Excellent! I've been using the fg knot tying machine at home and it works very well but this knot will be employed now when I'm out fishing on my boat! Thanks for sharing!!!
I enjoyed your video but I will have to try this knot out before I judge. I night fish a lot and I think doing those quick over hand loops will be easier when it is dark and windy. 👍
Apa2 pun. Saya dah set calendar untuk tahun depan dah. Siap degan reminder sebulan awal. Pasti pi sana malam raya. Camping kat sana pun tak apa. 😂😂😂😂😂😂😂
Dude,… the FG is far superior…!!! If you can do a figure 8…. then you can tie an FG .. then finish it with a carrot knot …. Slicker than Buffalo snot …! 👍😎🤙
Little tip for anyone watching this.... Wrap the lines around a piece of dowel to fully tighten especially the braid. Youll not pull it up anywhere near as well with just just fingers. Is ok to make a video, but not to actually use. Try pulling braid tight enough to use, and it'll cut right into fingers, especially if you wrap braid around a finger to pull it tight
Once you get used to tying FG knots you can do it very quickly (as quickly as this). The finish is very similar, with numerous variations. The problem I see with this, as opposed to the FG is that the FG is successful because all of the twists have the ability to bite into the main line, creating the strength. Try tying an FG knot with too many turns (say 20) and the last twists will not bite in properly. This can lead to the final turns loosening, allowing the previous turns to also loosen. The same issue arises with this knot. I'd be interested to see some reports on longevity and failures under consistent load. For me, I'll stick with the FG...
i tie both fig tightens at the back then losens at the front of the knot while this one is opposite. so in terms of having final knot hold to be secured its not needed but just there
I had my 1st attempt fail. The mono leader pulled right out of the braid while casting a plastic frog. At 1st I though it broke my leader off because it wore from the knot clicking through my guides, but after I got my frog back I could see that the leader just pulled through the knot. 1st and only time in my life that that has happened with any braid to mono knot. It took me 30 casts with a crank bait to snag my frog. Incidentally, it was no less loud going through the guides than the uni-uni I normally use.
Very interesting, I do wonder how thoroughly it has been tested.. fg knot is tried and true and I don’t have any problem tying it but this is interesting 🤔
Great knot but won't cast through guides properly and is about 50%. And fg and allbright are 70% and the pr knot, which this is a poor man's version of is 100% knot. I doubt you are targeting large saltwater fish. Casting lures with braid joined to fluorocarbon leader
Hi, 1st of all tq for sharing I have tried this knot with my setup Daiwa Tatula 10-20lb , Steez , and my lure 20g , main line 30lb - leader 35lb. On 3rd cast, the lure flys on its own, the knot become loose and released. In my opinion, this knot maybe can be used for jigging. 50-50 for casting maybe light setup is suitable.
Don't overdo the loops. I personally think there were too many wraps in this demo. 12 to 15 is plenty and it allows you to snug down all the coils and properly tighten the knot all the way. If their are any loose coils it will eventually spread to all of them and allow the knot to fail.
This is half way towards a pr knot. Which is stronger than any knot. But with a bobbin you go 30 loops down, 60 loops back. 8 alternating 1/2 hitches, then finish with a risutto. That pr knot is 100 % knot. It takes longer to tie than an fg knot but its much stronger (100%)
PR needs to be wrapped tight just like the FG. Hence why we use a bobbin to wrap the trace while doing the PR and general PR should be long, atleast 30 wraps. The double Albright knot he's demonstrated is not just slack but also over exaggerated and too long.
Hello friend, truly congratulations, beautiful knot!🥰👏🏻👏🏻 Could you kindly tell me, for which PE diameters and techniques is it most suitable please? Could it be suitable for seabass and above? Thank you very much for the explanation. Best regards.
I can tie the FG fairly quick and I believe it’s smaller and it’s definitely strong I grouper fish with a gig never had it slip. I do tie mine at home. When I’m in the boat are wade fishing I tie the double unnie knot for speed it’s a little bigger but strong
This is my new favorite knot to use for braid to flouro leaders. I am not very quick at making it yet but getting better slowly. What is the name of this knot?
What is the reason for the half hitches in the middle ? Why not just do the last part of the knot and put like 8 or 10 wraps into that to lock it back into itself ? Or am I missing something ?
@@GeneFishingTV I just tried, once it settled seems pretty good. I'll give it a few tries when I go out tomorrow! Thanks! (BTW your milk cap knot helper is a great idea. I'm taking it one step further with polished oak! Making one for my fishing bud who comes home everytime with bloody knuckles.
CBX, you need to tie your half-knots the opposite direction you wrapped your line. If you wrapped your line over/under, your half knots need to tie under/over.
This knot is very good and strong while you use rather thick braid lines. But unfortunateky it is useless for thin braids used for ultralight like #0.3 - 0.4 PE and fluorcarbon line 0.18-0.22 mm. Such thin braids being damaged hard by this knot itself.
This is the knot I use for fishing 40 inch lake trout thru the ice. Strong knot!!
Investigator: So why did you do it!?
Me: he just kept twisting and twisting the damn braid. I couldn't take it anymore!
Literal LOL.
This knot is spectacular for tying 50lb braid to 100 lb fluorocarbon. Made my Tarpon rig so much better! Thanks!
Great to hear!😍
...been using the FG for a few years & become fairly good at it, but think I'll give this a try. Thanks.
Excellent! I've been using the fg knot tying machine at home and it works very well but this knot will be employed now when I'm out fishing on my boat! Thanks for sharing!!!
welcome buddy
First its looks like yucatan knot but in the end you improved it to fg knot, nice..thanks for the tutorial man 👍
thanks Muhamad
@@GeneFishingTV you are welcome 👍
Subok n subok Yan master.. tlgang wlang kawala....slmat s pag share NG tutorial m master...
salamat master
Mantap bang sambungan nya sangat simpel,jadi tambah pengetahuan lagi ni hee,trimakasih bang udah berbagi simpul cara sambung FE ke liderr👍🙏
makasih kawan 😊
Tying that knot is like waiting for an hour for a table to eat at McDonalds🤣
Comment of the year
I enjoyed your video but I will have to try this knot out before I judge. I night fish a lot and I think doing those quick over hand loops will be easier when it is dark and windy. 👍
Thanks brother God bless 😊🎣🌲
Aprendi a fazer esse nó assistindo seu vídeo, so faço ele nas minhas pescarias.Muito obrigado
Thanks a lot Julian
Just tried this SC Knot recently, easier to tie compare to FG Knot
nice to hear from you Jack thanks
Good tutorial and simple..thanks bro
Thanks bro
Just started using this leader knot it’s solid as can be
I thought I'd be smart and watch it at X2 speed, and it still took an hour. But,I do like the knot....so thankyou
it is easy and so strong. Thank you!
Thanks a lot buddy
Great FG knots
makasih kawan
Parabéns 👏👏👏. Um dos mais fácil de fazer. E dos melhores 👌
Best knot I've ever tried. Took me a few views to learn it lol
Thanks Jonathan
Best knot my frend... I like this 👍
Thanks a lot kawan😍😍
best my friend the string ties
Thanks a lot my friend
Easy and strong. Thanks
You're welcome!
This is the knot you'd use to tow a jeep out of mud
lolz 🙏😁
Thank you Sir for sharing, excellent video quality and superb demo. 10 out of 10. Learning from you master every time i watch your video.
Salamat master
If you think you're done wrapping the braid...you are knot! 😂
Lolz😃
Nice tutorial friend 👍👍
thanks my friend
My go to knot when jigging and fg for casting
surely strong and easy to tie. thanks buddy
Like all these videos. I know it's harder to see but show me these knots with 8-10lb braid to 6lb floro
Sure Chad thanks😊
Apa2 pun.
Saya dah set calendar untuk tahun depan dah. Siap degan reminder sebulan awal.
Pasti pi sana malam raya. Camping kat sana pun tak apa.
😂😂😂😂😂😂😂
Wow! Didn't even know this was possible. Will definitely try it out. Cannot do FG Knot b/c of difficulty and user error.
Please try and let me know if you did it 😊😊
Dude,… the FG is far superior…!!!
If you can do a figure 8…. then you can tie an FG .. then finish it with a carrot knot …. Slicker than Buffalo snot …!
👍😎🤙
Little tip for anyone watching this....
Wrap the lines around a piece of dowel to fully tighten especially the braid. Youll not pull it up anywhere near as well with just just fingers. Is ok to make a video, but not to actually use.
Try pulling braid tight enough to use, and it'll cut right into fingers, especially if you wrap braid around a finger to pull it tight
Mantap bossq,Newbies can follow this knot.good luck.godd job my friend
Thank you kawan 👍
Once you get used to tying FG knots you can do it very quickly (as quickly as this). The finish is very similar, with numerous variations. The problem I see with this, as opposed to the FG is that the FG is successful because all of the twists have the ability to bite into the main line, creating the strength. Try tying an FG knot with too many turns (say 20) and the last twists will not bite in properly. This can lead to the final turns loosening, allowing the previous turns to also loosen. The same issue arises with this knot. I'd be interested to see some reports on longevity and failures under consistent load.
For me, I'll stick with the FG...
i tie both fig tightens at the back then losens at the front of the knot while this one is opposite. so in terms of having final knot hold to be secured its not needed but just there
I had my 1st attempt fail. The mono leader pulled right out of the braid while casting a plastic frog. At 1st I though it broke my leader off because it wore from the knot clicking through my guides, but after I got my frog back I could see that the leader just pulled through the knot. 1st and only time in my life that that has happened with any braid to mono knot. It took me 30 casts with a crank bait to snag my frog. Incidentally, it was no less loud going through the guides than the uni-uni I normally use.
@@alienxyt as you already know the Uni knot works great. I been using it for over 35+ years. It's fast and easy to tie.
The principal is the same as an fg. Creating lots of surface area rather than a conventional knot which bites down tightly and cuts into itself.
Thank for sharing master
salamat maater
Very interesting, I do wonder how thoroughly it has been tested.. fg knot is tried and true and I don’t have any problem tying it but this is interesting 🤔
Make sure you Hawk tuah
Lol
Blood knot is still my go to knot
Great knot but won't cast through guides properly and is about 50%. And fg and allbright are 70% and the pr knot, which this is a poor man's version of is 100% knot. I doubt you are targeting large saltwater fish. Casting lures with braid joined to fluorocarbon leader
Thankyou for this video🙏
So nice of you bro thanks too.
Terima kasih info nya bro🤝💥🔥
Makasih bro 😍😊
Nice sharing master
thanks master
I'll be trying it out this weekend on some kingfish. Usually use the double uni but this one looks like it will cast through the eyes better. Thanks!
Thanks Cody
Exactly! That's why I'm here. 😅
Thank you for the good technique.+1❤
Thanks😊
Ikatan terbaik sahabat 🤙🎣
makasih kawan
Thank you for sharing ❤️❤️
Thanks for watching!
Awesome ❤
Thanks 🤗
Terima kasih tutornya, sangat bermanfaat
Makasih kawan ♥
Do you think you could finish with a rizuto instead and make it quicker and finer?
Yes I also use rizuto occasionally, its your own preference how you will lock the knot at the end buddy🙏😊
Sambungan yg sangat strong kawan
Makasih kawan 😍😍
Interesting. Is intricate but not difficult to tie.
try is my friend you will be surprised with the results
J'aime beaucoup bravo 👍👌😃💪🐟🎣
Thank you Alexandre
Yucatan knot is simple and effective.
That's perfect💯
Thanks kawan
Hi, 1st of all tq for sharing
I have tried this knot with my setup Daiwa Tatula 10-20lb , Steez , and my lure 20g , main line 30lb - leader 35lb. On 3rd cast, the lure flys on its own, the knot become loose and released. In my opinion, this knot maybe can be used for jigging. 50-50 for casting maybe light setup is suitable.
may I know what is your rod capacity buddy?
Don't overdo the loops. I personally think there were too many wraps in this demo. 12 to 15 is plenty and it allows you to snug down all the coils and properly tighten the knot all the way. If their are any loose coils it will eventually spread to all of them and allow the knot to fail.
Good knot..
thanks kawan 😍😍
This is half way towards a pr knot. Which is stronger than any knot. But with a bobbin you go 30 loops down, 60 loops back. 8 alternating 1/2 hitches, then finish with a risutto. That pr knot is 100 % knot. It takes longer to tie than an fg knot but its much stronger (100%)
Thanks Joe
PR needs to be wrapped tight just like the FG. Hence why we use a bobbin to wrap the trace while doing the PR and general PR should be long, atleast 30 wraps.
The double Albright knot he's demonstrated is not just slack but also over exaggerated and too long.
@@davidyang577 it is not a Double Albright, it's called an SC knot
Nice tutorial
Ahhh lepasni senang dah nak ikat ke pe 1 fg dkt pe bukan main susah nak ikat 🤣
Thank you
Thank you😊
mantap senior salam sehat dari kepulauan aru indonesia
Makasij kawan♥️
@@GeneFishingTV mantap kawan
SC-Knot❤
Hello friend, truly congratulations, beautiful knot!🥰👏🏻👏🏻
Could you kindly tell me, for which PE diameters and techniques is it most suitable please?
Could it be suitable for seabass and above?
Thank you very much for the explanation.
Best regards.
Yes this knot is for all types of fishing from light to heavy
Terimakasih ilmu x master..
Makasih kawan ♥
There is a little machine called Stonfo that does that job and it works excellent.
Thanks
I use this when slowpitching for tuna
Great knot is that the same as a SC knot or did i miss something.
I can tie the FG fairly quick and I believe it’s smaller and it’s definitely strong I grouper fish with a gig never had it slip. I do tie mine at home. When I’m in the boat are wade fishing I tie the double unnie knot for speed it’s a little bigger but strong
Yes buddy, I do the same but as a backup knot It is also good to try
Verry good
So the braid wraps around the mono and wraps around the mono and then the mono pulls right out from all those wraps.
I like that this knot has no tag end facing the rod tip, should make for a smooth cast...
Top demais amigo
FG knot secured with uni knot is way, wayyyy easier and strong enough 😅 My head hurt from looking at this 😆
you're either delusional or trolling. This method is much easier even though the process is identical. How is that pinky? 😂
@@jaimeruiz4313 I'm not delusional, I find the fg knot easier. Watch your mouth, mate.
yes its simpler but not stronger of course, and burning the leader means hits to the rings again. is it necessary?
burning the line is optional only. have you tried the knot?
Mantap bos. Salam dari
hengki chennel 47
makasih kawan
There are easier knots that hold just as well.
Yes I agree buds
@garycapley8686
Cukup sinpel dan mudah di pelajari
Makasih kawan ♥
Parabéns pelos vídeos.
Me ajudou bastante este nó 👏🏻👏🏻👏🏻👏🏻👊🏻👊🏻👊🏻👊🏻👊🏻
Thanks buddy
Je suis satisfait de le pouce
I counted like 32 wraps ! Then you would need another boat so you could tighten it up correctly! 2 boats would pull it together easily?
Музыка великолепная 🎶🎵🎤
What would be nice if you would do a break test when you tie all these knots after. More content and help your viewers.
I agree with that PI
In the amount of time it took to tie this knot I could have done 4. I'll stick with the FG
Tuyệt 6❤❤❤❤
Thank you :)
Чем больше накручу - тем больше наловлю...🤪
Пять минут вязать две лески между собой можно только когда рыба не клюет совсем
haha I agree it happens to sometimes, but I enjoyed fishing 😃🙏
Always alternate the half hich when finished.
This is my new favorite knot to use for braid to flouro leaders. I am not very quick at making it yet but getting better slowly. What is the name of this knot?
Its called SC knot Fernando 😊😊
What is the reason for the half hitches in the middle ?
Why not just do the last part of the knot and put like 8 or 10 wraps into that to lock it back into itself ?
Or am I missing something ?
The half hitches on the last part
ill stick to the double uni knot. way easier for me to tie.
J'aime beaucoup 😃😃😃🐟🐟🐟🎣🎣🎣🎣👌👌👌👌👍👍👍👍🦈🦈🦈💪💪💪
I'm waiting for wu tang to start rapping on that beat.
Is it any good with 10lb and below floro?
Never tried it yet, let me make a video out of it too.
@@GeneFishingTV I just tried, once it settled seems pretty good. I'll give it a few tries when I go out tomorrow! Thanks! (BTW your milk cap knot helper is a great idea. I'm taking it one step further with polished oak! Making one for my fishing bud who comes home everytime with bloody knuckles.
Honestly bro, if I break off and the fish are biting, do you really think I’ll be tying this knot lol, double uni all day bro, less than 15 seconds 💪
Looks very easy but carrot knot is faster;) unless your leader is not thinner than 0.18mm.
I’ve tried four times in my leader line slides right through the braid. What am I doing wrong?
try to wet the braid before tightening to prevent sliding
CBX, you need to tie your half-knots the opposite direction you wrapped your line. If you wrapped your line over/under, your half knots need to tie under/over.
I’ll suffer with my double uni 😂
Simple for micro braided line
It's starts like the albright... but ends other way... Começa igual o nó albright mas termina diferente.
Este eu pretendo praticar.
Sc knot brother
Good info
Glad it was helpful thanks a lot
This knot is very good and strong while you use rather thick braid lines. But unfortunateky it is useless for thin braids used for ultralight like #0.3 - 0.4 PE and fluorcarbon line 0.18-0.22 mm. Such thin braids being damaged hard by this knot itself.
Excelente, gratidão
Thank you Ricardo
What does FG mean?
fine grip
@@GeneFishingTV bullshit