Easy Valve Adjustment on Yamaha WR450F
ฝัง
- เผยแพร่เมื่อ 6 ธ.ค. 2015
- 🤗 Welcome to Vegas RoManiac Channel 🤔 U Ever wondered what I use when I ride or fix my bike !? 🤨
😍 I ride on this Knobby REAR TIRE - amzn.to/2MQm5lM
😏 I ride on this Knobby FRONT TIRE - amzn.to/2NOmXEa
😲 My favorite Tire mounting compound - amzn.to/2NNH999
🤩 My favorite motorcycle tie-downs - amzn.to/1ifGRaa
😀 My favorite air filter for the money - amzn.to/2QaKRLI
😃 My favorite Oil Filter - amzn.to/2QaLd50
😉 My favorite Magnetic oil drain bolt - amzn.to/2Q6McTO
😘 My favorite Micro Car jump starter - amzn.to/2MQmQv8
🤗 For more items you can visit MY STORE ON AMAZON 🤗
👉 www.amazon.com/shop/twowheels... 👈 - ยานยนต์และพาหนะ
You should measure each valve and set them more toward the loose side not the tight side like you did because they tighten over time not loosen.
Excellent instruction! Thanks for your clear and concise video!
This is a really good video, your great at explaining things clearly. cheers mate.
Great video. This will help me a lot when I do my valves.
I think I can do some things but you and MrDuhfactor take the mystery out of how to do it right. Thanks
Cool video. I'll probably be doing this next year on mine.
that was really helpful thx man
Well done dude!!! Especially with your non dominant hand!!
shim bucket dude 😆 nice video man.
Good video but you should have measured each valve to have true numbers on each.
I've been putting off the valve adjustment on the klr for a while. Very intimidating. Needs to be done though, just turned 15000 miles.
Twistygrip One you get the cover off, it's not that bad. There's just a lot of interferences and it's a tight space in general.
Thank you, I am hoping that I can adjust my valves and not rebuild my top end. Great video
Hi, you don't have engine in TDC??
Are those valve clearance specs good for a 2003 wr450f?
Shouldn't you have a Velcro brace of some sort. Let that wrist get better.
Good to see your ok overall!
i need info bout wr 450.
i have wr 450 2003 road legal, i didnt drive it for 6 months, now when i start him, it drives ok and bla bla, but gas leaks from bottom of carb, and after few mins of driving bike stops, and sometimes chokes, is that normal for 6 months of not driving, i believe carb and gas tank after that time, all dirt fall into carb and at bottom of tank.
so that is only problem of gas leak and choking and stopping bike
Your carb needs cleaning bro. The gas leaking from the bottom means that the float is stuck (or at least the needle is stuck). It's kinda normal, especially if you didn't use stabilizer. The ethanol in the gas will leave a varnish in the carb, clogging the jets and gumming stuff up. :-( ethanol sucks...use straight gas if you can, at least before storing it!
so i have a quick question. Im trying to adjust my valves. how much pressure do you put on the feeler gauge? how hard do u push it?
+MΣNT0R™ not hard, hard to measure, but if you push it and it bends its to hard. The only thing k I can think of, is not harder than closing a zip tie.
The feeler gauge should feel like you are pulling scotch tape off of the roll.
that'a a great analogy
Its a wr 450 f 2011?
08
missed the part where he said to have the piston at tdc. or cam lobes opposite of valve shims. WHEN YOU START.
Each bike it's difrent, the wr that has the regular motor not the inverted piston, it's exactly ass stated, you have dots on the cam. Sprockets to align with tdc.. I sold that bike can't redo the video and the new yz250fx I have now, it's exactly the opposite
Happening tomorrow on my bitch 👍 got the owners manual aswell wich describes it on like 7 pages 😂
I think I am a bit scared to do this myself. Many "verv very important" things.
Man, it's so easy after you do it twice, first time my hand was shaking
It’s actually pretty easy, I just sanding down my shim with 180 sand paper. I went from 1.85 to 1.45. Exhaust on YFZ 450 is .010 and Intake was .004
Certainly not for a rookie like me