Jolene is such a wonderful woman. She is a big help to you and always trying to learn something new. When a person isn't willing to learn something new they are as smart as they are ever going to be. I'm 72 and still learn all I can.
So true mate. I was talking to a guy at work yesterday....and between us we figured something out. I said to him “there ya go...we both learnt something today....it’s a good day” 👍
Great video. The trust and patience that Chad has with Jolene shows his true love for her. It brings joyful tears to one’s eyes to see their love and respect for each other. I am fortunate to have the same with my beautiful wife. Our wishes for the greatest success in your adventures.
Hi In order to get a long lasting quality result, you should have an epoxi primer on bare metal, I have seen great paintwork getting destroyed by blisters due to no primer under polyester sprayfiller. Body guy since 1981. Keep the good work going Take care From Sweden
The Directions for the product he is using clearly states "NOTE: All bare metal areas larger than one inch in diameter must be treated with a high quality self-etch or epoxy primer." That comes straight off of their web site.
Your shop is like my garage. If you had 20 more feet of bench space it would be covered with stuff and you still wouldn't have any room to set a gallon of primer.
I used to work for evercoat did bodywork paint we didn’t recommend laying down Feather fill Direct to metal the way is lay down epoxy primer and then lay down feather fill is Polyester Primer is Porous moisture be under your primer down the road you will have problems
Chad, I have much respect for you as a fabricator and a designer. I too build cars and have for 40 years. I know what it takes to achieve the end product that you create. I only have this last comment about the primer as a bit of information that you can take or toss it out as you see fit. I have spent the last 26 years as a manufactures rep for one of the largest automotive coatings companies in the world. I have a lot of experience behind what I am talking about. A large part of my job has been helping painters figure out what went wrong with their paint job. 99% of the time it has been because the painter did not follow the manufactures directions. The directions are for optimal results. The paint chemist that developed this product knows what it will and will not do. The manufacturer of the product has spent many hours testing with salt spray, adhesion and chip resistance. If it fails, they are usually held responsible. Unless it was not used correctly. The procedure that you use will work for a while. Long term, who knows because it was never intended to be used that way. The problems will come later after the hot sun and moisture attacks the finish. Yes 80 grit will provide adhesion. Epoxy is used for corrosion protection as well as adhesion. You cant get corrosion protection from sandpaper. The other potential problem is you over catalized the product. The fact that you had primer left over after using all 4 tubes of hardener tells this clearly. Over catalizing can result in a much slower cure time and can cause other potential long term problems. Please if you are going to teach, be responsible and teach it correctly. I’m sure Evercoat would prefer you teach your viewers the best way to use this primer. Not trying to bust your chops or come across as a know it all, but this is and has been my job for many years. I am a big fan and you have inspired me on my projects. Thank you!
I am curius. Some People talk about epoxi unerneath bodyfill. Whats your take on that?? How do I work with that for the best result?? Lets say i sanded and treated a heavy surface rust spot so the rust is gone but i want to fill it up to a nice finnish :)
@@kulan9379 Epoxy provides a layer of both adhesion and more importantly, corrosion protection. Many paint failures are not really paint related. I have seen multiple times when rust forms under the filler. It is caused by the peroxide in the hardener of the filler. I always epoxy before bodywork!
@@rexlindsey yes but how do i use it. Is it 36 grit the panel and then 1coat epoxy, lets say 1H before the epoxy is able to be coated with something else. Is it spray it on there wait 1H and then aplly Body fill it how is it done irl??
@@kulan9379 You can use 36, 40 or 80 grit then apply two coats of epoxy. You need enough film build or the epoxy will not work as it is intended. PPG epoxy will allow up to 7 days before sanding is required. You need to let the epoxy dry before applying body fill. Epoxy ‘s are slow to dry. I usually let it sit overnight before I put anything on top. I think my comments have been removed from his site. Hope this helps!
Great job guys !!! Just had my truck painted last year. Sure wish I had somebody take pride in there work like you do. I was so Disappointed. Sucks when you are super excited and then get taken by someone who just doesn’t take pride in there craft.
Jolene you did a great job girl don't even think you did anything wrong , but I will say as a painter it is hard to watch someone else paint .LOL I'm wanting put my hand through the phone .Lol and finish painting it myself lol.you do have a great teacher . Listen and learn and you'll be as good as he is very soon. peace out..
You talk with theory and practice at the same time. Life make you a teacher.Thanks a lot for your videos , really inspiring and cheerful.Say Hi to Joeline...GBY!
You promote confidence in yourself to someone… even with the gun comment.. doesnt matter the value of the item your using..its your skill that does the work.. great.
little tip for anyone, if yu wrap the airline around your wrist then over your shoulder it keeps it away from roof and hoods if you are a short arse like me :)
Hi Chad,. Did you drain the water from the compressor wipe down and clean metal with acetone spray a lite coat of etching primer on metal, and I hope the feather edge does not lift the old finish...happy sanding!!!!!!
You're so informative and thorough with everything you show on your page that not only do I think I can weld, I also think I can spray paint on a car now too! ❤
I am factory trained on this matter and painted thousands of high end cars. . If the car is properly prepared as in the case that Chad is doing it this will work perfectly. The instructions are for all bodymen from the do it yourself guy to the professional so laymen can have direction in case they don't know better. A professional knows by trial and error and by experience. It is funny that a person who isn't a professional can read something and give advise as if they know everything.
@@MarkJones-qn1eg I’m a factory trained painter also and every single manufacture of any and every automotive refinish product will tell you if you strip a car to bare metal it needs self etch or epoxy applied to it before primer. I would like to know what factory trained you and told you differently?
When you are teaching somebody to use the gun you should let them know that you pull the trigger partially and only the air comes out then you pull the trigger more and the paint comes out but when you pull the trigger a little bit you always have are coming out and then when you want the pain to come out you as you're rolling with your hand you pulled the trigger the rest of the way to lift the paint come out and at the end of each stroke you can let off the trigger a little bit to stop the paint flow when you need to
Chad and the beautiful Jolene, as people would call her, love your channel and the things that you do. I'm from Texas and a shed tree mechanic. keep up the great work. Love your projects and the way you help others. Keep up the great work.
great video.. when you started talking about trying not to spill primer it reminded me of doing that so much...when pouring primer like that and its full.. use some tape and go halfway around the upper part of your can and layer it.. then fold it a bit and run two more tape strips on the outter edges for support.. when you go to pour your primer it will act as one of those old timey oil spickets people used in those old oil cans.. when done and primer is done running back into the can just pull tape off.. just a trick I learned..
Chad your a very lucky man who has a wife that shares the same passion as you, cheers to both of you and more couples could should appreciate each other a bit more.
The Eastwood spec sheet says I can't use Featherfill directly onto bare metal. Do I first need to apply a self etching (or epoxy) primer on bare metal, then apply Featherfill on top of it?
G'DAY Chad & Jolene, great work with getting Primer laid down,the only prerequisite before spraying,that we have here in Queensland Australia is the checking and emptying of the water trap/ filter,as with our high humidity, moisture in air compressor and lines is a problem that must be addressed! To take up your challenge to call you out on a build or project,I've got one ,bring back your son Colten,to work to build your dream "CAFE RACER" style Kawasaki Z900 custom bike,to strip,restore and customise and have prepared and ready for paint,alongside the Bugatti,then have matching colour prized toys,as always Kindest Regards Dave McLaughlin Queensland Australia
Great job Jolene!! Like a pro. Always willing to learn. Can't wait to see the final results. Maybe Jolene gona be spraying the Bugatti. Your a quick study, I'm sure you can do it. Bad Chad is a great teacher..I look forward to watching you guys every day. Always interesting for sure.
Hi Chad and the beautiful Jolene, greetings from Ireland, absolutely Love your Channel and all your hard work and design skills, about that troublesome earth clamp on the mig welder have you ever considered adding a magnet instead of that crocodile clamp
Jolene you’re a beautiful human being Chad you’re a legend!!! Jolene doesn’t mind getting her hands and clothes dirty and learning the trade!! Chad loves to hand that incredible knowledge on!!! Great couple!!
I believe you are correct. She is a natural. All she needs now is to know what she’s looking at as she does it. With practice I think she could lay down a perfect coat of paint
I am excited for more of this education. Chad you are an excellent teacher. Jolene you are an excellent camerawoman. Thank you both for sharing these videos with us. They are all educational and entertaining. I hope you will continue to post here on TH-cam. Everyone be sure to Like, Subscribe, and Share Bad Chad. Click the notification bell so you don't miss any premiers where you can chat with all of us and sometimes even Bad Chad and Jolene. #DRIVABLEARTWORK
Chad, strange choice, especially when Evercoat's own TDS says not to use this over bare metal surfaces of more than 1 square inch. They say to use this product over epoxy primer on bare metals. I can only think the longevity of the paint will be affected, this being a high solids, sandable primer.
Chad I love the way u got Jolene to prime and mask. Jolene gun more straight down over surface and a little slower and 50% overlap. But u did good girl. Love your videos u 2.
i use tuff coat for a primer works good and bonds better first i use an etching primer for rust or metal surfaces for industrial paint jobs it is really strong hard to scrap with a knife then the tuff coat is a strong thick primer sandable for industrial paint jobs then seal and paint i get this stuff cheap real cheap but it normally cost twice as much if not a lot more i get dupont paint products 10% above the cost to make it from the owner of dupont but only for my projects only . a gal. sentary 5000 black with a gal of tuff with reducer for both for 50 bucks 1 stage paint 2 stage add 30 bucks
Youll find the best usually don't follow instructions, i learned from someone else so far no problems dtm with g2--- also remember these are usually garaged or show queens they'll never see the conditions of an everyday driver
The more you paint Jolene the better you get at it keep up the great work. We need more women auto painter's there's not that many of them. In the automotive industry that is.
The Featherfill G2 Tech sheet says not recommended to spray over bare metal. You should always use an epoxy or etch primer on bare metal DTM works as well. Nothing that Im an expert, I just read directions from time to time lol
Those harbor freight guns that are like $15 with a coupon do a decent job with primer. Cheap enough you could throw it away rather than waste your time cleaning it.
Chad, does paint now adhere better at masking lines than it used to? When I was a kid, we always pulled the windows and all of the trim. How long do you expect this paint job to last before it starts peeling away at the mask lines? Is the paint water-based? BTW, I like your TV Show but I really like your TH-cam. Are you doing another season on TV as well?
Hi Chad & Jolene, great videos. Your shop is more like the typical working man's garage than anything I've seen on UTUBE. Very educational. Will you give us some pointers on prepping the mid 80's typical deep surface rust bodys with equipment like yours. You prefer acid, sanding, blasting, or other to deal with deep rust pits. HELP ME. Thanks Billy J.
We noticed in a recent video you were using an electric da sander. My husband is disabled in a wheel chair and he thought that would be better than an air one. WE live outside of moncton and have been trying to find one. Where did you get yours? We watch every video, it is amasing what you do.
Gosh man I've painted many many cars from model A to Ts from Ferraris to Lamborghini even a few Germans Japanese and American cars too mind you....all in my brain that is😂😂😂😂😂
Jolene is such a wonderful woman. She is a big help to you and always trying to learn something new. When a person isn't willing to learn something new they are as smart as they are ever going to be. I'm 72 and still learn all I can.
So true mate. I was talking to a guy at work yesterday....and between us we figured something out. I said to him “there ya go...we both learnt something today....it’s a good day” 👍
Very fun to watch you both work together. Jolene is a real natural. Great videos!
This is the best channel to learn how to do body work excellent job both of you guys
Great video. The trust and patience that Chad has with Jolene shows his true love for her. It brings joyful tears to one’s eyes to see their love and respect for each other. I am fortunate to have the same with my beautiful wife. Our wishes for the greatest success in your adventures.
I always soak the floor down the moisture helps clear the air.
Never seen anyone wet down the floor for primer
@@Dennis-eh2vx it helps to remove the dust from the air I should know I do it all the time .try it and wait 5 minutes you'll see.
Hi
In order to get a long lasting quality result, you should have an epoxi primer on bare metal, I have seen great paintwork getting destroyed by blisters due to no primer under polyester sprayfiller. Body guy since 1981.
Keep the good work going
Take care
From Sweden
That’s what I’m understanding , but would you be able to paint right over this polyester primer ?
@@Obs.societynot without sanding it first, no.
Yes, I think a coat of epoxy primer before the Evercoat would have been advisable.
The Directions for the product he is using clearly states "NOTE: All bare metal areas larger than one inch in diameter must be
treated with a high quality self-etch or epoxy primer." That comes straight off of their web site.
It say apply to epoxy primer. Will not stick to bare metal.
Your shop is like my garage. If you had 20 more feet of bench space it would be covered with stuff and you still wouldn't have any room to set a gallon of primer.
That's how my house is 🤣🤣🤣 i have to many hobbies ..my living room. Turned in to a studio ....my table computer desk you name it,it's covered man 😅😂🤟
I used to work for evercoat did bodywork paint we didn’t recommend laying down Feather fill Direct to metal the way is lay down epoxy primer and then lay down feather fill is Polyester Primer is Porous moisture be under your primer down the road you will have problems
Chad, I have much respect for you as a fabricator and a designer. I too build cars and have for 40 years. I know what it takes to achieve the end product that you create. I only have this last comment about the primer as a bit of information that you can take or toss it out as you see fit. I have spent the last 26 years as a manufactures rep for one of the largest automotive coatings companies in the world. I have a lot of experience behind what I am talking about. A large part of my job has been helping painters figure out what went wrong with their paint job. 99% of the time it has been because the painter did not follow the manufactures directions. The directions are for optimal results. The paint chemist that developed this product knows what it will and will not do. The manufacturer of the product has spent many hours testing with salt spray, adhesion and chip resistance. If it fails, they are usually held responsible. Unless it was not used correctly. The procedure that you use will work for a while. Long term, who knows because it was never intended to be used that way. The problems will come later after the hot sun and moisture attacks the finish. Yes 80 grit will provide adhesion. Epoxy is used for corrosion protection as well as adhesion. You cant get corrosion protection from sandpaper. The other potential problem is you over catalized the product. The fact that you had primer left over after using all 4 tubes of hardener tells this clearly. Over catalizing can result in a much slower cure time and can cause other potential long term problems. Please if you are going to teach, be responsible and teach it correctly. I’m sure Evercoat would prefer you teach your viewers the best way to use this primer. Not trying to bust your chops or come across as a know it all, but this is and has been my job for many years. I am a big fan and you have inspired me on my projects.
Thank you!
I am curius. Some People talk about epoxi unerneath bodyfill. Whats your take on that?? How do I work with that for the best result?? Lets say i sanded and treated a heavy surface rust spot so the rust is gone but i want to fill it up to a nice finnish :)
@@kulan9379 Epoxy provides a layer of both adhesion and more importantly, corrosion protection. Many paint failures are not really paint related. I have seen multiple times when rust forms under the filler. It is caused by the peroxide in the hardener of the filler. I always epoxy before bodywork!
@@rexlindsey yes but how do i use it. Is it 36 grit the panel and then 1coat epoxy, lets say 1H before the epoxy is able to be coated with something else. Is it spray it on there wait 1H and then aplly Body fill it how is it done irl??
@@kulan9379 You can use 36, 40 or 80 grit then apply two coats of epoxy. You need enough film build or the epoxy will not work as it is intended. PPG epoxy will allow up to 7 days before sanding is required. You need to let the epoxy dry before applying body fill. Epoxy ‘s are slow to dry. I usually let it sit overnight before I put anything on top.
I think my comments have been removed from his site. Hope this helps!
@@rexlindsey ok thx mate for the lesson helps alot :)
Practice makes perfect, great job Chad and Jolene.👍
Spraying is SUCH a great reward for a good prep job ! Pretty too!
Nice teamwork! Chad is a great instructor. Always a pleasure to watch you two.
You and your cheap paint guns! I Love it.. goes to show it's not about the tool it's about who is using it.
Awesome! Great job, Jolene! Chad, you're an excellent teacher 😊
Good job Chad, very informative. Nice to see Jolene in there lending a hand doing the priming.
Great job guys !!!
Just had my truck painted last year. Sure wish I had somebody take pride in there work like you do. I was so
Disappointed. Sucks when you are super excited and then get taken by someone who just doesn’t take pride in there craft.
Jolene you did a great job girl don't even think you did anything wrong , but I will say as a painter it is hard to watch someone else paint .LOL I'm wanting put my hand through the phone .Lol and finish painting it myself lol.you do have a great teacher . Listen and learn and you'll be as good as he is very soon. peace out..
You talk with theory and practice at the same time. Life make you a teacher.Thanks a lot for your videos , really inspiring and cheerful.Say Hi to Joeline...GBY!
You promote confidence in yourself to someone… even with the gun comment.. doesnt matter the value of the item your using..its your skill that does the work.. great.
The buzz of the paint sets in during the second coat as chad goes into a zen quiet mode and enjoys the buzz.
little tip for anyone, if yu wrap the airline around your wrist then over your shoulder it keeps it away from roof and hoods if you are a short arse like me :)
Hi Chad,. Did you drain the water from the compressor wipe down and clean metal with acetone spray a lite coat of etching primer on metal, and I hope the feather edge does not lift the old finish...happy sanding!!!!!!
It’s FRIDAY! Looking good all primed up...
You're so informative and thorough with everything you show on your page that not only do I think I can weld, I also think I can spray paint on a car now too! ❤
The data sheet for Evercoat Feather fill G2 states it needs to be applied over epoxy primer, not on bare metal.
still, better than the engine work being bartered for ?
Nasty
I am factory trained on this matter and painted thousands of high end cars. . If the car is properly prepared as in the case that Chad is doing it this will work perfectly. The instructions are for all bodymen from the do it yourself guy to the professional so laymen can have direction in case they don't know better. A professional knows by trial and error and by experience. It is funny that a person who isn't a professional can read something and give advise as if they know everything.
@@MarkJones-qn1eg I’m a factory trained painter also and every single manufacture of any and every automotive refinish product will tell you if you strip a car to bare metal it needs self etch or epoxy applied to it before primer. I would like to know what factory trained you and told you differently?
Will see who is correct when he's done. I know who I am betting on. Not his first rodeo.
Love your videos and lessons,Joleen is terrific what a lucky guy you are Chad !
Thats GREAT , you brought back IT's FRIDAAAAYY !!!
I would recommend some kind of wash primer on the metal
When you are teaching somebody to use the gun you should let them know that you pull the trigger partially and only the air comes out then you pull the trigger more and the paint comes out but when you pull the trigger a little bit you always have are coming out and then when you want the pain to come out you as you're rolling with your hand you pulled the trigger the rest of the way to lift the paint come out and at the end of each stroke you can let off the trigger a little bit to stop the paint flow when you need to
she's a natural and it was great to see you give some coaching tips to teach a novice painter and film. Good switch up. Love the content.
Excellent videos,glad I took the time to watch.a good refresher education to help me with my projects. Good job the both of you😁👍
Chad and the beautiful Jolene, as people would call her, love your channel and the things that you do. I'm from Texas and a shed tree mechanic. keep up the great work. Love your projects and the way you help others. Keep up the great work.
great video.. when you started talking about trying not to spill primer it reminded me of doing that so much...when pouring primer like that and its full.. use some tape and go halfway around the upper part of your can and layer it.. then fold it a bit and run two more tape strips on the outter edges for support.. when you go to pour your primer it will act as one of those old timey oil spickets people used in those old oil cans.. when done and primer is done running back into the can just pull tape off.. just a trick I learned..
You guys are doing something great, educational and fun.
A couple that plays together stays together.....another informative video.....well done guys.
Jolene you did a great job with the gun another great video.
You and your wife are awsome thanks for teaching us, legends.
Chad your a very lucky man who has a wife that shares the same passion as you, cheers to both of you and more couples could should appreciate each other a bit more.
yup' it takes a lot of skill to do it all in one take and keep the audiance engaged well done
I like Chad I like him I THINK HE IS VERY SMART,
The Eastwood spec sheet says I can't use Featherfill directly onto bare metal. Do I first need to apply a self etching (or epoxy) primer on bare metal, then apply Featherfill on top of it?
Yes. As stated on the TDS
Technical data sheet.
He’s one of the most random thinking people I know but it’s all about the same thing if ya know what I’m saying :) awesome videos and good camera work
These videos are awesome! Really pumping me up to get crackin on the bagged '52 Chevy I'm building over on my channel! Can't wait to get to body work!
G'DAY Chad & Jolene, great work with getting Primer laid down,the only prerequisite before spraying,that we have here in Queensland Australia is the checking and emptying of the water trap/ filter,as with our high humidity, moisture in air compressor and lines is a problem that must be addressed! To take up your challenge to call you out on a build or project,I've got one ,bring back your son Colten,to work to build your dream "CAFE RACER" style Kawasaki Z900 custom bike,to strip,restore and customise and have prepared and ready for paint,alongside the Bugatti,then have matching colour prized toys,as always Kindest Regards Dave McLaughlin Queensland Australia
Hello I was told the evercoat g2 primer wasn’t a direct to metal primer the super build 4 to 1 was
Just like laying shingles painting is just like laying shingles on a roof or a house overlap 👍
Great job Jolene!! Like a pro. Always willing to learn. Can't wait to see the final results. Maybe Jolene gona be spraying the Bugatti. Your a quick study, I'm sure you can do it. Bad Chad is a great teacher..I look forward to watching you guys every day. Always interesting for sure.
Great Stuff Chad & Jolene !!! Thank You Both !
Hi Chad and the beautiful Jolene, greetings from Ireland, absolutely Love your Channel and all your hard work and design skills, about that troublesome earth clamp on the mig welder have you ever considered adding a magnet instead of that crocodile clamp
Chad. I would have put etch primer first. I sprayed lots of that primer.
It tells you on the can not to spray on bare metal lol
Learned a lot Thanks Chad and Jolene fine details are everything
You go ... laying it out heavy. Bare metal is something that absorbes moisture on a nother level . Is that etching prime with acid .
Awesome video as usual....I can watch...and watch...and a new build...hot damn!!!
Thankyou for these videos Chad I'm going to give the windex a try next time I'm topcoating something.
what an amazing woman you have their Chad ...you are one lucky man
Jolene you’re a beautiful human being Chad you’re a legend!!!
Jolene doesn’t mind getting her hands and clothes dirty and learning the trade!!
Chad loves to hand that incredible knowledge on!!!
Great couple!!
Jolene is going to make a great painter. I mean it! She has a great form for a beginner and I believe will be a easy student.
I believe you are correct. She is a natural. All she needs now is to know what she’s looking at as she does it. With practice I think she could lay down a perfect coat of paint
Excellent job Jolene
I am excited for more of this education. Chad you are an excellent teacher. Jolene you are an excellent camerawoman. Thank you both for sharing these videos with us. They are all educational and entertaining. I hope you will continue to post here on TH-cam. Everyone be sure to Like, Subscribe, and Share Bad Chad. Click the notification bell so you don't miss any premiers where you can chat with all of us and sometimes even Bad Chad and Jolene. #DRIVABLEARTWORK
Chad, strange choice, especially when Evercoat's own TDS says not to use this over bare metal surfaces of more than 1 square inch. They say to use this product over epoxy primer on bare metals. I can only think the longevity of the paint will be affected, this being a high solids, sandable primer.
I am starting to get your perspective on polyester primers. If you really wait a long time (2-3 weeks) without heat, no cracking is to be expected.
GREAD JOB CHAD; YOU DO GREAT WORK IT IS A PLEASER WATCHING YOU,
Chad I love the way u got Jolene to prime and mask. Jolene gun more straight down over surface and a little slower and 50% overlap. But u did good girl. Love your videos u 2.
This car looks phenomenal Chad! Nice to see Jolene in the video as well. 😀
Nice job jolene did great on the gun one step closer
Jolene looks good everyday
i use tuff coat for a primer works good and bonds better first i use an etching primer for rust or metal surfaces for industrial paint jobs it is really strong hard to scrap with a knife then the tuff coat is a strong thick primer sandable for industrial paint jobs then seal and paint i get this stuff cheap real cheap but it normally cost twice as much if not a lot more i get dupont paint products 10% above the cost to make it from the owner of dupont but only for my projects only . a gal. sentary 5000 black with a gal of tuff with reducer for both for 50 bucks 1 stage paint 2 stage add 30 bucks
I always try to follow all your videos, your work is great.
Thanks you two! Cheers 🍻
I love how slow and smooth jolene’s filming is
I started putting head lamps on my cups for extra lighting
Great prime application by both. 😎👍🇨🇦
Youll find the best usually don't follow instructions, i learned from someone else so far no problems dtm with g2--- also remember these are usually garaged or show queens they'll never see the conditions of an everyday driver
I was getting very nervous watching her but it’s only primer and she’s gorgeous
Love the way you work together with your woman
The more you paint Jolene the better you get at it keep up the great work. We need more women auto painter's there's not that many of them. In the automotive industry that is.
The Featherfill G2 Tech sheet says not recommended to spray over bare metal. You should always use an epoxy or etch primer on bare metal DTM works as well. Nothing that Im an expert, I just read directions from time to time lol
I´m learning watching your grate videos. Friday-cheers from Sweden. SKÅL
Use 3 m disposable cups built in filters and you could put a cap to save most products
Would love to see you build a tail dragger
It’s Friday.....great primer job guys.
what a nice job you guys are doing...its going to be great.
Great video. How do you clean your air? Do you have a dryer on your compressor? Thanks for making real life videos.
great video you make it look so easy, can i ask what spray tip is being used on your primer gun? thanks
Those harbor freight guns that are like $15 with a coupon do a decent job with primer. Cheap enough you could throw it away rather than waste your time cleaning it.
I think it would be nice to see how you would build boat tail speedster. I think those cars are 🔥.
That exhaust fan must be some kind of color art.
Chad, does paint now adhere better at masking lines than it used to? When I was a kid, we always pulled the windows and all of the trim. How long do you expect this paint job to last before it starts peeling away at the mask lines? Is the paint water-based? BTW, I like your TV Show but I really like your TH-cam. Are you doing another season on TV as well?
Hi Chad & Jolene, great videos. Your shop is more like the typical working man's garage than anything I've seen on UTUBE. Very educational. Will you give us some pointers on prepping the mid 80's typical deep surface rust bodys with equipment like yours. You prefer acid, sanding, blasting, or other to deal with deep rust pits. HELP ME. Thanks Billy J.
You both did a great job. Looks great 👍
The width of your pattern and distance from your work is the Span Of The Hand. With a Candy paint your overlap is minimum 75%
Using Windex just like Fitzee. Great minds think alike.
Awesome Jolene..love the way Chad respects you. Great motivated teacher.
Where is the etch primer for bare metal or is that a epoxy primer?
Lookin Good. Good job Jolene.
We noticed in a recent video you were using an electric da sander. My husband is disabled in a wheel chair and he thought that would be better than an air one. WE live outside of moncton and have been trying to find one. Where did you get yours? We watch every video, it is amasing what you do.
Quite the thing to be able to say "The first car I painted was a jaguar! "
Gosh man I've painted many many cars from model A to Ts from Ferraris to Lamborghini even a few Germans Japanese and American cars too mind you....all in my brain that is😂😂😂😂😂
You should try a H.V.L.P gun .. you'll be surprised how good a finish you can get 🤘🤘
Foolish question but longer strokes or shorter strokes when painting primer or paint which is better 😁😁😁
Always use the g2, great product