How to Fix A Broken Hydraulic Floor Jack That Won't Lift or is slow (Easy DIY - Bleed, refill etc.)
ฝัง
- เผยแพร่เมื่อ 9 ก.พ. 2025
- Quick how to fix a floor Jack That Won't Lift or that lifts very slowly. I'll do a follow up video on how to replace all seals for a full rebuild.
Help me fuel more content: www.buymeacoff...
![MUST HAVE TOOL! How To Fix or Rebuild a Floor Jack [BOTTLE JACK]](http://i.ytimg.com/vi/sk0FF6GFlqA/mqdefault.jpg)
![MUST HAVE TOOL! How To Fix or Rebuild a Floor Jack [BOTTLE JACK]](/img/tr.png)
Thanks Lech. Today I encountered my first floor jack failure and you showed all the steps to fix it clearly.
Nice. 👊
Thank you, Lech. Best thing about your video is that you, GOT TO THE POINT! No useless intro music or wasted words. Straight to the point. Good job. Thank you!
I try. My goal on all my videos. Thanks 🙏
Thx for the video. Will give this a try on my Pittsburgh jack.
Nice 👊
Did you fix it? I have a Pittsburgh jack too
No, the piston on the left side is broke. I ended up buying a Daytona 2 ton aluminum jack & it is smoother & easier to pump vs the Pittsburgh 2.5 ton aluminum. I hope I get more than 3 years from the Daytona jack vs the Pittsburgh 2.5 ton aluminum jack.
Just bought a Brand New Jack and was having trouble lifting. Did some research after watching your video on oils and added ATF lubricant I had laying around and it got the Job done now its working wonderfully 👍 👌
👍👊
Thanks. My 40 year old craftsman jack failed me this morning in the same way you demonstrate. I will try this technique to bleeding air from the system. I have no seal leaks, so I hope it is just a bit of air to purge.
Good luck 👊
Thank you! Going to go out and give it a try now.
👍
Thank you my guy very helpful and well explained 😊
I have a ProLift 2000kg from Australia, has the 3 adjusting screws, 2 on the left and one on the right. I Tried topping up the fluid still nothing, my manual says fill it till 12mm under the plug then just pump the handle while loose / valve released to remove any air, still would not lift under pressure only without pressure, so I took the first screw out it has a second adjusting screw below that so never touched it, took the second one out on the left side looking from the back, that screw only another cap to access the screw inside, so on the right side the single screw I removed it has a long stem to adjust the pressure, so I replaced it to where it was and kept doing it up bit by bit till the jack finally lifted under pressure. I wish they explained what each screw does but all it says don't adjust, they rather you send it off to make money off you, my jack only been used 5 times since new. Once I got it to lift under pressure I backed the screw out again, no more lift under pressure, so yeah Definitely the adjusting screw for pressure, so I did it up again till it lifted under pressure, just a bit at a time you don't want to go to crazy with the adjustment. God bless.
Thank for sharing. 👊
I think that first bolt, compression Piston, that you took out is welded in on mine
wow. i guess not meant to be touched. try the other i guess.
nice tutorial
👊
Very Good! Thank You!
👍
Thank you for your great video, hopefully I can fix mine I'll follow your tutorial.
Nice. Go for it
Ty for your knowledge
👍👊
I got a new one and it's not lifting after I added oil I'm assuming it has an oil leak...
Yeah. Might have a broken seal
That lifted so shite under the car at the end, i think u knew it & stopped 😂😂😂
Thanks!
👍👊
What oil did you put in there
Hydraulic jack oil
And here I thought this was at tutorial on how to spill oil all over your driveway.
😂
Wow! Amazing
👊👍
Oh that's funny mine's a Craftsman that's acting up like this too
top quality ;)