Solo Backpack Sprayer Repair ― Stopped by Stuck Cylinder
ฝัง
- เผยแพร่เมื่อ 22 ส.ค. 2024
- Today I started to repair my Solo Backpack Sprayer, and I ran into a stuck cylinder and could not continue. I need to contact them to continue 😕
Here are some more sprayer related videos you may enjoy:
Review of Solo 425 4-Gallon Backpack Sprayer -- Part 1 -- • Solo 425 4-Gallon Back...
Review of Solo 425 4-Gallon Backpack Sprayer -- Part 2 -- • Solo 425 4-Gallon Back...
Solo Backpack Sprayer Rebuild ― Success! -- • Solo Backpack Sprayer ...
Solo Backpack Sprayer Repair ― Stopped by Stuck Cylinder -- • Solo Backpack Sprayer ...
Chapin ProSeries Backpack Sprayer [Unboxing] -- • Chapin ProSeries Backp...
Chapin Backpack Sprayer Review [Vineyard Spray] -- • Chapin Backpack Spraye...
Solo Sprayer Down! ― But the Job Got Done! -- • Solo Sprayer Down! ― B...
Support Planet Mojo -- mojoprairie.co...
Please Share, Like, Comment, and Subscribe!
www.paypal.com...
Click here to subscribe ― / @planetmojo
Our Oak Savanna Website ― mojoprairie.com
The Modern Homesteader - www.bitchute.c...
Thank you for watching Planet Mojo and have yourself a great day!
#SoloSprayer
#SoloBackpack
#SoloBackpackSprayer
Update: I found a video on Gempler's TH-cam channel, and I'm doing things correctly, but the cylinder is just plain stuck. Many other people are having the same problem, and they recommend using a heat gun to warm the plastic around the cylinder. I'll give it a shot and the video will be out shortly 😐 The kit I use can be found here: Solo-K Piston Sprayer Pump Repair Kit -- amzn.to/2DbLfrK
Here is the video where I successfully remove the cylinder: th-cam.com/video/QEL510GBEBY/w-d-xo.html
The whole piston cylinder and pressure compartment are all one piece...and comes out as one piece with only an o-ring seal between the outside of the piston cylinder/pressure compartment assembly AND the tank.
Thanks!
So when I take my pressure compartment/piston cylinder out there is a little Philips screw up inside the piston cylinder that holds a rubber grommet in place above the piston. There is also a rubber piece inside the pressure compartment flopping around. If the piston cylinder and pressure compartment do not come apart, how do you replace whatever that rubber piece is inside the pressure compartment?
If you’re using powder use a diaphragm pump not a piston. Less wear and tear
Correct. I picked up one of them for the wettable powders and use this one for liquids now.
When you say plumber's grease do you mean high vacuum silicon grease? I would recommend that far over vaseline especially with plastic parts. Also not a bad idea to have some PB loosener on hand for rusted stuff then after cleaning, a nice good coat of WD. Actually, I've been thinking a spray coat of EZ-slide by Van Sickle ( a graphite based coating ) used by farmers for the obvious rust prevention plus it makes slick surfaces too. Anyway, I have a pump sprayer similar to this one. Not sure of the brand. It's definitely more of a commercial model and it's probably at least 20 years old. I have the same issue...no pressure...I put a different wand on it but I didn't really expect that to fix the issue. I've never cracked into one of these puppies before even though I worked in carpet and floor cleaning. Never had to do the maintenance. Hopefully I can find new gaskets for the inner workings if I need them. So, Thanks for your video! I think it helped me see through the mud! 😁💥💯💥👌👍👊💪🤙
the strainer is at the wand tip
Thanks William!
Use heat
Push it out from the inside out
Mine cannot pump water and there no leaks.
Sorry but this really didnt help me....If I wanted to see someone struggle trying to take it apart and not know really what is going on I could just watch myself!!! :)
Here is the successful video: th-cam.com/video/QEL510GBEBY/w-d-xo.html
How can order the repair kit
It is linked in the pinned comment, but here you go: Sprayer Pump Repair Kit -- amzn.to/2DbLfrK Good luck!
Amatiran