Solving Bandsaw Dust Collection - With an Unnecessary Walnut Door!
ฝัง
- เผยแพร่เมื่อ 28 ก.ค. 2024
- I made a new walnut door for my bandsaw so I could hook up my terrific Oneida dust collection system and solve the dust collection issue on that tool once and for all.
Oneida: www.oneida-air.com/
Oneida V-System: bit.ly/3KsZVlB
Shop Plan Design Service: bit.ly/45l9w5I
TOOLS & MATERIALS:
As an Amazon Associate I earn from qualifying purchases. (shopping using these links helps support my channel & costs you nothing)
Dust Inlet Flange: amzn.to/3tiHBWH
Table Saw: amzn.to/3zCifTx
Miter Saw: amzn.to/46flVcA
Pin Nailer: amzn.to/3AI0eDz
SurfPrep Sander: bit.ly/3KFtL6J - Use Code gunflint10
Starbond Glue: bit.ly/2EjSRpC - Use Code gunflint15
Drill/Driver Set: amzn.to/3mg0tSR
Jointer: amzn.to/45gZxid
Planer: amzn.to/3snLnNZ
Trigger Clamp: amzn.to/3zX8zmH
Wood Glue: amzn.to/3JrOkCX
Affiliate Discounts:
SurfPrep Sanding: bit.ly/41aGXWC
10% off code - GUNFLINT10
Montana Tools: bit.ly/3TP8Dh2
10% off code - GUNFLINT10
Brunt Work Gear: bit.ly/42tzvYL
10% off First Order over $60 - GUNFLINT10
Starbond CA Glue: bit.ly/2EjSRpC
15% off code - GUNFLINT15
Monport Lasers: bit.ly/49qlOfs
10% off code - GUNFLINT10
Rotoboss Rotary: bit.ly/3OQysdD
5% off with GUNFLINT
MagSwitch: bit.ly/3oxTVLj
10% off code - GUNFLINT10
My Basement Business: bit.ly/3OQJSht
15% off code - GUNFLINT15
Gunflint Designs is a participant in the Amazon Services LLC Associates Program.
Website: www.gunflintdesigns.com/proje...
Amazon Shop: www.amazon.com/shop/gunflintd...
Patreon: / gunflintdesigns
T-Shirts: www.amazon.com/dp/B07C3RJGHV
Instagram: / gunflintdesigns
Podcast: webuiltathing.libsyn.com/
Podcast Patreon: / webuiltathing - แนวปฏิบัติและการใช้ชีวิต
I love the walnut door! And I vote for a walnut top door! I love how form and function both rocked in this project!
Thank you very much!
Definitely make a top door!!!!!@@GunflintDesigns
That door turned out fantastic! With the magnetic shroud, it's gotta be darn near perfect when it comes to dust collection. Outstanding job! And +20points for the Karate Kid clip! Haha
There really isn't any dust that can escape the suction anymore!
Bottom door looks great!
I vote yes on a top door.
Thanks!
The shroud you put on at the end would be a game changer for all band saws.
Agreed! Link in the description ;)
Great work! I have a cousin to this saw made by Harbor Freight. It has a small shop vac port located where you installed the magnetic shroud. I like the looks of the new door A LOT more.
"Thin layer of dust" sounds like the cover band that plays in my shop.
This one had the same shop-vac hookup originally. I took it off and used a 4" hose bungeed to the saw in that location for years. This works much better!
This thing is amazing! I still think you should have painted it to match. ha ha. I was amazed at how well the dust collector was doing.
Brilliant work, Mark! 😊
Stay safe there with your family! 🖖😊
Thank you! Will do!
Looks awesome, Mark. Definitely give the top door the same treatment. And replace your Gunflint sticker with some CNC goodness while you’re at it.
I vote for walnut top too, and while you’re at it, how about a walnut stand for it to sit on. Get rid of all that blue, you’ll have the nicest bandsaw anyone has ever seen. You might even be able to move it to inside your house as a statement piece. 😂 looks amazing, great video.
I like where you're going with that! My dad used to have a kid's dirt bike sitting in the living room because it looked to him more like art than anything you could hang on the wall.
A top door is a definite now, especially when the bottom door looks so damn good 😊.
That sure seems to be the popular vote!
I think the inspiration you are providing is justification enough to continue with the walnut. Who says it’s unnesssry😳 What’s wrong with making an extremely useful machine beautiful as well. It’s a perfect blend of form and function. 😊
That door looks FANTASTIC and the magnetic shroud was definitely a good addition!
Thanks man!!
2:35 as far as the router goes, rather than pulling air from beneath with this type of bit, I tend to set up the fence a little bit back from the bit, but in the line of the chips, with dust collection hooked up to it. That way you get the safety of the correct size throat plate, and the dust collection sucks up most of it too.
Nice video Mark! That magnetically attached shroud is very cool! Dust collection is a big deal for your future health!
I build some custom parts for vehicles. I fill my scarf slots with epoxy but I add a filler. It maybe overkill but it's rock solid. "anything worth doing, is worth over doing".
That is always the right motto!
My dad use to say, "Don't do anything half-a**". Great work. Take care.@@GunflintDesigns
Love the look. Definitely make a top door to match!
Yes! Thank you!
Door looks great. My vote is for a top door to you went this far you might as well finish it off
Great video Mark! Top door for sure.
-WBAT Freeloader
Thanks! And at least you're honest!
Top door for sure
love my Oneida collector, too! Great mod and it looks great!!!
The bottom door on your saw looks absolutely amazing, but it would look a thousand times better with a matching top door. This video almost makes me want to do this to my Jet JBS-14 bandsaw, but I don't have hinges on the sides of the doors, just two screw on knobs, where you have only one on each door.
I am not sure I can think of a better use for unnecessary walnut.. perhaps that top door and the accent panels on the upright could do with some unnecessary walnut also? Nice work, Mark. Keep up the great videos.
It does seem like it could use some more doesn't it?
For the safety police around the 90 second mark - were it me, I know that it's an irrational fear, but I'd be really concerned about "my boys" getting caught in that spinning wheel. Great video! I don't have a bandsaw, but if I did, this would be a really tempting mod.
Sounds like you need to buy a bandsaw just so you can mod it!
Another note from the safety police: the "sketchy" cut on the table saw at @4:40 would have left me less queasy if you had hot glued or taped a block inside the piece that would help prevent the top from tipping down. But no blood or bruises, so good job holding it.
Love the door but man it sure would look nice painted to match the rest of the saw!
I agree!
I think you should slowly replace all the bandsaw parts with unnecessary Walnut! But yes, your time might be better spent on other projects. :D Awesome to see how well that new dust collection system is working, I need to do better about the collection on my stationary sanders.
I have an old craftsman belt/disk sander that will be the next on my list of messes to contain.
As always, a great video!!!
Glad you enjoyed it!
Mark, I heard about the door on the podcast and thought it was a clever idea you had, I can also see this catching on with other markers because of its functionality but it’s looks amazing you got to do the top and maybe a stand with storage for the accessories you use for the bandsaw with unnecessary walnut and maybe spray the other side as well to match the colour of the walnut, now I’m rambling on…..😂😂😂😂….great video
Haha, thank you! By the time I'm done with it there won't be anything metal left on it!
You should turn every panel into walnut.
ReMARKable!
Now you gotta do the top door.
Looks great! I probably would have just cut through the metal door myself... Haha! and maybe epoxied a border with some strong earth magnets to hold the dust sucker outer device to the metal door... but who knows? Maybe it would have taken just as long to fabricate and or make functional...and in the end... still won't look nearly as nice as yours!
I wanted to get into resawing and got an inexpensive Harbor Freight 14" bandsaw (used) only to see that it is FAR from capable for what I purchased it for... wanted to resaw 12" 2 x12s and the guide only allows a very minimal amount to go under it.... I wanted to experiment with welding (I don't have a welder either) 😅🤣😂 To extend the capability.... I'm trying to do cool stuff but on a budget... I, too, have a layer of dust all over the garage....😔
I like the idea of keeping the Large tube out of the way until needed. Excellent work!
Thanks Man! Sounds like you have lots of good ideas rattling around in your head.
Good video. I have a old Jet bandsaw and like yours. Does the single 4” port get rid of all the dust near the table and lower bearings? I noticed that you are still using the Jet cool blocks. I have upgraded to the Carter bearings for my saw and the tensioner. I think you find it a great improvement to your saw. Keep the video coming
Kevin Duxbury MA
That bandsaw doesn't look right now. You need to make new walnut upper door as well Mark.
I'm afraid you're right!
Please make a top door for the band saw
top door needed
I have the same bandsaw . Love the video I'm going to modify my door now lol. I am having a super hard time with blade drift. What kind of blades do you use and would you happen to have a video on tuning up the saw?
I'm not a bandsaw seyup expert, but I did make a few videos way back when I first got this saw... maybe they will be helpful?
th-cam.com/video/ociQmDu4g7E/w-d-xo.htmlsi=SMsMTC8FMFJExk00
th-cam.com/video/xu7D-h_QZhk/w-d-xo.htmlsi=CL4PaVF7asIwEmZX
look up alex snodgrass from carter bandsaws,, great videos on bandsaws
Absolutely make the top to match… then paint it
Thanks for listening to the podcast!
Just got a hole in the original bottom door and be done with it
The top door would definetly complete the look if you have the time and materials.
Definitely have the materials, probably the time too... but do I have the patience?
I think you need to unnecessarily make an unnecessary walnut upper door for the bandsaw as well!
Haha, well put!
‘Unnecessary walnut”. There is no such thing.