Whats Wrong with my $100 Phazer --- Carb and Engine Teardown

แชร์
ฝัง
  • เผยแพร่เมื่อ 27 พ.ย. 2024

ความคิดเห็น • 47

  • @SuperRj189
    @SuperRj189 2 ปีที่แล้ว +1

    Other than the fact your lighting is poor, this is one of the best resurrection videos I’ve seen on this fantastic engine. I especially enjoyed the carb section but oh….. I wish you had a four foot led light just overhead!

  • @jordanengdahl4418
    @jordanengdahl4418 4 ปีที่แล้ว +4

    Is it ported/ shaved heads? I've heard the crank becomes the weak point if you go beyond modding the pipe and intake on these. Also, I noticed the Welch plug behind the idle fuel screw on those carbs is siliconed over. Very likely someone removed the plug to drill out one of the small holes to enrich the mid-range for that pipe. If I remember correctly PSI recommended drilling the rearmost hole out with a number 56 number drill. I did this to a pair of carbs this winter and am pleased with the results. Good luck with those crank bearings. They are a bit difficult but doable.

  • @shaneworster1682
    @shaneworster1682 3 ปีที่แล้ว +1

    Haha I had a phazer once was locked up solids got the top end free but the rods were frozen to the crank I soaked it for days never got it free had the motor out and had it soaking pulled the carbs and they looked worse than the set u said we’re the worst I had ever seen the pic for the float had rusted away plastic floats were just gone so hot rid of that one

  • @96Duelfuel
    @96Duelfuel 3 ปีที่แล้ว +1

    I have one that the baffles are broke in. Still works...

  • @seanyboy650
    @seanyboy650 3 ปีที่แล้ว +3

    I have the exact same bottom end problem on my 1991 Phazer 2, what did you end up doing to fix it? Seems I can find individual parts only from Yamaha but no crank assembly's are being made anymore.

    • @ogiegloa
      @ogiegloa 3 ปีที่แล้ว +1

      Following. I have a ‘91 Venture, same engine and same problem.

  • @hulk369852147
    @hulk369852147 3 ปีที่แล้ว +1

    I just got one been sitting a while but in a barn from a old farmer with only 3000 all original miles I have cleaned it up got it running went out few days later started it up now its running but bogging down so I'm going check for air leaks and clean carbs better but in the mean time I started hearing what I think is the same clunking. Do you have a video on how you fixed it. I parked it cuz I don't want to damage anything.

    • @hulk369852147
      @hulk369852147 3 ปีที่แล้ว

      I'm using wife's TH-cam account just so ya know trying look up ways to fix this without damage

  • @brianbenz3613
    @brianbenz3613 2 ปีที่แล้ว

    I would see if there's any rusty water lines on the Crankshaft because it may have been sunk in a lake and the crank bearings will start to make noise if they got rusty

  • @coopersand1804
    @coopersand1804 3 ปีที่แล้ว +1

    Trying to get mine going. Electric start won’t crank, just clicks on the solenoid by the battery. New solenoid?Pull start fires it but it won’t stay running without shooting carb cleaner in it.

    • @adaminthemitten8940
      @adaminthemitten8940  3 ปีที่แล้ว

      I had to put new brushes in my starter motor to make it work, I could put power directly to it and it wouldn't crank. Might be something to look at

  • @toddjacobs5660
    @toddjacobs5660 3 ปีที่แล้ว +1

    Call Japan n ask if they have a new set of carbs

  • @96Duelfuel
    @96Duelfuel 2 ปีที่แล้ว

    Need to make a vid on starter replacement

  • @karldeman3125
    @karldeman3125 3 ปีที่แล้ว +1

    the sound comes from the gears in the oil pump

    • @purplepurpleism
      @purplepurpleism 3 ปีที่แล้ว +1

      Man, i have been trying to figure out that noise for forever.

  • @ArcticJeff
    @ArcticJeff 4 ปีที่แล้ว +2

    Wow, I've never seen a crank do that. Must be a broken crank pin?
    Have you ever tried degunking a carb with Pine-Sol? It works really well. I use it for all my carb cleans. Its safe on rubber and even rejuvenates rubber bits. Just don't use it on chrome plated parts like slides.
    advrider.com/f/threads/the-pine-sol-degreaser-thread.560117/

    • @adaminthemitten8940
      @adaminthemitten8940  4 ปีที่แล้ว +2

      Yeah I haven't gotten it torn apart but it must be broken or something froze in there and broke something. I've never tried that stuff but I'll give it a shot on my next set!

  • @ArcticJeff
    @ArcticJeff 4 ปีที่แล้ว +1

    Sled season is approaching...got any updates?

    • @adaminthemitten8940
      @adaminthemitten8940  4 ปีที่แล้ว +1

      About 90% done with the new build, just going to make it one video. Should be out early next week

  • @25maroneyable
    @25maroneyable 4 ปีที่แล้ว +1

    Where do you look for sleds at? Everywhere I look everyone wants an arm and a leg for them.

    • @adaminthemitten8940
      @adaminthemitten8940  4 ปีที่แล้ว +1

      Found this one on the side of the road. Plus I always try to do my buying in the spring when theres little demand. But I see the same thing, it's pretty normal for people to want $1000 for these things

    • @25maroneyable
      @25maroneyable 4 ปีที่แล้ว

      @@adaminthemitten8940 lucky you, I always got my eye out for them. I live in houghton lake, lots of snowmobile trails here. I got my first sled this year and im praying for some snow right now lol.

    • @adaminthemitten8940
      @adaminthemitten8940  4 ปีที่แล้ว +1

      @@25maroneyable yeah my job has me driving all over the thumb so I have a lot of time to look. We just got enough snow on tuesday I got to ride the ditches for a night, but yeah I'm hoping for some snow too

    • @25maroneyable
      @25maroneyable 4 ปีที่แล้ว

      @@adaminthemitten8940 right on, I used to live in marlette. You should come up to tip up town, they have sled races and vintage sled shows.

  • @dathanschuch3294
    @dathanschuch3294 3 ปีที่แล้ว +1

    I have a question I’m about to buy a really clean phazer 2 from a friend and I’m looking for oil, do they have power valves or no because the Polaris blue oil is made for fan cooled non power valve motors and I don’t wanna buy it if it won’t work

  • @engine_headpro8127
    @engine_headpro8127 3 ปีที่แล้ว +1

    a question, is it possible to put a 1.75 inch lug track in a old phazer

    • @brianhouts
      @brianhouts 3 ปีที่แล้ว

      A couple guys have videos floating around on here putting bigger lugs, looks like 1 3/8 is the max with minimal rubbing. Others have fitted thicker lugs after convincing the tunnel to share some space with the engine.

    • @engine_headpro8127
      @engine_headpro8127 3 ปีที่แล้ว

      @@brianhouts ok thanks

    • @user-bd5md5cm2j
      @user-bd5md5cm2j ปีที่แล้ว

      Change your driver's from 8 tooth to 7. You can get that track on. Gears it down a bit too Wich helps with he power. I'd use a better secondary or put a roller clutch on it. They have a tendency to not shift correctly in stock form

  • @coopersand1804
    @coopersand1804 3 ปีที่แล้ว

    Trying to get mine to run. Fuel pours out of the muffler when I try to pull start it. Fuel pump?

    • @adaminthemitten8940
      @adaminthemitten8940  3 ปีที่แล้ว

      I would check the floats in the carbs first, sounds like they are stuck and just continually pouring fuel in

  • @karldeman3125
    @karldeman3125 4 ปีที่แล้ว +1

    more please

  • @starfoxnerd88
    @starfoxnerd88 3 ปีที่แล้ว

    Sick

  • @melindakendall2868
    @melindakendall2868 3 ปีที่แล้ว

    hey does any of your phazers leak oil when they sit

    • @adaminthemitten8940
      @adaminthemitten8940  3 ปีที่แล้ว

      Yes, if the oil lines are older and hard they usually leak

    • @melindakendall2868
      @melindakendall2868 3 ปีที่แล้ว

      @@adaminthemitten8940 ok cause we have one that leaks oil when it sits but not when its running they say the phazers do that

  • @gallupcustomknives2293
    @gallupcustomknives2293 3 ปีที่แล้ว +1

    I hope you threw those carbs in the trash and put a couple mikunis on it

    • @brly4542
      @brly4542 3 ปีที่แล้ว +1

      Phazer do use Mikunis, but it's a butterfly design not flat slide

    • @gallupcustomknives2293
      @gallupcustomknives2293 3 ปีที่แล้ว

      @@brly4542 the crappiest mikuni ever made. Yamaha went to mikuni and asked them to take tried and true design, throw it in the trash, and make an enlarged lawnmower carb just for them, and that’s what the result was lol

    • @SuperRj189
      @SuperRj189 2 ปีที่แล้ว

      They are Mikunis.

  • @jeffreyhagelin3672
    @jeffreyhagelin3672 10 หลายเดือนก่อน

    What do you expect for one hundred bucks 🤔 ?

  • @mmjoo5579
    @mmjoo5579 4 ปีที่แล้ว +1

    when the new video comes

    • @adaminthemitten8940
      @adaminthemitten8940  4 ปีที่แล้ว

      Hopefully by the end of november or early december, getting parts together for the new build

  • @KAZT4R
    @KAZT4R 3 ปีที่แล้ว

    PZ480 YAMAHA Good-⤴️⤴️

  • @ups3357
    @ups3357 4 ปีที่แล้ว +1

    First