Classic Mini Workshop - Project Sprout Pt.14 - Outer Sill Removal & Replace
ฝัง
- เผยแพร่เมื่อ 16 ต.ค. 2024
- Please consider subscribing to keep up to date with the latest videos and content. Thank you for the likes and comments, it is greatly appreciated.
Find me on Facebook / classicminiws
Here it is, the new project Mini. Found on E-bay but I lost the auction only to later find the higher bidder messed the seller around so it was offered to the next highest bidder...... Me. The Mini is a 1997 Rover Cooper MPI and has been off the road in a garage since 2007! It's what some might call a barn find.
In this update I finally get stuck in and start addressing the rust and corrosion. I remove the floor pan soundproofing and straighten the dented floor before cutting off the outer sill and corroded sections of the inner sill in preparation for replacement.
Music: Tobu & Itro - Sunburst
/ tobuofficial
/ officialitro
Released by NCS / nocopyrightsounds
"Wanderlust" by Declan DP
bit.ly/2HT70xF
Attribution 3.0 Unported
creativecommon....
You have a good calm methodical approach to the project....a sure recipe for enjoyment.
Wow, if only some of the other Projects were as good as Sprout in comparison with the cills. Great video as usual!😎
Looking good Corn Beef. Good to see original sills rather than botched sills
Hi Keith,great start to the project and viewing the work so far you make it look so easy and always have a good action of plan.Cant wait to see what the other side is like.
Very much enjoyed that video Keith, it reminds me a lot of my sidewalk that was similar with inner sills repairs and some sills etc. Looking forward to seeing more 👍
Great to see another video. Been watching them all day lol. We have just got a 1981 mini project for out selves. 1 good thing is a lot has been done already like all the welding. We know it has been done right has we got the car off the wife's father which i have been helping with the work. Again great work.
Now the fun begins. I've been eagerly awaiting this part:-)
This was good to see - I'm about to start replacing mine and I thought it wasn't salvageable, but it looks better than yours did so it should be fine! :)
Great work! I think... and thats just me, that you you make you make the right decision when you keep as much original panels as possible. The patches in the innersills will not be seen and covered. Keep up the good work. Best regards from Mikael, in the north of Sweden 👌
Thank you. Yes the welding will be very neat anyway and not really visible
Good neat job
Mark Gutter thank you
Bravo well done smashingly amazing work
Thanks Garrick
Keith, Looking at the outer sill you would think the inner would be far worse than it was, It seems like each bad
rust of area was in between the flutes where the condensation will sit. Cheers Dave
Yeah, it was just the bits between the flutes. The sill came off so easy! I've just looked at the other side and I don't think it's as bad
Great video. I do like your rust detection tool, is this available on your TH-cam shop?
Nice work. What's your thoughts on using gasless coreflux wire ? Personally getting tired of getting through gas bottles ...
Never tried it but I’ve yet to see a nice weld when using one. Possibly a bit better if welding outside in the wind? The wire is also more expensive and if you get the bigger bottles of gas it’s not so much cheaper
Works going well, but put a knob on the gearlever before you poke your eye out!!!
LOL, good point
What is the liquid blue that you put after removed the rust ?
It's a product called Kurust which neutralizes rust
@@classicminiworkshop thanks ! I am doing the same to my car.
I beat my floor out like that and all the filler fell out 😂🤣😂
LOL :)
Oh the mess 😱
Why not replacing the whole outer sill?
This is so fiddly and leaves lots of ongoing rusting surfaces!
I did replace the whole outer sill on both sides? Did you mean the inner sill?
I hate rust. You think you've got a small hole then it gets bigger the more you poke at it.