I get the disk space error. I don't have the entitlement for the capwap image and no longer have access to the WLC to upgrade that way. It's funny, I have entitlement for the ME code, but not the lwap code. Cisco isn't what it used to be.
Do you have smartnet? Nothing has changed. Smartnet is still required for code upgrades and support on APs
@@CiscoSal I have never kept smartnet on the APs, but I do still have it on the controller. I used to be able to get code for the APs. I'm assuming I had that via the controller's contract, but not sure why that changed.
How do you find the ip for the TFTP server?
You need to make a tftp server on a laptop or something. Then its just the IP address of the laptop
Good. I do some convert and setting access point on my channel too.
AIR-AP2802I-E-K9 can I convert it nobility express
You can!
Is the reverse easily doable: converting AIR-AP3802P-B-K9C to AIR-AP3802P-B-K9? I'm not technical, so forgive me if this should be obvious from the discussion. Any reverse instructions appreciated.
So after going through this process do i go thru ur convert to autonomous mode video pr does mobility express make it autonomous?
Yes
@Cisco Sal
When you convert an AP into ME, does it still function as an AP, as well as an express-controller same time?
Yes it does
@Cisco Sal, if i have 13 device AIR AP and than i have one firmware , Probelm or No Problem ?
I see on the Cisco site one of the files for the conversion is: AIR-AP3800-K9-ME-8-3-130-0.tar your instruction referenced "103.tar". Was your reference a typo or is Cisco's file just newer than what you used to produce the video?
+robb kinnin you are just looking at a different version of code. You are referencing a little older of a code 8.3. I was using 8.5.
Thanks for watching!
hi where did you get the 10.0.0.1 IP?
thanks
It's IP address of your default gateway
hi , I have cisco access point Air 1832i , when mobility express downloading ,the access point start reboot . how can I fix that ?
Why is it rebooting?
@@CiscoSal I don't know , I just want avoid the reboot so I can upgrade the capwap
Try these two commands.
Debug LWAPP client no-reload
debug capwap cli no-reload
@@CiscoSal I will , thanks for your reply
@@CiscoSal these commands are not available in the CLI, any advice?
If I have 1815I-Q-K9 (none - K9C) can I convert and use one of those as a wireless controller and the rest will be regular APs that will connect to Mobility Express WLC?
Hello excuse me
when I enter the static ip in wired0, the status appears down protocol up and speed n / a
the test of ping to the tftp server appears to me 0/5
could you help me, I would thank you very much please
Has anyone used these APs in your home labs or home and if so how are they?
I use them in my house exclusively. I will say I recently received some Meraki GO equipment and it is a lot more user friendly. It has some good features like being able to throttle specific traffic and block domains. Ill be doing a review on them shortly. You can buy these devices on Amazon sold by Cisco. So since its legit, you also get full support. Here is a link to the Amazon store amzn.to/3FqHWXY You do not need to purchase licenses or smartnet or anything like that. There is an optional security license that basically connects the Meraki GO firewall to the Umbrella Security Cloud, for more in-depth security. Way above what linksys, netgeaer etc will do. But if its for your home you probably don't need it.
@@CiscoSal Thanks for the C-Go recommendation!! I did a review of them a few revisions ago.. I am still waiting on the team to fill a few requests for me before I jump back on that ship. I am happy to see they introduced the web UI a month or so ago. I do have a question about the guest portal setup.. How is it on the ME platform I "think" you are able to change the background pages within the portal but wanted to make sure, and the 240AC doesn't allow this.
I have a Cisco 2802i CAPWAP AP with software version 8.3. If want to convert this to ME version 8.10, can I migrate directly to 8.10 from 8.3 or do I need to do incremental upgrade, like 8.3 to 8.5, 8.5 to 8.8 and then 8.8 to 8.10?
Hola. tengo "Aironet 2800i Access Point" no puedo descargar el software hagame el favor de bajarme y subir a mega porfavor.. les agradeceria muchisimo.
Greetings, I need some guidance on how to revert back to capwap from mobility express.
Try this www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/82/user_guide/b_ME_User_Guide_82/appendix.html#topic_A575EE4B2A054DE5BAF1931A7D384DB5
Thanks! Do you know if I need to reimage same way I did to go mobility express? Or would the same image work for both ap-types?
You do not need to worry about it. When it finds the controller, the controller will push down the image.
Thanks @Cisco Sal I really appreciate the help!
Hey I am getting an error with DTLS LSC NOT PRESENT.any way to disable dtls on the ap? 1852i
Hi Cisco Sal did you preforemed the conversion befor setting the AP up ,
i have 1800 series that won't let me Type anything in the CLI it just keep looking for a CAPWAP server then it reboot itself after 15 attempt !!
Yes you have to convert it to mobility express before you set it up. Not sure why it's rebooting. Is it getting enough power?
Cisco Sal Yes it is geeting enough power from Thr POE , i accessed to it via console and it says CAPWAP state : discovering looks like i need a wireless controlled to set it up then i can convert to Mobility express ?!
No you do not need a controller. Follow the steps in the video and you should be fine.
@@CiscoSal I'm having the same issue now. Without a controller on the network, it's stuck in a boot loop because of repeated CAPWAP discovery failure. Any idea how we can handle this?
Hi men, Do you have the convertion step from mobility to capwap???
Hi, you should be able to find that info here www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/82/user_guide/b_ME_User_Guide_82/appendix.html
Cisco Sal Thanks, that is
can i save iOS file from mobility express to my PC? if yes please tell me the procedure
can you share the 1850i software conversion?
You can download it from Cisco.com
You need an account to be able to download the file
I can share with you let me check
If possible, could you share the software over the Mail???
For which Device , Router , Ap or Switch
@@sushilchavan692 i need for AP and switch
Thanks! Just to confirm, you require a K9C versus a K9 PID to convert a ME to CAPWAP and vice versa. But AIR-AP3802i-B-K9 (US PID) only with CAPWAP cannot covert to ME correct?
The ones I used were AIR-AP3802i-B-K9. So, yes these can be converted to ME. The difference is from an ordering perspective the K9C ones you can select to have the ME code on them from the factory. The k9 ones there is no option to select ME code at the time of ordering. So, if you get the AIR-AP3802i-B-K9 they will have to be converted, or you use them in CAPWAP mode.
Thanks Sal
Hi how do you remote into your client APS on your network I tried but cannot get in
You can cli into them. For a gui experience you log into the main controller AP.
for some reason I can't get to the ME through GUI. I just connected the 3800 to my laptop and did the upgrade. I should be ablle to access the ME on my laptop correct? 10.0.0.2...any suggestions?
You need to connect to the SSID that the AP puts out. Then you can connect to the GUI.
It prompted me to create an employee SSID when I was converting it. I don't see that SSID broadcast ed.
Do you have DHCP enabled on your switch?
Hello. but please tell me how you could enter your username and password. not how it doesn't work
i need mobility express image . Please share link
You can get the images from Cisco.com Thanks!
Cheers Mate!
I need the software. Why cisco did not give the me software for everyone
You can download the software from cisco.com. You can also purchase them with the ME software already loaded. I recommend talking to your partner to make sure they are selling you the correct version. If not they will probably default to the version that joins controllers.
@@CiscoSal cisco requied an account that subscribe to them to download the image. Meanwhilr i dont have that account. So if u have the image could you kindly mail it to me , will be very appreciate that
If you purchased the AP though cisco sanctioned channels then you can sign up for a cisco.com account and download the software. That’s how cisco protects themselves from unauthorized resellers.
If possible guide us, how to download the software from Cisco portal
At the time of perches product , you should pay for technical support they provide you all software reading our product as well as they as SR NO of product and they will be help you
I Need help , can you Help me sir ,
i have Ap modal no Air Ap 2802i-D-K9 , and i don't have controller but and want to convert 1 Ap as master Ap how i do ? you have iso file then provide me
You can download the file from Cisco.com you will need support on the ap to get it.
ok thanks
big help
Can you help me? Bro this solve is (RNAQ-C7)
Cant download software.I need some contract they said.Behh
Yes you need a support contract for software upgrades.