Jandy TruClear Salt System Settings and Menu Set Up
ฝัง
- เผยแพร่เมื่อ 5 ก.ย. 2024
- Jandy TruClear Salt System Settings and Menu Set Up
In this video I walk you through the Jandy TruClear Salt System set up and navigate you through the system settings. It is a very simple pool salt system and is ultra reliable. Let me know in the comments what system you like and how much you love your Jandy salt system.
Stay tuned for more videos!
Support me on Patreon: / chlorineking
Also, check out my friend Robert at Clean Pool & Spa and subscribe to his channel! www.youtube.co....
www.chlorinekin...
www.chlorinekin...
www.chlorinekin...
www.routely.net
www.riptidevac...
![🎤 ไปกันต่อออ! จับฉลากร้องเพลง x P’ #XXSIVK [EP.2] (1/2) เพลงของใครจึ้งสุดน้าา 💓🎤 #MXFRUIT](http://i.ytimg.com/vi/mLI_K0sAS4o/mqdefault.jpg)
Great video.. Any idea how to fix my Sandy TruClear panel? My panels buttons don't do anything. It turns on and says it's chlorinating at 70%, but I can't raise or lower or power it off with the button. Is there I hard reset that might fix it?
Is it connected to automation?
awesome video King Pool Service - When you say not having this system running while pump is off - After installing the iAquaLink automation, as soon the pump is off, the Salt system shows "Standby". May I understand it should be completely off? Thanks!
If wired properly then the the relay should cut power to the system completely. Are you physically putting it in standby mode or is it doing that on its own?
@@ChlorineKingPoolService I believe the Salt TrueClear system is not connected to the iAquaLink realy to shutdown the system completely. As today, the TrueClear when the pump is not running, it shows "Standby" (nope, I don't put in this mode), and when the pump is on, the TrueClear shows "Chlorinating %".
Could you explain to me what the days setting is and what they should typically be set at?
Just recently had to shut down our pool, drain it, and change the liner. Once we turned everything back on the screen on our Jandy TruClear salt water system is blank. What can we do to troubleshoot it?
My Jandy Truclear Pro series panel says No Flow, even when it's running. I cleaned the cartridge filter. I also turned on the pump without the cartridge just to make sure that wasn't the problem. Pool seems to be circulating good. What causes the NO FLOW signal.
More than likely the flow switch is bad. I’d contact your installer and they should get a warranty station out there ASAP.
I can't get the generator which is hooked up to Aqualink to get off standby. Cannot manually operate the generator even in Service mode. Can't get it off of Standby to generate chlorine. Turned off a couple times hoping that it would reset but it just goes back to standby. Any help on this would be appreciated. I think the system is still under warranty.
It sounds like a bad power center to me. Before you spend money on that though it may be worth to have your installer come out and disconnect the 485 comm cable from the power center to see if you can turn it on separate from automation. That would mean possibly a bad 485 cable, automation board, etc.
This system is the best system hands down. Works like a tank
I really enjoy installing these!
Any recommendations on a tester for checking the salinity of our pool water? Secondly, our pool is about 11,000 gallons. Any recommendations on what chlorination level to start out with? Thanks!
We've had decent success with Salt Dip Pros
@@ChlorineKingPoolService thanks so much!
@@kevinbriggs2611 you’re welcome.
I just installed the Jandy Tru Clear system and it has a lot of extra cable between the Cell and the Control Box. It cam with a lot of control cable like 10 ft and my cell is only 3 ft from the panel. What do I do with all the extra cable? Thanks
I usually just roll/wind it up and zip tie it to the conduit somewhere so it’s secure. Also off the ground so rodents/squirrels can’t chew on it.
@@ChlorineKingPoolService Okay, I just wasn't sure if it would cause any kind of problem. Thanks
Not at all. Enjoy it and you’re welcome.
New pool owner here what does it mean when it says cleaning on screen ?
It’s reversing polarity and trying to clean off the cell blades for you to prevent build up.
Haven't turned on my pool heater yet because its still cool outside. I have been cleaning the pool everyday though. At what point do i take it off Standby mode and switch it to Chlorinating? Also at what % do i set it at. I have a 16x32 inground pool.
You can really turn the cell on anytime you want. If the water is really cold you can try 40% as you don’t need as much chlorine in the colder waters, and once it’s summer time you can play with 60%-80% to get the desired chlorine output you’re looking for. There’s a lot of variables to nail down a certain percentage so use whatever percentage that gives you a consistent 3-4ppm.
Any troubleshooting tips for a Jandy Tru Clear that won't power on?
We just got our system, and no matter what we do we get a low flow error. The flow is good, cleaned the filters etc. still get a low flow error any ideas on the issue ??????
Please explain the days. Mine says 5 hours 0001 days and I can’t change the days
What does the “days” reading represent in the menu?
How frequently it does self cleaning.
Does this kick on when it detects flow of water? Or does it have to be wired to the pump?
Has to be wired with the pump. The once powered it will sense flow. If no flow then it doesn’t produce. If it detects flow then it will. I hope that makes sense.
I am not connected to an iaqualink system. How do set the chlorination level to 30% (as an example) permanently? Currently I set the level to 30% (as an example) but once the unit turn off (pump turns off) and then back on, chlorination goes back to 100%.
But if you have automation where on iaqualink can I set up CYC? Please help.
My mind must be shot? What is CYC?
On your videos 2 actually you show how you push the up and down arrow for 6 seconds on the TruClear and access settings and you spoke of reverse polarity and how the default is 5 hrs and the CYC can be changed from 5 hrs to 3 hrs. BuT if you have automation you can't do it on TruClear and instead have to go to iaqualink. And your screen shot shows set acquapur. But all I see in that menu item is pool % for chlorine, spa % for chlorine, boost. And timer for boost. I can't find anywhere in iaqualink where I can set up reverse polarity time.
I am getting snow flakes and will clean saltbcell trow but also wanted to add cyc or look to see if it was set. But can't on TruClear bc I have automation. I even Valles iaqualink they don't know what I am talking about.
Oh that haha. Sorry it’s been a long week.
To my knowledge you can’t alter that through aqualink. All you can change through iAquaLink is the output percentage. It’s best to disconnect the 485 and change it on the power center itself, then reconnect to automation.
If you’re having flakes that’s calcium phosphates. I’d turn the salt system off for 1-2 weeks, get the phosphates under control, then slowly reintroduce the salt system to your pool. Also keep the ph down on the lower acceptable range and if you run the heater keep the temp down a bit. I hope this helps.
@ChlorineKingPoolService is calcium phosphates different than phosphates on my leslie water test bc that is very low almost negligible. My ph is always around 7.4. Don't use the heater. And have no clue what u mean disconnect the 485.
Any idea why the system wouldn't turn on at all ?
Is the a video on the connectivity to the Aqualink? I just switched from the old system to this one. Some of my concerns…1) I lost measure. Do you know if the low salt alarm is presented in the aqua link system. I don’t like that when connected to aqua link the Trucell display does not read the chlorine.
No I don’t have a video of that yet. Yes you lose the measure of salt in iAquaLink. That is reserved for the aquapure. Low salt should be displayed on the truclear power center only. To my knowledge neither system reads chlorine unless you mean slat content.
I just watched this video again, and wouldn’t happen to have one on how you wired this system up to the Aqua link? Your second take on the video indicates the system is chlorinating and connected to aqua link. Mine is connected to the aqualink, but it does not display what I have programmed into the application
You should be able to control the output of the chlorinator but the salt reading is only compatible with the aquapure.
@@ChlorineKingPoolService I agree, that I should be able to indicate the system is chlorinating, but when activated by the aqualink it does not appear to me, that is is overriding the standby switch on the Truclear. In your video, 2nd or 3rd frame, the display shows your system to be chlorinating while controlled by the aqualink
How can I see salt level on this ???
You actually can’t on this system. It’ll give an alert when it’s low salt. Thanks for watching.
Can you connect to wifi
@Chlorine King Pool Service I can't get the generator which is hooked up to Aqualink to get off standby. My chlorine levels are presently nil. It used to be at 50%. I was told to increase to 70% to get my chlorine levels up. The only thing I could do through Aqualink was to do a quick boost. It does not automatically go back to 50%. It goes back to stand by. Please help. No one knows what I can do
So I’m dealing with this exact issue with a warranty claim I’m doing for another client. We replaced the power center and it’s still doing the same thing. So my TSR coming out to see if he can figure out something I’m missing. Once that happens I’ll try to remember to post here. Im sorry I don’t have a better answer.
Did you get your issue fixed? Mine is doing the same thing. I think it is still under warranty
How can I see the salt level parts per million off of this setup? Having a hard time and mine keeps on reading low temp low salt
Unfortunately that’s not a function of the truclear. You would need to get a secondary meter such as the tracer to test salt.
When I run my system in manuel. Pump on , the truclear screen sometimes goes blank, but still lit up, and always in standby mode, i have to push power button to get to chlorination mode , switches from waiting to chlorination all the time. But at nite when it runs in auto schedule its always chlornating . Thanks
Confirming it’s hooked up to automation?
@@ChlorineKingPoolService yes its all programmed with iaqualink, but when i put in service mode to run it manually , it truclear displays random, waiting, chlornating, standby, sometimes blank. Maybe the phoenix hot sun doesnt help
What’s the real difference between this and the AquaPure series? Say AP1400/
The Aquapure has an external flow/temp sensor in addition to a power center that has a little more information such as cell reversing, etc. It is also rated for 40K gallons I believe whereas the truclear is rated for 35K. If hooked up to automation you will not get a salt reading with the truclear, where as with the Aquapure you will. Hope this helps.
@@ChlorineKingPoolService awesome, so it should be a better system. It’s what my PB is installing.
@@guillermomartin8248 great. I do prefer the system personally. I also like how you can see when the blades are dirty. It's a nice touch.
Just got ours installed. It stays on 100% chlorinating and buttons dont respond. Any guess what could be wrong?
Do you have automation?
Anyone know how long it takes to show No Flow when the pump goes off? My Truclear keeps generating chlorine when pump is off and doesn't show no flow.
I think it takes about 20 seconds before it will flash “No Flow.” At least that’s how mine is.
What are your thoughts on a rola chem are they good for sanitizing your pool
Never used their products to be honest. I wish I could give more help!
Thanks for your honest opinion
Hey man, not sure if this is the best place but I am having an issue with a clients cell that is really leaving me stumped. Everything that would be the issue is fine. The cell is only producing enough chlorine to sustain 1.5ppm of chlorine per week. cya is 80. PH 7.4 alkalinity 60. Salt 3000ppm. No error codes, anything. Cells clean as a whistle. It's a Jandy Aquapure. What could be the issue?
How old is the system? The cells have a ruthenium coating on the blades. Once that wears off the cell won’t work properly. How big is the pool? Phosphates? Percentage of production?
Only 8 months old. Pool is 22,000 Gallons. And it only does 1.5ppm regardless of percentage. 10% or 100%. It does have phosphates but it was never an issue before. Cell shut down over the winter as normal, but now the temps are above 70, and this is all its doing.
How about the pump runtime and the cell model? It may be a undersized cell or the customer may be guilty of cutting pump off. 🤔
@@Mendelevius Also, I agree phosphates aren't always an issue, but if you are having issues, it is a good place to start. Is the pool producing white or blue flakes?
@@Mendelevius sorry I'm bored right now, with a cya of 80, your alkalinity needs adjusted. If cya is above 60, take 1/3 of cya, subtract from alkalinity to get your Total Corrected Alkalinity(TCA). 60-27=33. Your alkalinity is 33, with a 22k pool about 16lbs of bicarbonate is needed to bring you up to TCA of 70ppm
You should have mentioned Turing it off when adding salt and how long to wait before turning it back on.
Yes I should have and great point!
So how long?