Step one: Thread a wooden rod Step two: Drill a hole in a wooden plank Step three: Thread that hole Step four: Add glue to the threaded hole Step five: Hammer the *threaded* rod in the *threaded* hole
The key to it seems to be stripping both the male and female threads. This guy is a moron. You can put female threads in wood (carefully), I do it often, but putting male threads on a wooden dowel with such a fine pitch (M12 is usually 1.5mm pitch). Typically, female threads in wood are used to screw in steel inserts which have a smaller female thread (e.g. M6) in them for securing parts together without using wood screws.
1. Оставляем шапку гвоздя, чтобы цепляться 2. Делаем рифление на штифте и в отверстие (резьбой это назвать сложно), чтобы детали ещё больше болтались 3. Вбиваем болт внутрь контргайки, чтобы когда она заржавела - можно было только срезать
1. More stability 2. A longer dowel 3. More secure, and plus it’s just a damn hole, when you take everything out so you can undo it pretty easily. it’s funny how these amateurs come out here and whine about something they don’t know shit about
Нарезать резьбу в отверстии, нарезать резьбу на шконте (вроде так называется), но все равно при сборке использовать молоток. Гениально. Интересно, со шпильками на головке блока цилиндров проканает?
They make lock nuts, lock washers, and thread locking compounds, there's a bunch of ways to lock nuts in place without drilling a hole. If you're going to drill a hole you could at least use a cotter pin instead of a smaller bolt and nut, now you have to worry about the little nut coming off 🙄
@lexingtonconcord8751 it does no good for holding. Dowels are usually glued in and the point of the longitudinal cuts you see in dowels is to allow the glue to escape as you fully seat the dowels. This idea was a failure as you can see the glue rupture the end grain as it squeezes out. If this worked it would have come out the top..
...#1 sweet jesus.... no... never go that straight downwards... aim for inbetween that.... because if you go straight down your now creating a fracture line along the wood grain where a slight bump will cause the wood to just break off. the piece of wood you got might work for that because the grain flows horizontally along the length but if it ever flows vertically you'll end up busting the end of the corner off easily.
I love your videos so much. Not because they are useful or have value, but precisely because they provide absolutely zero value whatsoever, and that is very impressive!
Надо было законтрить контр м4 контргайки м14, что бы просверлить контргайку м4 сверлом 1мм, что бы законтрить контргайку, пока та контрит контргайку м14.😂
1. Открою тайну, нужно взять саморез длиннее а так может вырвать так, как близко к краю доски. 2. Можно сверлить сверлом по дереву, прикинь. 3. Этот проволкорез не режет а отрывает, его уже протестировали. 4. И последнее... У тебя гровера нет !!?? Кто пользуется этими "лайфхаками"? 🤦🏻😫😖🙈🙉🤦🏻🤦🏻
Always use metalworking drills to make holes in wood? Put a countersunk screw in at 45 degrees to the surface, leaving the head sticking out, when you could just move it a bit lower. Don't use locknuts when you can just drill a hole through your (cheese soft nut and bolt - and make sure it isn't straight) and ram a machine screw through it. Clearly Russia or wherever these come from have not yet discovered split-pins or locking wire.
I worked for this guy once. He told me he could do my job better, and save some time & money, and he only hired me because he was tied up in the studio.
Ten ostatni przykład jest dyskusyjnym. Po to używa się dwóch nakrętek by jedna z nich kontrowała tę właściwą przenoszącą naprężenia montażowe. Można też użyć odpowiedniej nakrętki samoblokiującej z wkładką z tworzywa sztucznego lub odpowiednio ukształtowanym jednym z brzegów.
There is times when I'm working with nuts and bolts, when I don't want it to back out or come loose I just crimp the threads. That is for permanent install. I'm going to have to show the guys that are in charge of job security this one.
Bolts are graded for hardness, you can tell the grade by the marking on the top. However by appearance that's a grade 3 piece of all thread and very soft. That said jam nuts don't loosen
I'm convinced this channel is just trolling at this point.
Bro, you r too late to realize that
This is an asmr channel
@@ilhamh1596 If that's true it's very terrible at it.
It Is, but it gets clicks, and he’s making $300 a day from it..! ¯\_(ツ)_/¯
@@PANZERFAUST90 lmao
And why? You mad he knows more than you?
After watching 30 of these things, it finally occurred to me that this guy is just screwing with us. He can't be the stupid.
You'd be surprised
اااتلتىى
And he've been using wood screws all this time)!
Wait are these real tips or just jokes.
@@jaspertwinn9696please be sarcasm 🤣
Step one: Thread a wooden rod
Step two: Drill a hole in a wooden plank
Step three: Thread that hole
Step four: Add glue to the threaded hole
Step five: Hammer the *threaded* rod in the *threaded* hole
Why do any threads?
I swear this channel is just trolling us at this point
😅
Well there might be a case for the threads giving more conctact area dor the glue. But like it aint comming out either way...
The key to it seems to be stripping both the male and female threads.
This guy is a moron. You can put female threads in wood (carefully), I do it often, but putting male threads on a wooden dowel with such a fine pitch (M12 is usually 1.5mm pitch). Typically, female threads in wood are used to screw in steel inserts which have a smaller female thread (e.g. M6) in them for securing parts together without using wood screws.
В конце надо было ещё взять сверло на 1мм и сделать отверстие в маленькой гайке и закрутить на ней болт ещё меньше и так до бесконечности
😂
Зачем написал??? Теперь он выпустит новое видео где так и сделает 😢😢😢😢
И сваркой еще прихватить
1. Оставляем шапку гвоздя, чтобы цепляться
2. Делаем рифление на штифте и в отверстие (резьбой это назвать сложно), чтобы детали ещё больше болтались
3. Вбиваем болт внутрь контргайки, чтобы когда она заржавела - можно было только срезать
@@ДмитрийВысоцкий-щ1ь 238,❤️,
Правильно .забитый болт держит лучше чем вкрученый гвоздь
Саморез забитый молотком держит лучше, чем гвоздь закрученный отверткой)
Лучше забить саморез,чем выкрутить гвоздь.
Щось таке й Я зрозумів
250 полуляхов из 250ти😆
😁
Am I the only one confused on wth they accomplished with any of these? 😂
Useless
No you're not. This is dumb!
1. More stability
2. A longer dowel
3. More secure, and plus it’s just a damn hole, when you take everything out so you can undo it pretty easily.
it’s funny how these amateurs come out here and whine about something they don’t know shit about
@@hangingontheWildside nope got you to watch 3 things no tradesman would EVER waste our time on
your english is so much good
Нарезать резьбу в отверстии, нарезать резьбу на шконте (вроде так называется), но все равно при сборке использовать молоток. Гениально. Интересно, со шпильками на головке блока цилиндров проканает?
А, он все резьбовые соединения через молоток собирает...
Законтрить контргайку, потом аккуратно спилить контору, шлифануть и покрасить гайку в цвет, пусть потом попробует кто нибудь открутить 😂
Для вас отдельный котел грееться, 😄😄😄😄
А не проще просто приварить?
Да вы, батенька, знатный садист будете. И где ж это вас так научили над людьми издеваться? Или природный талант?
Amei o vídeo que legal 😮😮
They make lock nuts, lock washers, and thread locking compounds, there's a bunch of ways to lock nuts in place without drilling a hole. If you're going to drill a hole you could at least use a cotter pin instead of a smaller bolt and nut, now you have to worry about the little nut coming off 🙄
Looks like it would break super easy! That’s ok tho, I LOVE bustin’ nutz
Unless he tightened it
@@redemption9572 Or drill a hole through that for an even smaller nut & bolt.
Тем более, что он маленький болт забил в отверстие и испортил резьбу
Maybe they fix it by drilling a small hole into the little nut, locking with another smaller nut :)
Next video: using pry bars as flathead screwdrivers
and screwdrivers as crow bars
@@joemarchinski914 hammers as axes
Or Screws as bolts
This funny shit I've seen this month 😂😂😂😂😂
НУ потом чтобы маленький болт крепко держаться,его тоже надо делать как делали с большим,и потом так и так до бесконечности
Yes thread the dowel. That makes sense.
Pretty sure it's used to make the plug the approximate size easily..yes much of this is silly.
Threading the dowel and the hole created more friction on each surface, which would help hold the dowel better 👍🏻
@lexingtonconcord8751 it does no good for holding. Dowels are usually glued in and the point of the longitudinal cuts you see in dowels is to allow the glue to escape as you fully seat the dowels. This idea was a failure as you can see the glue rupture the end grain as it squeezes out. If this worked it would have come out the top..
well I enjoyed it
"I used the screws to secure the screws"
tap your wood and hammer your nuts
П0вг
Повторете
*bolts, but yeah.
Drill hole through tiny nut and put a smaller bolt like Russian nesting dolls
I was upset they didn't do that
I came looking for this comment
We need that in the next video. But it needs to be at least five Russian nesting bolts deep. 😅
Wow!!!!
thank you very much for teaching me how to thread wood
Now I can start building my house😊
...#1 sweet jesus.... no... never go that straight downwards... aim for inbetween that.... because if you go straight down your now creating a fracture line along the wood grain where a slight bump will cause the wood to just break off.
the piece of wood you got might work for that because the grain flows horizontally along the length but if it ever flows vertically you'll end up busting the end of the corner off easily.
It's becoming like 5minutesCrafts😂
good video I was inspired by you, thank you
Bravo! This is absolute genius!
What was that last one??? you must be trolling.
Nah, thats how you use ligma nuts
i was waiting for him to drill another hole in the smaller nut to "secure" that one too
Зачем было нарезать резьбы в отверстии и на нагеле, если ты его все равно забил молотком?
КПД равен нулю!
Вот у самого возник такой вопрос. А ещё зачем он контргайку просверлил🙄
@@likeme8791 что бы она не отвинтилась, коту понятно. Но я думаю надежнее было бы приварить
@@YuriProl можно просто на гровер
Может для лучшего склеевания, за счёт увеличения площади?
@@YuriProl чтобы она не отвентилась, ее можно просто за контрогаить
I love your videos so much. Not because they are useful or have value, but precisely because they provide absolutely zero value whatsoever, and that is very impressive!
Нахуя нарезать резьбу, а потом забивать???? 🤣🤣🤣
Не ищи здесь логики) она умерла вместе с тем деревянным болтиком😂😂😂😂😂
Today we have another episode of "how to do everything wrong"
Nice job .. Amazing
Excellent tips 😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊
Great video 😄
How to do thing with extra steps.
How to do nothing with extra steps
Надо было законтрить контр м4 контргайки м14, что бы просверлить контргайку м4 сверлом 1мм, что бы законтрить контргайку, пока та контрит контргайку м14.😂
For the first one JUST PUT THE SCREW CLOSER TO THE BOTTOM or get a longer screw
Забивать болт в болт это какая-то новая технология которая блокирует забив болта на дело?
amazing good job♥
ボンドがうにょんって出てくるとこ好きすぎる
Bizarre facts, 5.4 million people subscribed to this person
Законтрить контргайку - это сильно 😄
Да чел вообще не слабый, нарезал резьбу на чепике и в посадочном отверстии.
А не смутило что болт забивает и нормально гайка накрутилась .
Осталь только ее еще так же законтрить
@@mansel8312 Три раза. Последний подход под электронным микроскопом.
Всё херня, он не законтрил маленькую гайку
Dude went through all that trouble to thread that thingy AND tap the hole all to just hammer it in... WTF?!
В маленькой гайке надо просверлить дырку сунуть болт ещё меньше и закрутить гайкой
The glue pooping out the side like that was awesome
Did this dude really just thread a hole just to hammer a peg into it
Резьба не будет держать, так как нарезать надо метчиком по дереву.
hahah, you gotta love it... the "lock nut" got me laughing
Are you trying to tell me that if I want to screw something vertically, my tool should be vertical too?
Omfg, life-changing tip
First one is good.
Ive seen the Italian army be more productive in world War 2
Do a tutorial on how to flat your jack with the car while fixing the lift tire.
You didn’t embed the screw. But that wood turning idea was good, thanx.
Amazing 👌👌👍👍💕💕💜
1. Открою тайну, нужно взять саморез длиннее а так может вырвать так, как близко к краю доски.
2. Можно сверлить сверлом по дереву, прикинь.
3. Этот проволкорез не режет а отрывает, его уже протестировали.
4. И последнее... У тебя гровера нет !!??
Кто пользуется этими "лайфхаками"?
🤦🏻😫😖🙈🙉🤦🏻🤦🏻
Good job👍👍👍👍
Always use metalworking drills to make holes in wood? Put a countersunk screw in at 45 degrees to the surface, leaving the head sticking out, when you could just move it a bit lower. Don't use locknuts when you can just drill a hole through your (cheese soft nut and bolt - and make sure it isn't straight) and ram a machine screw through it. Clearly Russia or wherever these come from have not yet discovered split-pins or locking wire.
Thnks a lot iam hoobyst and your videos are good ideas.
What's the piece of metal used for making the round stick?
I worked for this guy once. He told me he could do my job better, and save some time & money, and he only hired me because he was tied up in the studio.
Very well tips
Wow! Cool and I'm here
The sound of the screwdriver is really pleasing to the ears
What about drilling the little nut and bolt too to secure it lol
Because you need to thread wood 🤨 and…… ruin threads on all your bolts by smashing with a hammer🤦♂️nice 🤔
now I know why my wood screws dont work, I didnt use my tap to thread the board
Aint no way homie just threaded wood
@@syrupchugger4056 threaded wood definitely has uses, look at a broomstick for instance.
But this guy knows none of those uses.
Nobody:
Modern art:
I’m concerned this channel will be the next Five Minute Crafts.
Freedom of speech
A clogged screw holds on tighter than a twisted nail!
Carl: "Hey Benny, you want some loctite for those nuts?"
Benny: "Naaah check thisout. I saw this on a YT short! "
Carl: 😰
I'm amazed he used a screwdriver in the first one instead of a hammer.
How did those threads work out in that 2x4 you stuffed a plug into?
After the last one I do t trust a word you say😂😭
Ten ostatni przykład jest dyskusyjnym. Po to używa się dwóch nakrętek by jedna z nich kontrowała tę właściwą przenoszącą naprężenia montażowe. Można też użyć odpowiedniej nakrętki samoblokiującej z wkładką z tworzywa sztucznego lub odpowiednio ukształtowanym jednym z brzegów.
когда первый раз взял шуруповерта !!!!!
Crossed threads are better than no threads.
Лоботамию сверлом сделай себе, гениальный автор😂
First good. Next one, WTH? Make dowel, drill hole, THREAD HOLE, hit dowel in with hammer 🤪
Trust me, I'm an engineer.😂
There is times when I'm working with nuts and bolts, when I don't want it to back out or come loose I just crimp the threads. That is for permanent install.
I'm going to have to show the guys that are in charge of job security this one.
Надо было в последней части маленькую гайку посадить на клей, подложить гровер и законтрагаить.😂
Надо было в этой маленькой гайке тоже просверлить отверстие и запихнуть туда мини болт. 😂
Just tighten the sekond nut and revers the the first end it will never losen...
There's a difference here between those who do....and those who teach. Who taps wood? 🤣
木の棒にめねじ切りとかおねじ切りとか出来るんかな？と思ってたら叩きつけて刺してて笑った
The last one is specially for Boeing 😂
Откуда в психушке инструменты!?!? Куда смотрят санитары!? 😵
Лайфхаки срочно к доктору!!!!
Tool tip 2. Use wood drilling bit on wood, not metal drilling bit.
So many ways to do 'it'.
Overkill 🤣
Дью, в студию!
Чтобы зафиксировать гайку не проще ли капнуть суперклея?
Всё что с резьбой мы будем заколачивать... 😂👍
So amazing 😂
The last one you compromised the bolt I would never do that on any critical bolt
Какая умничка появилась
Wheres the bolt to stop the tiny bolt, and the tinier bolt for the tiny bolt? How far does it go? Is it tinier bolts all the way down?
Минуты три ржал с резьбы 😂
Engineering Pinnacle 🧐
if you're going to drill through one of the nuts anyway,...you only need ONE nut.
so why do all of us have two nuts?
Did anybody else think they were looking at the pyramid of gisa 😅🤦♂️
Aren't nuts high carbon steel? Would it be that easy to drill through that?
Bolts are graded for hardness, you can tell the grade by the marking on the top. However by appearance that's a grade 3 piece of all thread and very soft. That said jam nuts don't loosen