Thank you for the video... I got a lot of help from a couple of the comments below...like pressing the Prewash button to advance from C5 to C06 and it continued just fine. Also to the lady that posted the steps of Drain Spin, No Spin, Then the Prewash button within 12 seconds to start the Diagnostics. I love TH-cam. My HE3T was leaving my. clothes sopping wet...only 3 coins in the trap...going to try a small load of the rags I used to clean up after checking the trap. Wish me luck.
My He3 does not get passed c01, once it gets to c01 it stops and starts flashing FH. The inlet water screens were clean, it does fill up when I do try to do regular wash. my pressure switch works and there is no crack in the hose and the air trap is clean. My water flow device spins freely, it might be that the sensor on the water flow is faulty but i do not know how to test that, yet I dont think that is that is the problem.
Mrs Doyle, My HE3T has been stuck endlessly on c:05 I replaced the pump and cleaned the drain and supply line. What was the Fix? PS were you getting the SUD and then F2 code..? That's where I am stuck. Anything you can remember please.
I have a Kenmore elite HE3T Steam, The issue I am trying to figure out is why it will not do a clean washer cycle. I have tried to get into the diagnostic mode several time and it does not enter the mode. the machine is 5 years old and has had the CCu replaced this year and two pressure sensors over the past two years. any help would be appreciated
Question: What are we expected to see during each test (ie. Pass or Fail, how do we know?). If it doesn't go from 1 test to the next test after several minutes is that what we're looking for as a Fail? Also, appears these instructions also work for the HE4(t) model Kenmore Washing machines too.
I have the Kenmore Elite HE3T. I cleaned the drain trap and ran a couple of other steps as directed. But, it still failed with F 06. I ran diagnostics and on step 4 it made a loud clicking/rattling noise. I ran the diags again and no noise. Now it's working.
Mine is doing the same thing but it won't make it past 04....it's been noisy(it's actually my moms of course I've gotta fix it for her now lol) for a few months I guess....kinda a bad motor sound she's said
My girlfriend says she thinks she lost a bra underwire in the laundry. I was wondering if that found its way somewhere it shouldn't have been and worked itself out but, I haven't seen it.
Ours is either the motor (what I'm banking on) or a bearing gone out.... It def won't hit spin cycle.....well....after a few hours on TH-cam and google I think I'm good too go as far as taking the entire thing apart and fixing anything that's wrong with it lol.... Gotta live good ole TH-cam university
Hello I ran a test on mine it was stuck on c:05 for a while then it began again finished all the codes. The clothes clean light is on and door unlocked. What does this mean?
door on my front load computerized kenmore wont open after a load of wash it takes 2 days to get it to open by that time it has an odor.what could cause this
I'm working on same model and washer client is telling me that every time they are goin to start a cycle they have to unplug unit and re-plug to start I'm coming to being a door switch or could it be Ccu thanks
Mine got stuck on F5, I don’t see any response or help here for that..... after that I pushed the stop button ⏹ and the last message came saying FU.... I guess it’s time to replace the washer..... 😂
Susan DeNagel c5 is a heater test.. some models dont have it but the test mode is universal for a models.. just press pre wash to manually advance from c5 into c6 and it should continue into it finishes in c8
Would you please give me the steps on how to do the diagnostic test on the HE3t washing machine, please??? I've been struggling to figure this out for more than a week. Thank you, Super Frustrated Single Mom...HELP!!
I'm sure you already dealt with the problem by now but for anyone watching this video recently: 1) Push the "drain/spin" button. 2) Set the spin speed to "no spin". 3) Push the "prewash" button 4 times. The display will show C:00 and begin the diagnostic test.
It may also screech if there is a hole in the bellows that goes between the washer tub and the door. If rocks or coins go through the washer sometimes they can rip a hole in the bellows. It's not that bad to replace it yourself though.
@@84regalboi81 It looks like it should only go a short time. Mine kept going indefinitely on C05. One of the other comments noted if C05 continues, you can press prewash to get it to advance to C06. I did that and the first time it didn't advance. After waiting about 10 to 15 seconds, I pressed prewash again, and it immediately switched to C06 and started draining. Then it went through all the subsequent codes promptly and after completing C08, it just stopped and turned off.
Thank you for the video...
I got a lot of help from a couple of the comments below...like pressing the Prewash button to advance from C5 to C06 and it continued just fine. Also to the lady that posted the steps of Drain Spin, No Spin, Then the Prewash button within 12 seconds to start the Diagnostics. I love TH-cam.
My HE3T was leaving my. clothes sopping wet...only 3 coins in the trap...going to try a small load of the rags I used to clean up after checking the trap. Wish me luck.
I followed the steps and found the problem. Really appreciated!
Thanks VERY much for this video. It was very helpful - it's nice to know it is specifically the COLD water inlet that is not working!!
My He3 does not get passed c01, once it gets to c01 it stops and starts flashing FH. The inlet water screens were clean, it does fill up when I do try to do regular wash. my pressure switch works and there is no crack in the hose and the air trap is clean. My water flow device spins freely, it might be that the sensor on the water flow is faulty but i do not know how to test that, yet I dont think that is that is the problem.
What if I can't get it into diagnostic mode?
mine won't get off C05 it just stays on C05 why won't it go to C06
Mine is the same
What does this mean?
The diagnostic mode process will take up to 30 minutes so CO5 will take up to 30 minutes
Mrs Doyle,
My HE3T has been stuck endlessly on c:05 I replaced the pump and cleaned the drain and supply line.
What was the Fix?
PS were you getting the SUD and then F2 code..?
That's where I am stuck.
Anything you can remember please.
I am running a diagnostic on my HE3t, and it is stuck on C:06. What should I do?
I have a Kenmore elite HE3T Steam, The issue I am trying to figure out is why it will not do a clean washer cycle. I have tried to get into the diagnostic mode several time and it does not enter the mode. the machine is 5 years old and has had the CCu replaced this year and two pressure sensors over the past two years. any help would be appreciated
Question: What are we expected to see during each test (ie. Pass or Fail, how do we know?). If it doesn't go from 1 test to the next test after several minutes is that what we're looking for as a Fail?
Also, appears these instructions also work for the HE4(t) model Kenmore Washing machines too.
Exactly, mine didnt go past the C:02 test and started making a noise.
So if it goes through all the codes and finishes, does that mean it's okay? Problem resolved?
I have the Kenmore Elite HE3T. I cleaned the drain trap and ran a couple of other steps as directed. But, it still failed with F 06. I ran diagnostics and on step 4 it made a loud clicking/rattling noise. I ran the diags again and no noise. Now it's working.
JB sparks no issues since?
Mine is doing the same thing but it won't make it past 04....it's been noisy(it's actually my moms of course I've gotta fix it for her now lol) for a few months I guess....kinda a bad motor sound she's said
Hi, no, the noise happened one more time but I haven't heard it since.
My girlfriend says she thinks she lost a bra underwire in the laundry. I was wondering if that found its way somewhere it shouldn't have been and worked itself out but, I haven't seen it.
Ours is either the motor (what I'm banking on) or a bearing gone out.... It def won't hit spin cycle.....well....after a few hours on TH-cam and google I think I'm good too go as far as taking the entire thing apart and fixing anything that's wrong with it lol.... Gotta live good ole TH-cam university
oh and it has plastic pieces in drum when it finished diagnostic. could it be the front outer tub?
Hello I ran a test on mine it was stuck on c:05 for a while then it began again finished all the codes. The clothes clean light is on and door unlocked. What does this mean?
door on my front load computerized kenmore wont open after a load of wash it takes 2 days to get it to open by that time it has an odor.what could cause this
When stuck on 06 is the water dropping?
I'm working on same model and washer client is telling me that every time they are goin to start a cycle they have to unplug unit and re-plug to start I'm coming to being a door switch or could it be Ccu thanks
Mine gets an FH code in C00 while filling up. Must need new flow meter.
UP ALL NIGHT-SLEEP ALL DAY!
Could it mean that my CPU is having a problem communicating with the machine?
Getting a F15 code what do I do?
How much water is the washer supposed to have in there while washing anyone know?
Mine got stuck on F5, I don’t see any response or help here for that..... after that I pushed the stop button ⏹ and the last message came saying FU.... I guess it’s time to replace the washer..... 😂
where can i find what the dia codes mean?
Mine passed the diagnostic but won't start when i try to wash?
Mine gave f02 cleaned drain was fine now said sud then wont turn off or drain.
While running a diagnostic on my HE3t it is stuck on C5 and continues to spin clockwise with water in tub, why won't it advance to C6 and drain out ?
Susan DeNagel c5 is a heater test.. some models dont have it but the test mode is universal for a models.. just press pre wash to manually advance from c5 into c6 and it should continue into it finishes in c8
Thnk u very helpfull
Thank you. .very helpful
Where are ur results for each test?
What year is that
My washer is doing the same. It is stuck on C;05 wont move forward
Would you please give me the steps on how to do the diagnostic test on the HE3t washing machine, please??? I've been struggling to figure this out for more than a week. Thank you, Super Frustrated Single Mom...HELP!!
I'm sure you already dealt with the problem by now but for anyone watching this video recently: 1) Push the "drain/spin" button. 2) Set the spin speed to "no spin". 3) Push the "prewash" button 4 times. The display will show C:00 and begin the diagnostic test.
What does f 11 mean
mine didnt go past the C:02 test and started making a noise.
Hello! How did you fix the C:02 problem? The dial keeps turning and clicking
so what if you have a he3t with no steam whats the button u press 4 times
Prewash
I need to run a diagnostic test on my life
Kenmore elite HE3 dryer screathcing how do I fix it?? HELP
"screathcing" like a jet airplane sound when in the spin cycle? If so, then bad bearings
It may also screech if there is a hole in the bellows that goes between the washer tub and the door. If rocks or coins go through the washer sometimes they can rip a hole in the bellows. It's not that bad to replace it yourself though.
Anyone have a list of the c codes?
Sounds like your heater is not closed....you may have a OPEN heating element.
How long is c05 suppose to go for
Did you ever get an answer for this question
@@84regalboi81 It looks like it should only go a short time. Mine kept going indefinitely on C05. One of the other comments noted if C05 continues, you can press prewash to get it to advance to C06. I did that and the first time it didn't advance. After waiting about 10 to 15 seconds, I pressed prewash again, and it immediately switched to C06 and started draining. Then it went through all the subsequent codes promptly and after completing C08, it just stopped and turned off.
If my kepte he3 won’t power on
does any know what F35 is
anyone else get a headache from the bass on that music??
sounds like cpu....try bypassing door switch
Thank you
3:37
Shut the radio off and use your words.