How to Replace Rear Drum Brakes 2006-2011 Honda Civic
ฝัง
- เผยแพร่เมื่อ 15 ต.ค. 2024
- Buy Now!
New Brake Shoe & Drum Kit from 1AAuto.com 1aau.to/ia/1ABD...
This video will show you how to install new drum or parking brake shoes on your 2006-2011 Honda Civic. For drum brakes and parking brakes, shoes will eventually need to be replaced. If you are overhauling your rear brake system, or just need to replace worn out shoes.
This process should be similar on the following vehicles:
2006 Honda Civic
2007 Honda Civic
2008 Honda Civic
2009 Honda Civic
2010 Honda Civic
2011 Honda Civic
Tools you will need:
• Flat Blade Screwdriver 1aau.to/obiX/1A...
• Pocket Screwdriver
• 19mm Socket 1aau.to/oagc/1A...
• Needle nose pliers 1aau.to/oDa/1AX...
• Needle nose pliers 1aau.to/oDa/1AX...
• 1/2 Inch Impact Gun 1aau.to/osB/1AX...
• 3/8 Inch Impact Gun
• Torque Wrench 1aau.to/oaDr/1A...
• Brake Grease
• Brake Parts Cleaner
• Copper Anti-Seize
• Drain Pan 1aau.to/ozd/1AX...
• Floor Jack 1aau.to/o4y/1AX...
• Jack Stands 1aau.to/oSU/1AX...
• Pick 1aau.to/oND/1AX...
• Wire Brush 1aau.to/osM/1AX...
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
I watched several videos on replacing Civic rear drum shoes (and wheel cylinders) and this was by far the best. Thanks!!!!!
Nice video. I changed my honda civic 2013 brake shoe same way. Tips for beginner: first remove the adjuster spring. That is not that hard. Then remove both side anchor pin and mounting clips and then lift the both shoes from bottom slots and then remove the bottom spring without any tension on it. After that just slide the both shoes upward and you can easily remove the top spring and adjuster. I followed same guide in this video for new shoes. I just used screw driver and simple plier for whole replacement process.
Thanks you for great video. 😊
When I bought my used 2011 Lx it had Drums, something told me get Discs on the rear Seriously a lil small voice said get Discs. I never looked back. It's so much easier with Disc brakes! Thank God!
TRQ and 1A Auto have saved me so much time and money. I am truly grateful for the time that you guys put into making these videos and teach the regular guys like us to do tough jobs like this!
Thanks, these close ups of the process are priceless! No class needed
also, if you can't remove the drum because it's baked tight...the two holes on the drum are for the M8/1.25 bolts...screw it in and keep going until you separate the drum. You can use one or two at the same time.
Great video! you were clear and detailed, making it easy to follow! thank you
Quite the thorough cleaning job. It almost looks like a brand new wheel bearing🤔
The horseshoe pin tested every ounce of my patience.
Drum brakes! Hate is not a strong enough word.😢
I don’t understand how you’re supposed to re adjust the adjuster lever after you’ve installed the drum. Do you just leave them fully loosened? Because if you tighten them back you can’t fit the drum back on, but if you don’t tighten them back you have no braking power. Please help
Thank you for this video was very easy to follow. ❤ the content and god bless
How did the clean the mating surface so well, or did you replace the part?
Thank you. Thank you. Thank you for this video! I found out to my amazement I had these drum brakes on my 2012 and while it took much more than 15 minutes as well as a whole lot more cuss words I got the job done. Also a thousand curses upon that top retention spring. Y'all make it look so easy and I just about decided to cut it off before it finally slipped out of it's hole and was replaced with a brand new spring.
Excellent how to. Thanks
Great video! Very well explained.
Thanks for this it’s just what I needed!
Half of my retaining spring is gone and my adjuster exploded so half of the hard work was already done for me
🤠👍
Great video thank you
So what the heck do I do when trying to remove the main spring shoots the brake piston out the other side?
on my 2014 honda civic my rear brake drum are stuck to the hub. I tried hitting it with a hammer to break it free with no lucK. i EVEN USED like solvent for rusty parts... what else can I do?
+Core Turkoane We do not have a video for this repair right now, but we'll keep this request in mind for a future video!
What did you use to spray clean the break?
Is this the parking brake?
Nice work.
Excellent
Brakes have no pressure. Bleeding doesnt help. Whats the issue?
+@khairt1731 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Nice video
Thank you
Daaaaaamn why so many clips
Use a shop vac or compressed air to spray out and clean the dust off everything. Never ever do what this guy did in the video. You do not want brake cleaner or parts cleaner getting in or around the rubber seals on the little piston in there.
Haynes repair manual does not recommend to use air to blow
What I learned is for brake drums only, use brake clean at first so dust doesn’t aerosolize because in many cases the brake dust is harmful and can contain asbestos so never use compressed air
Couldn’t even get the drum off lol