ขนาดวิดีโอ: 1280 X 720853 X 480640 X 360
แสดงแผงควบคุมโปรแกรมเล่น
เล่นอัตโนมัติ
เล่นใหม่
class job mate, gives me an idea how to get at my cv boot that needs done for mot. Need more people uploading like you do 👍
Thank you for your support 🙂
Thank you for that I now know the sizes of sockets needed
Thanks for the feedback 😊
Great work mate. Love seeing the rust in those Euro D40s fall to the ground.
Thank you 😊
Excellent job mate
Thank you 👍🏻
did you torque the axle bolt?
No, he hammered away with a 800 ft-lb impact wrench.
did you quote for bottom ball joint ? on camera looks knackard .missing castle retainer the split pin goes in drive shaft ,also bad camera looks like fluid grease coming from track rod boot i love your videos keep up the good work thanks
Yes ball joint does need doing.These vehicles don't have a castle retainer on driveshaft.
Muchas gracias po el video me ahorraste muchos dolares saludos desde mexico
Muchas gracias por su apoyo. México es un país tan hermoso
once you remove the wheel bearing can you remove and replace the shaft or will you need to unscrew anything else?
Does those parts fit a Nissan Xterra 2000?
If I have the parts how much will be the labour?
good day, I tried to order "front wheel hub bearing for Navara 4x4 2009 model" in Lazada priced at 4128pesos, how can I chat with you? Is it new?
Does it matter if the new bearing has no sensor
No sensor would cause an ABS/Traction control fault light
Hi jimmy how much do you charge for this job, thanks
It was around £200
@@ORileysAutos inclusive of parts or add on top?I am doing two this weekend for GF along with discs/pads.
@@ricardobranco7357 inclusive of parts
It was raining rust when you were hammering it
6:35 🤣 I didn't even notice I had to watch it again
Some of it is probably mud
Use a bungee or wire to hold that caliper up and out of the way, otherwise good job
Next time I'll try better
Reuse the old cotter pin?
Lube year shaft before you stick it in the flange 😂
Great advice for any situation 👍🏻
class job mate, gives me an idea how to get at my cv boot that needs done for mot. Need more people uploading like you do 👍
Thank you for your support 🙂
Thank you for that I now know the sizes of sockets needed
Thanks for the feedback 😊
Great work mate. Love seeing the rust in those Euro D40s fall to the ground.
Thank you 😊
Excellent job mate
Thank you 👍🏻
did you torque the axle bolt?
No, he hammered away with a 800 ft-lb impact wrench.
did you quote for bottom ball joint ? on camera looks knackard .missing castle retainer the split pin goes in drive shaft ,also bad camera looks like fluid grease coming from track rod boot
i love your videos keep up the good work thanks
Yes ball joint does need doing.
These vehicles don't have a castle retainer on driveshaft.
Muchas gracias po el video me ahorraste muchos dolares saludos desde mexico
Muchas gracias por su apoyo. México es un país tan hermoso
once you remove the wheel bearing can you remove and replace the shaft or will you need to unscrew anything else?
Does those parts fit a Nissan Xterra 2000?
If I have the parts how much will be the labour?
good day, I tried to order "front wheel hub bearing for Navara 4x4 2009 model" in Lazada priced at 4128pesos, how can I chat with you? Is it new?
Does it matter if the new bearing has no sensor
No sensor would cause an ABS/Traction control fault light
Hi jimmy how much do you charge for this job, thanks
It was around £200
@@ORileysAutos inclusive of parts or add on top?
I am doing two this weekend for GF along with discs/pads.
@@ricardobranco7357 inclusive of parts
It was raining rust when you were hammering it
6:35 🤣 I didn't even notice I had to watch it again
Some of it is probably mud
Use a bungee or wire to hold that caliper up and out of the way, otherwise good job
Next time I'll try better
Reuse the old cotter pin?
Lube year shaft before you stick it in the flange 😂
Great advice for any situation 👍🏻