Thank you for the guide. My CLP-310's image unit really came to the end of its life and I bought two other used devices, CLP-310 and CLP-315. I placed the reset switch in my old printer and in the other CLP-310, also checked the cables and switch function. Neither this hack nor putting a 56 Ohm resistor into the image unit did work. Any other idea? After 3½ hours I cleaned/replaced several parts of the CLP-315 and now I am able to print. Not perfect, but that will have to do.
The key is to switch off the reset switch when the LED is green for the first time. My CLP 315 (clp 310 series) also needed to have taped on its chips in order to work the reset.
Please tell me the second wire you connect is to the ground of the board? Get me out of this doubt because I'm going to do this procedure on samsung clx3185N I already found the piece now the second wire will be on the ground that I call ???
Hello, thank you for the super instruction. At my printer the chip U1 was in a different location, but looking for the name of the chip it will work. I did a little change by connectiong ground. You can find ground at pin 4 of the chip, so it will be a little easyer to do. Just make a switch beetween pin 4 and 5 of the EEPROM. best regards Martin
Üdv, Egyszerűnek tűnik, nekem mégsem sikerült. CLP-315-öm van és minden esetben piros ledet kapok a próbálkozások alkalmával. Reset kapcsolás nélkül elindul, de mindenre emlékszik, ha a reset kapcsolóval indítom, akkor 8-10 mp után boot közben pirosra vált a led. Van erre megoldás?
+Foreman Szia! 310 esetén a tonerek megmozdulásakor el kell engedni a reset kapcsolót, 315 esetén pedig úgy emlékszem az egész boot folyamat alatt nyomva kell tartani. Kísérletezz, sikerülnie kell. Legyen szép napod!
+Fenyutas, Köszönöm, megpróbálom, egyelőre azzal küzdök, hogy a tisztítás-porszívózás-sűrített levegő után szellemképes marad a nyomat. Úgy veszem észre, hogy a továbbító szalag festékes marad. Arról le kellene húznia valaminek a port?
Szia nem tudom nekem segítene ez a resset? a nyomtatóval az a gáz h kinyomtatja az oldalt viszont nem nyomja ki a lapot, lehet ez is ilyen beépített turpisság a samsung részéről 13044 total image count után? és a resset orvosolná? várom a válaszod előre is köszi, ja am teljesen ugyan erről a videóban látható nyomtatóról van szó
Szia! Az meg hogy lehet? A kinyomtatás egy hengerelési folyamat során megy végbe, tehát "kitolja magából" a lapot. Talán valahova félre siklik a lap és benne marad a nyomtató házában? Ezt biztosan nem orvosolja a chip reset. Legyen szép napod!
Hi, I have a CLP300. I executed all steps as explained in the video. Unfortunately when I restart the printer it only works if the reset switch is off and the counters are not decreased. If I first switch the reset on and then turn on the printer, switching off the reset after a while (tried with different delays) I only have it stuck with all red lights on. What am I doing wrong? Thanks
@@Fenyutas Oh I am working on this issue too. I was so proud and satisfied with this printer, having invested a bit more than getting the cheapest ink jet. But low and behold how it has looked up itself with a steady red light. I have ben cleaning it meticulously inside, changed the toners, fiddled and almost started believing all the reset card scams. Opened to find the reset chip once but now obviously I have to do that again. I might just cut thru the plastic on the side as it´s crap anyway if I don´t manage. I really need and want my printer. Never again a Samsung printer! What I will do is I will basically look for the size and look of the chip I think it is that looks similar to this 24c64wp chip, determine if it does the similar task and then bend a cable and hold it (as I saw in another clip about a slightly more advanced model).
@@ifthebeltiscrackedor 24c64wp is a eeprom, Electronicly erasable programmable read only memory (bit misleading in the read only part) its writable storage that wont be erased when the power is lost (like with RAM). Its also availeble in 16, 128 and lager and smaller "sizes" as in storage. Not all devices check if the chip ID is the same and if not, any 24C?? will do if the size and protocol is the same they speak. to be safe, buy another 24C64 (maybe a 24C64WP, the C is the voltage level they speak on.) This mod prevents the samsung from talking to the eeprom, other tricks is to remove the IC, read its contenst, modify it somehow (crc checks might be there) and put it back. or find a very new, fresh dump of this IC and write the contents of the new one to the one on a expired printer. but youll have to write all again, with this mod, just flip the switch and do it all again). For other printers where this trick doesnt work, try make a dump of your eeprom and look at the contenst of the eeprom. (make 1000 backups) then alter with a hexeditor some counters (try also to see if they use some checksum). put the eeprom back and see if it works. worst case, find a printer thats very new and unused, use a copy of that printers eeprom and flash it to yours (match the model please). I am gonna dump my eeprom first, and then reset it. so I can compare the contents after the reset as seen in this video,.
Szia! Kipróbáltam, működik, de egy gond van, a toner chippeket nem nullázza ki nekem meg még vagy negyedig van a toner és a hülye chip miatt nem birok nyomtatni. Amúgy mindent kinulláz, a szériaszámot is kitörli az összes hibakóddal együtt, de a toner chippre nem tudsz valamit?Ebben a nyomtatóban ha jól láttam 3 tonerbe nincs is Chip. Az meg hogy?
Szia! Már régen csináltam, de azok az érintkezők, amik a toner kifelé néző oldalán vannak a gyárilag szállított tonerek esetén eleve egy műanyag lapkával helyettesítettek, és a fekete legalul szintén le lett fedve egy szigetelő szalaggal és nekem így sikerült. Nem tudom mit értesz "el sem indul" alatt, de ha ez a reset procedúra megtörtént már kaphatnak érintkezést a tonerek.
kepfeltoltes.hu/view/160806/ScanImage001_www.kepfeltoltes.hu_.jpg Ennyire jutok vele, ha a tonereket leragasztom, bármelyik is hiányzik, el sem indul a folyamat, semmi nem mozdul meg, csak a tonerledek villognak felváltva, majd az állapotjelző pirosra vált, és ennyi. Szerinted ezek gyári chippek lehetnek? Alig nyomtattam vele 80% ban csak szövegnyomtatásra használtam és még 2 csomag printerlapot se bírt...
Hello, I performed all steps. Like you, I had the toner without a chip. Now I do not recognize any toner. Do you have any idea that I could have done wrong? Or what can I do to correct it? Thank you very much!
Hello, Thanks for answering! I could not prove it because not recognizing the toner does nothing. I tried to install it again and an option of the installation program was to make a test print, it printed the color but not the black one. That was the only thing I could print because all the time all the red LEDs are on and the smart panel tells me that all the toners are invalid and empty
Please repeat the all reset procedure. Very important, that release the reset switch (swith on) when the toners start moving. (when the printer start "click-clack") Toner chips are covered?
Yes, the chips are covered. I already repeated the operation and the same thing happens, it does not recognize the toners. Can the SDA connector (5) and the SCL (6) have been in contact with the weld? Or in that case should not work?
+Foreman Szia! Ha csak azt másoltad le, amit a videóban láttál nem mehetett tönkre, viszont az én tudásom csak ennek a resetnek a végrahajtásáig terjed, tehát többet nem tudok segíteni, de a neten biztosan találsz valami használható segítséget, ez egy elég régi típus valakinek lehetett hasonló problémája. Legyen szép napod!
Than you my friend. i just want to ask you something it happend to me, i did all you did but my printer is in a cycle on off(connected and disconnected to my pc). what do you think about i?
Muchas gracias amigo por el consejo. lo hice y funcionó de maravilla. Gracias a ti tenemos impresora para rato. Quienes lo intenten no perderán mas tiempo. este método funciona. Excelente aporte.
the CLP-320 printer did it according to the scheme, cleared the memory, stopped printing, captures the sheets and gives out blank, even diagnostic sheets.
Kabelki 0,5 metrowe podłączone do włącznika mogą się okazać nieco za krótkie, 2,5 m działał by znacznie lepiej, a i przekrój można było znacznie zwiększyć, a co tam żałować miedzi, mamy jej więcej od Chińczyków. Co do lutowania i klejenia, ocena jak najbardziej trafna czyli docha.
Działa! sprawdzone! i pomyslec ze jeszcze kilka lat temu trzeba bylo do tej drukarki chipy i inne kombinacje! A! reset ten trzeba robic na testowych tonerach albo pozaklejac styki bo inaczej nici z tego. pozdrawiam. ps w sumie to ja tylko na klika chwil do masy jeden kabelek dotknalem nie zakladalem tak jak tu wylacznika ale to jak tu jest pokazane jest juz na wieki zeby kolejny raz nie rozkrecac drukarki! OK!
A co może być jeśli drukarka clp-315 działała a nagle jak przytrzymuje przycisk aby wydrukował stronę testowa to nic się nie dzieje a zielona dioda miga i cisza nie słychać nic jak by siewylaczyla a dioda miga ?
Sooo, who to give credit to? its a eeprom, it holds the page count, you short the eeprom data line to ground, now the mcu cant read the data, does some diagnositics and you put the dataline back on the normal lines and allow the mcu to write default data, now it works as new... not that special. Only the very first person who found this trick could be credited, but ive seen multiple people come up with the idea, the execution is difernetly and results are basicly the same. But yes, wonder who is the socalled first :P
This worked great! I just missed the part in the beginning to tape up the cartridges. :) Thanks for sharing!
Thank you for the guide. My CLP-310's image unit really came to the end of its life and I bought two other used devices, CLP-310 and CLP-315. I placed the reset switch in my old printer and in the other CLP-310, also checked the cables and switch function. Neither this hack nor putting a 56 Ohm resistor into the image unit did work. Any other idea?
After 3½ hours I cleaned/replaced several parts of the CLP-315 and now I am able to print. Not perfect, but that will have to do.
The key is to switch off the reset switch when the LED is green for the first time. My CLP 315 (clp 310 series) also needed to have taped on its chips in order to work the reset.
What do you mean by "needed to have taped on its chips"?
Please tell me the second wire you connect is to the ground of the board? Get me out of this doubt because I'm going to do this procedure on samsung clx3185N I already found the piece now the second wire will be on the ground that I call ???
Excelente... Nos funcionó en una Samsung CLP 365W... Mil gracias por compartir
Puenteaste la pata de la eeprom a masa? Cada vez que la prendes tenes que hacer el proceso del accionar el switch de reset ?
Hello,
thank you for the super instruction.
At my printer the chip U1 was in a different location, but looking for the name of the chip it will work. I did a little change by connectiong ground. You can find ground at pin 4 of the chip, so it will be a little easyer to do. Just make a switch beetween pin 4 and 5 of the EEPROM.
best regards
Martin
can you just open short pin 4 to 5 and reassemble and its reset or does it need to power on
Martinussaurus u
Üdv, Egyszerűnek tűnik, nekem mégsem sikerült. CLP-315-öm van és minden esetben piros ledet kapok a próbálkozások alkalmával. Reset kapcsolás nélkül elindul, de mindenre emlékszik, ha a reset kapcsolóval indítom, akkor 8-10 mp után boot közben pirosra vált a led. Van erre megoldás?
+Foreman Szia! 310 esetén a tonerek megmozdulásakor el kell engedni a reset kapcsolót, 315 esetén pedig úgy emlékszem az egész boot folyamat alatt nyomva kell tartani. Kísérletezz, sikerülnie kell. Legyen szép napod!
+Fenyutas, Köszönöm, megpróbálom, egyelőre azzal küzdök, hogy a tisztítás-porszívózás-sűrített levegő után szellemképes marad a nyomat. Úgy veszem észre, hogy a továbbító szalag festékes marad. Arról le kellene húznia valaminek a port?
Does this also RESET the Toner cartridge counters?
Üdv Nekem egy 365w-m van de nem tudom sehogy kinullázni ha tudna nekem bárki segíteni azt megköszönném !!!
Is this a reset for the Toner Cartridges? Drum? or both?
Szia nem tudom nekem segítene ez a resset? a nyomtatóval az a gáz h kinyomtatja az oldalt viszont nem nyomja ki a lapot, lehet ez is ilyen beépített turpisság a samsung részéről 13044 total image count után? és a resset orvosolná? várom a válaszod előre is köszi, ja am teljesen ugyan erről a videóban látható nyomtatóról van szó
Szia! Az meg hogy lehet? A kinyomtatás egy hengerelési folyamat során megy végbe, tehát "kitolja magából" a lapot. Talán valahova félre siklik a lap és benne marad a nyomtató házában? Ezt biztosan nem orvosolja a chip reset. Legyen szép napod!
köszi ezzel már okosabb lettem, most van először ilyen nyomtatóm akkor meglesem a mechanikát
Kiváló video kolléga tudja, hogyan FUSOR és visszaállítja a TRANSFER
Hi, I have a CLP300. I executed all steps as explained in the video. Unfortunately when I restart the printer it only works if the reset switch is off and the counters are not decreased. If I first switch the reset on and then turn on the printer, switching off the reset after a while (tried with different delays) I only have it stuck with all red lights on. What am I doing wrong? Thanks
Only to hold the reset button until the printer begins to pound, then let go.
Thanks. This is what I do, but soon after I release the reset all leds turn red and nothing more happens and the printer does not work.
Sorry, I can't help!
OK :-(
Do you know if it is possible to do the same on the Samsung clp-300?
What does shorting the SDA line supposed to do?
Hello, do you know this reset, works with samsugn c410w?
I don't know.
@@Fenyutas Oh I am working on this issue too. I was so proud and satisfied with this printer, having invested a bit more than getting the cheapest ink jet. But low and behold how it has looked up itself with a steady red light. I have ben cleaning it meticulously inside, changed the toners, fiddled and almost started believing all the reset card scams. Opened to find the reset chip once but now obviously I have to do that again. I might just cut thru the plastic on the side as it´s crap anyway if I don´t manage. I really need and want my printer. Never again a Samsung printer! What I will do is I will basically look for the size and look of the chip I think it is that looks similar to this 24c64wp chip, determine if it does the similar task and then bend a cable and hold it (as I saw in another clip about a slightly more advanced model).
@@ifthebeltiscrackedor 24c64wp is a eeprom, Electronicly erasable programmable read only memory (bit misleading in the read only part) its writable storage that wont be erased when the power is lost (like with RAM). Its also availeble in 16, 128 and lager and smaller "sizes" as in storage. Not all devices check if the chip ID is the same and if not, any 24C?? will do if the size and protocol is the same they speak. to be safe, buy another 24C64 (maybe a 24C64WP, the C is the voltage level they speak on.)
This mod prevents the samsung from talking to the eeprom, other tricks is to remove the IC, read its contenst, modify it somehow (crc checks might be there) and put it back. or find a very new, fresh dump of this IC and write the contents of the new one to the one on a expired printer. but youll have to write all again, with this mod, just flip the switch and do it all again).
For other printers where this trick doesnt work, try make a dump of your eeprom and look at the contenst of the eeprom. (make 1000 backups) then alter with a hexeditor some counters (try also to see if they use some checksum). put the eeprom back and see if it works. worst case, find a printer thats very new and unused, use a copy of that printers eeprom and flash it to yours (match the model please).
I am gonna dump my eeprom first, and then reset it. so I can compare the contents after the reset as seen in this video,.
Szia! Kipróbáltam, működik, de egy gond van, a toner chippeket nem nullázza ki nekem meg még vagy negyedig van a toner és a hülye chip miatt nem birok nyomtatni. Amúgy mindent kinulláz, a szériaszámot is kitörli az összes hibakóddal együtt, de a toner chippre nem tudsz valamit?Ebben a nyomtatóban ha jól láttam 3 tonerbe nincs is Chip. Az meg hogy?
Szia! A toner chipek nem is kaphatnak feszültséget, mert az érintkezőiket le kell ragasztani! Legyen szép napod!
Szia, de nem működik akkor, el sem indul az egész..
Szia! Már régen csináltam, de azok az érintkezők, amik a toner kifelé néző oldalán vannak a gyárilag szállított tonerek esetén eleve egy műanyag lapkával helyettesítettek, és a fekete legalul szintén le lett fedve egy szigetelő szalaggal és nekem így sikerült. Nem tudom mit értesz "el sem indul" alatt, de ha ez a reset procedúra megtörtént már kaphatnak érintkezést a tonerek.
kepfeltoltes.hu/view/160806/ScanImage001_www.kepfeltoltes.hu_.jpg
Ennyire jutok vele, ha a tonereket leragasztom, bármelyik is hiányzik, el sem indul a folyamat, semmi nem mozdul meg, csak a tonerledek villognak felváltva, majd az állapotjelző pirosra vált, és ennyi. Szerinted ezek gyári chippek lehetnek? Alig nyomtattam vele 80% ban csak szövegnyomtatásra használtam és még 2 csomag printerlapot se bírt...
A legszebb az egészben, hogy a tonerek több mint félig vannak porral, az elhasznált porgyüjtőben is csak kb fél gyufásdoboznyi "szemét" volt.
Hello,
I performed all steps.
Like you, I had the toner without a chip. Now I do not recognize any toner.
Do you have any idea that I could have done wrong? Or what can I do to correct it?
Thank you very much!
The printer working right, but don't recognize the toners, or the printer works irregular too?
Hello,
Thanks for answering!
I could not prove it because not recognizing the toner does nothing.
I tried to install it again and an option of the installation program was to make a test print, it printed the color but not the black one.
That was the only thing I could print because all the time all the red LEDs are on and the smart panel tells me that all the toners are invalid and empty
Please repeat the all reset procedure. Very important, that release the reset switch (swith on) when the toners start moving. (when the printer start "click-clack")
Toner chips are covered?
Yes, the chips are covered.
I already repeated the operation and the same thing happens, it does not recognize the toners.
Can the SDA connector (5) and the SCL (6) have been in contact with the weld? Or in that case should not work?
Sorry, from here, I'm not competent!
hello. Can a similar operation be performed for the C430W?
Hi, sorry I don't know. Have a nice day!
All EEPROMS at Datasheets at alldatasheets looks very similar, so try..
Are you try?
Hello your method seems excellent, just wanted to know if you can apply the same method for a samsung xpress model M2825ND?
Sorry, I don't know.
Does it work with CLP-360 printer families?
Nos, azt hiszem a család most pipa lesz rám - lévén hálózati nyomtató - a led és mind a 4 szín ledje folyamatosan piros bekapcsolás után.
+Foreman Szia! Ha csak azt másoltad le, amit a videóban láttál nem mehetett tönkre, viszont az én tudásom csak ennek a resetnek a végrahajtásáig terjed, tehát többet nem tudok segíteni, de a neten biztosan találsz valami használható segítséget, ez egy elég régi típus valakinek lehetett hasonló problémája. Legyen szép napod!
+Fenyutas Köszönöm a segítséget. Nem a videón múlt.
Than you my friend. i just want to ask you something it happend to me, i did all you did but my printer is in a cycle on off(connected and disconnected to my pc). what do you think about i?
Hi, I think repeat the all procedure. I hope fix it. Have a nice day!
Good Morning! Can this procedure be done on clp365w?
Sorry, I don't know!
All EEPROMS at Datasheets at alldatasheets looks very similar, so try..
Muchas gracias amigo por el consejo.
lo hice y funcionó de maravilla.
Gracias a ti tenemos impresora para rato.
Quienes lo intenten no perderán mas tiempo. este método funciona.
Excelente aporte.
HOLA AMIGO SABES COMO PUEDO PEDIR O COMPRAR EL CONECTOR Y LOS CABLES TU QUE YA REALIZASTE EL METODO,TE LO AGRADECERIA MUCHAS GRACIAS
Hola Amigo! Tambien tengo la duda de sin el pin 5 (SDA) se conecta a 5v o al GND ?? Te agradeceria tu respuesta, ya que intento hacerlo para ML 2165W.
¿amigo se puede hacer lo mismo con una clp 325?
@@PedroPerez-hw1tm a GND
doesn't work on M2020W, I guess it keeps records on the toner
Hello, do you know this reset, works with samsugn SL-M2070W
Would also like to know this
FUNCIONA CON UNA CLP 325W?
Hello, dit you know this reset, works with samsung 320 with the 24c64wp chip
Hello! Sorry, I didn't.
Does it work with CLP-310N
we have cp-325 we couldt find the any place for second cable on mainbord could you help
Either it is minus(ground) or it is VCC(+). I´m looking into it now.
my printer does not detect magenta toner, what can I do to make it detect it? I already bought the original Samsung
Thank you gold hand man.
CLP-325 !!!OK!!! THANK YOU
Абдулгафур Раимджанов приветствую, 325 точно также сделать и сбросится?
Hello, does this method work for clp 315?
Sorry, I tried it to my clp310 only. But I think it will work, because difference clp310 and clp315 only network capability. Have a nice day!
Thank you very much, I'll try and tell you if it works
hey Angel... did you ever try this on your 315? I have a 315w and wondering if this will work?
hello. is to 5v pin or ground ?
Yeah why the heck doesent he tell us
Ground
the CLP-320 printer did it according to the scheme, cleared the memory, stopped printing, captures the sheets and gives out blank, even diagnostic sheets.
Para CLP 320 que el led indicador se queda en color Rojo fijo sin parpadear. Es el mismo procedimiento ???
So switch ON means short SDA to GND, and Switch off means wire circuit is open? Pls
Hi, yes! Have a nice day!
hello there is any manual reset of the tonner waste tank pl revert me
Sorry, I don't know.
tank you man from mexico
Hali!
Ez működik CLP-300-nál is?
+Kemény Valter Szia! Sajnos azt nem ismerem, nem tudom.
+Fenyutas Rendben, azért köszi.
All print like this working or not
what about samsung m3320nd. pls help
Guide for scx3206 printer plz
Kabelki 0,5 metrowe podłączone do włącznika mogą się okazać nieco za krótkie, 2,5 m działał by znacznie lepiej, a i przekrój można było znacznie zwiększyć, a co tam żałować miedzi, mamy jej więcej od Chińczyków. Co do lutowania i klejenia, ocena jak najbardziej trafna czyli docha.
I wat to reset ink level of hp inkjet printer by using this method.can u please tell me if it is possible?
dear friends, How to reset the samsung k2200 drum chip.
Programmer can achieve。
Can you able to guide me for Samsung ml1640 printer
Sorry, I can't! Have a nice day!
numer firmwear my bro And I will overtake you the reset And I will overtake you ok bro
numer firmwear
www.testcopy.ru/forum/downloads.php?cat=7
fix-printer.com/en/download/for-printer-reset/120-download-the-original-firmware-samsung.html
Działa! sprawdzone! i pomyslec ze jeszcze kilka lat temu trzeba bylo do tej drukarki chipy i inne kombinacje! A! reset ten trzeba robic na testowych tonerach albo pozaklejac styki bo inaczej nici z tego. pozdrawiam. ps w sumie to ja tylko na klika chwil do masy jeden kabelek dotknalem nie zakladalem tak jak tu wylacznika ale to jak tu jest pokazane jest juz na wieki zeby kolejny raz nie rozkrecac drukarki! OK!
do c430w też zadziała
@@krzwin2806 te funcionó????
A co może być jeśli drukarka clp-315 działała a nagle jak przytrzymuje przycisk aby wydrukował stronę testowa to nic się nie dzieje a zielona dioda miga i cisza nie słychać nic jak by siewylaczyla a dioda miga ?
I would like to know if anyone has wired a sl_m2020w. It has that chip. The number on mine is 24C64wp.
All EEPROMS at Datasheets at alldatasheets looks very similar, so try..
How To Reset Chip Ricoh Aficio FX200 & REX ROTARY DSM520PFL Chip Model : ML-2150 OPC BD V2.0
At least give credit where it is due.
Sooo, who to give credit to? its a eeprom, it holds the page count, you short the eeprom data line to ground, now the mcu cant read the data, does some diagnositics and you put the dataline back on the normal lines and allow the mcu to write default data, now it works as new... not that special.
Only the very first person who found this trick could be credited, but ive seen multiple people come up with the idea, the execution is difernetly and results are basicly the same. But yes, wonder who is the socalled first :P
CLP 325W ???
All EEPROMS at Datasheets at alldatasheets looks very similar, so try..
sprawdziłem,działa polecam!
Afarim
Tnkyou
Use EDC.exe tool from Samsung - it's much easier to reset all counters - only software - working for CLP-310
thank you :-)
samsung c430w też
Te consulto pudiste resetear la c430w con este método confirmar gracias??????
@@chuse83 To ja się pytam czy w c 430w działa
@@krzwin2806entiendo que si SOS el que pregunta y yo te pregunto a ti si pudiste solucionarlo de algún modo
وايضا طابعة سامسونج CLX3185FN ارجو الرد
m2020w RESET please.
Do you know where is this chip in an Samsug CLX 3185 printer?